FCC ID MSQBE211NG

SAR testing was performed to demonstrate portable RF compliance for the PIFA antenna for each distance/SKU. This module is approved in portable configurations with PIFA reference antenna (2.95 dBi). For 40mm SKU: The highest reported Body and Simultaneous SAR values are 0.07 W/kg and 1.55 W/kg respectively. This filing meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference antenna(s): PIFA reference antenna (2.95 dBi), Dipole reference antenna (2.95 dBi) and Monopole reference antenna (2.83 dBi).

This C2PC filing establishes portable category for ASUS platform with models: B5406FMA and B5456FMA, with permanently adjusting the power through BIOS that cannot be changeable by the end-users. SAR measurement was performed to demonstrate RF Exposure compliance. The highest reported Body and Simultaneous SAR values are 0.39 W/kg and 1.59 W/kg, respectively. Antennas used - PIFA with Part numbers: RAN01RY7200001 (main and aux) manufactured by Luxshare; and RAN01RY7200002 (main and aux) manufactured by AWAN. This device contains 2.4GHz BLE/WLAN and 5GHz/6GHz WLAN transmitters.

Modular Approval filing. This grant covers BT-HADM mode of operation. The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. Grantee must provide installation and operating instructions for complying with FCC multi-transmitter product procedures. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter. End-users and installers must be provided with transmitter operating conditions for satisfying RF exposure compliance.

SAR testing was performed to demonstrate portable RF compliance for the PIFA antenna for each distance/SKU. This module is approved in portable configurations with PIFA reference antenna (2.95 dBi).

For 40mm SKU: The highest reported Body and Simultaneous SAR values are 0.07 W/kg and 1.55 W/kg respectively.

The additional SKU/power profiles determine conditions based on modular stand-alone SAR evaluation to establish the minimum antenna to user separation distances (5mm, 8mm and 11mm) at a maximum SAR value less than 0.8W/kg(1g) for mixed mobile/portable conditions according to KDB 447498 D01 General RF Exposure Guidance v06 and KDB 616217 D04 for Laptop and Tablets v01.

SKU 5 mm: The highest reported Body and Simultaneous SAR values are: 0.75 W/kg and 1.44 W/kg respectively.

SKU 8 mm: The highest reported Body and Simultaneous SAR values are: 0.71 W/kg and 1.57 W/kg respectively.

SKU 11mm: The highest reported Body and Simultaneous SAR values are: 0.43 W/kg and 1.59 W/kg respectively.

This filing meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference antenna(s): PIFA reference antenna (2.95 dBi).

Power Output listed is EIRP. The first five rows above are for LPI mode and the remaining rows are for Standard mode. Modular Approval filing. Device is a 2 x 2 MIMO configuration, enabled for 6 GHz operations as described in this filing. The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. Grantee must provide installation and operating instructions for complying with FCC multi-transmitter product procedures. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter. End-users and installers must be provided with transmitter operating conditions for satisfying RF exposure compliance. This device supports 20, 40, 80,160, and 320 MHz BW modes.

Power Density and SAR testing was performed to demonstrate portable RF compliance for the PIFA antenna for each distance/SKU. This module is approved in portable configurations with PIFA reference antenna (4.88 to 5.02 dBi).

For 40mm SKU: The highest reported Body and Simultaneous SAR values are 0.68 W/kg and 1.55 W/kg respectively.

The additional SKU/power profiles determine conditions based on modular stand-alone SAR evaluation to establish the minimum antenna to user separation distances (5mm, 8mm and 11mm) at a maximum SAR value less than 0.8W/kg(1g) for mixed mobile/portable conditions according to KDB 447498 D01 General RF Exposure Guidance v06 and KDB 616217 D04 for Laptop and Tablets v01.

SKU 5 mm: The highest reported Body and Simultaneous SAR values are: 0.80 W/kg and 1.44 W/kg respectively.

SKU 8 mm: The highest reported Body and Simultaneous SAR values are: 0.80 W/kg and 1.57 W/kg respectively.

SKU 11mm: The highest reported Body and Simultaneous SAR values are: 0.80 W/kg and 1.59 W/kg respectively.

This filing meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference This filing meets MPE requirements of KDB 447498 an antenna(s): PIFA reference antenna (4.88 to 5.02 dBi), Dipole reference antenna (4.49 to 5.02 dBi) and Monopole reference antenna (4.79 to 4.91 dBi). The minimum gain approved with the UNII-5 to UNII-8 bands is -2.0 dBi.

SAR testing was performed to demonstrate portable RF compliance for the PIFA antenna for each distance/SKU. This module is approved in portable configurations with PIFA reference antenna (2.95 dBi). For 40mm SKU: The highest reported Body and Simultaneous SAR values are 0.07 W/kg and 1.55 W/kg respectively. This filing meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference antenna(s): PIFA reference antenna (2.95 dBi).

This C2PC filing establishes portable category for ASUS platform with models: B5406FMA and B5456FMA, with permanently adjusting the power through BIOS that cannot be changeable by the end-users. SAR measurement was performed to demonstrate RF Exposure compliance. The highest reported Body and Simultaneous SAR values are 0.39 W/kg and 1.59 W/kg, respectively. Antennas used - PIFA with Part numbers: RAN01RY7200001 (main and aux) manufactured by Luxshare; and RAN01RY7200002 (main and aux) manufactured by AWAN. This device contains 2.4GHz BT/BLE/WLAN and 5GHz/6GHz WLAN transmitters.

Modular Approval. Power Output listed is conducted for UNII-1 to UNII-3 and EIRP for UNII-4 bands. UNII-4 band is for indoor operation only. The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. Grantee must provide installation and operating instructions for complying with FCC multi-transmitter product procedures. This module is approved in mobile/portable configurations. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter. Grantee must coordinate with OEM integrator to determine applicable host configurations to ensure RF exposure compliance, including simultaneous transmission SAR requirements according to published KDB 616217 supplement documentation. When all conditions of this filing cannot be met installation of this device into specific final products may require the submission of a permissive change application, containing appropriate data demonstrating compliance, or a new application. This transmitter has 20MHz, 40MHz, 80MHz, 160 MHz bandwidth modes as described in this filing. Device is a client only device containing a 2 x 2 MIMO configuration, enabled for either 2.4 or 5 GHz band operations as described in this filing. OEM/Host integrator must be provided with antenna installation instructions and transmitter operating conditions to satisfy RF exposure compliance. OEM/Host integrator is responsible for complying with the instructions and requirements for each transmitter they choose to integrate into a host product.

SAR testing was performed to demonstrate portable RF compliance for the PIFA antenna for each distance/SKU. This module is approved in portable configurations with PIFA reference antenna (5.11 to 5.15 dBi).

For 40mm SKU: The highest reported Body and Simultaneous SAR values are 0.79 W/kg and 1.55 W/kg respectively.

The additional SKU/power profiles determine conditions based on modular stand-alone SAR evaluation to establish the minimum antenna to user separation distances (5mm, 8mm and 11mm) at a maximum SAR value less than 0.8W/kg(1g) for mixed mobile/portable conditions according to KDB 447498 D01 General RF Exposure Guidance v06 and KDB 616217 D04 for Laptop and Tablets v01.

SKU 5 mm: The highest reported Body and Simultaneous SAR values are: 0.77 W/kg and 1.44 W/kg respectively.

SKU 8 mm: The highest reported Body and Simultaneous SAR values are: 0.80 W/kg and 1.57 W/kg respectively.

SKU 11mm: The highest reported Body and Simultaneous SAR values are: 0.79 W/kg and 1.59 W/kg respectively.

This filing meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference antenna(s): PIFA reference antenna (5.11 to 5.15 dBi), Dipole reference antenna (4.03 to 5.15 dBi) and Monopole reference antenna (4.43 to 4.95 dBi).

The host-product antenna must be permanently installed and not replaceable by the end user. Any attempt to replace or modify the antenna by the end user is strictly prohibited and will void the FCC certification.

This device supports 20, 40, 80,160, and 320 MHz BW modes.

Power Density and SAR testing was performed to demonstrate portable RF compliance for the PIFA antenna for each distance/SKU. This module is approved in portable configurations with PIFA reference antenna (4.88 to 5.02 dBi).

For 40mm SKU: The highest reported Body and Simultaneous SAR values are 0.68 W/kg and 1.55 W/kg respectively.

The additional SKU/power profiles determine conditions based on modular stand-alone SAR evaluation to establish the minimum antenna to user separation distances (5mm, 8mm and 11mm) at a maximum SAR value less than 0.8W/kg(1g) for mixed mobile/portable conditions according to KDB 447498 D01 General RF Exposure Guidance v06 and KDB 616217 D04 for Laptop and Tablets v01.

SKU 5 mm: The highest reported Body and Simultaneous SAR values are: 0.80 W/kg and 1.44 W/kg respectively.

SKU 8 mm: The highest reported Body and Simultaneous SAR values are: 0.80 W/kg and 1.57 W/kg respectively.

SKU 11mm: The highest reported Body and Simultaneous SAR values are: 0.80 W/kg and 1.59 W/kg respectively.

This filing meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference antennas: PIFA reference antenna (4.88 to 5.02 dBi), Dipole reference antenna (4.49 to 5.02 dBi) and Monopole reference antenna (4.79 to 4.91 dBi). The minimum gain approved with the UNII-5 to UNII-8 bands is -2.0 dBi.

Power Output listed is conducted. Modular Approval. Power output has been reduced at the upper bandedge channels as shown in filings under this FCC ID. The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. Grantee must provide installation and operating instructions for complying with FCC multi-transmitter product procedures. This module is approved in mobile/portable configurations. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter. Grantee must coordinate with OEM integrator to determine applicable host configurations to ensure RF exposure compliance, including simultaneous transmission SAR requirements according to published KDB 616217 Supplement documentation. When all conditions of this filing cannot be met installation of this device into specific final products may require the submission of a permissive change application, containing appropriate data demonstrating compliance, or a new application. OEM/Host integrator must be provided with antenna installation instructions and transmitter operating conditions to satisfy RF exposure compliance. Device is a client only device containing a 2 x 2 MIMO configuration, enabled for either 2.4 or 5 GHz band operations as described in this filing. OEM/Host integrator is responsible for complying with the instructions and requirements for each transmitter they choose to integrate into a host product.

SAR testing was performed to demonstrate portable RF compliance for the PIFA antenna for each distance/SKU. This module is approved in portable configurations with PIFA reference antenna (2.95 dBi).

For 40mm SKU: The highest reported Body and Simultaneous SAR values are 0.31 W/kg and 1.55 W/kg respectively.

The additional SKU/power profiles determine conditions based on modular stand-alone SAR evaluation to establish the minimum antenna to user separation distances (5mm, 8mm and 11mm) at a maximum SAR value less than 0.8W/kg(1g) for mixed mobile/portable conditions according to KDB 447498 D01 General RF Exposure Guidance v06 and KDB 616217 D04 for Laptop and Tablets v01.

SKU 5 mm: The highest reported Body and Simultaneous SAR values are: 0.75 W/kg and 1.44 W/kg respectively.

SKU 8 mm: The highest reported Body and Simultaneous SAR values are: 0.76 W/kg and 1.57 W/kg respectively.

SKU 11mm: The highest reported Body and Simultaneous SAR values are: 0.80 W/kg and 1.59 W/kg respectively.

This filing meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference antenna(s): PIFA reference antenna (2.95 dBi), Dipole reference antenna (2.95 dBi) and Monopole reference antenna (2.83 dBi).

SAR testing was performed to demonstrate portable RF compliance for the PIFA antenna for each distance/SKU. This module is approved in portable configurations with PIFA reference antenna (2.95 dBi). For 40mm SKU: The highest reported Body and Simultaneous SAR values are 0.31 W/kg and 1.55 W/kg respectively. This filing meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference antenna(s): PIFA reference antenna (2.95 dBi), Dipole reference antenna (2.95 dBi) and Monopole reference antenna (2.83 dBi).

This C2PC filing establishes portable category for ASUS platform with models: B5406FMA and B5456FMA, with permanently adjusting the power through BIOS that cannot be changeable by the end-users. SAR measurement was performed to demonstrate RF Exposure compliance. The highest reported Body and Simultaneous SAR values are 1.16 W/kg and 1.59 W/kg, respectively. Antennas used - PIFA with Part numbers: RAN01RY7200001 (main and aux) manufactured by Luxshare; and RAN01RY7200002 (main and aux) manufactured by AWAN. This device contains 2.4GHz BT and 5GHz/6GHz WLAN transmitters.

Power Output listed is conducted. Modular Approval filing. This device contains a 2 x 2 MIMO configuration. The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. Grantee must provide installation and operating instructions for complying with FCC multi-transmitter product procedures. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter. End-users and installers must be provided with transmitter operating conditions for satisfying RF exposure compliance.

SAR testing was performed to demonstrate portable RF compliance for the PIFA antenna for each distance/SKU. This module is approved in portable configurations with PIFA reference antenna (2.95 dBi).

For 40mm SKU: The highest reported Body and Simultaneous SAR values are 0.07 W/kg and 1.55 W/kg respectively.

The additional SKU/power profiles determine conditions based on modular stand-alone SAR evaluation to establish the minimum antenna to user separation distances (5mm, 8mm and 11mm) at a maximum SAR value less than 0.8W/kg(1g) for mixed mobile/portable conditions according to KDB 447498 D01 General RF Exposure Guidance v06 and KDB 616217 D04 for Laptop and Tablets v01.

SKU 5 mm: The highest reported Body and Simultaneous SAR values are: 0.75 W/kg and 1.44 W/kg respectively.

SKU 8 mm: The highest reported Body and Simultaneous SAR values are: 0.71 W/kg and 1.57 W/kg respectively.

SKU 11mm: The highest reported Body and Simultaneous SAR values are: 0.43 W/kg and 1.59 W/kg respectively.

This filing meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference antenna(s): PIFA reference antenna (2.95 dBi), Dipole reference antenna (2.95 dBi) and Monopole reference antenna (2.83 dBi).

SAR testing was performed to demonstrate portable RF compliance for the PIFA antenna for each distance/SKU. This module is approved in portable configurations with PIFA reference antenna (5.11 to 5.15 dBi). For 40mm SKU: The highest reported Body and Simultaneous SAR values are 0.79 W/kg and 1.55 W/kg respectively. This filing meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference antenna(s): PIFA reference antenna (5.11 to 5.15 dBi), Dipole reference antenna (4.03 to 5.15 dBi) and Monopole reference antenna (4.43 to 4.95 dBi).

This C2PC filing establishes portable category for ASUS platform with models: B5406FMA and B5456FMA, with permanently adjusting the power through BIOS that cannot be changeable by the end-users. SAR measurement was performed to demonstrate RF Exposure compliance. The highest reported Body and Simultaneous SAR values are 1.2 W/kg and 1.59 W/kg, respectively. Antennas used - PIFA with Part numbers: RAN01RY7200001 (main and aux) manufactured by Luxshare; and RAN01RY7200002 (main and aux) manufactured by AWAN. This device contains 2.4GHz BT/BLE/WLAN and 6GHz WLAN transmitters.

Power Density and SAR testing was performed to demonstrate portable RF compliance for the PIFA antenna for each distance/SKU. This module is approved in portable configurations with PIFA reference antenna (4.88 to 5.02 dBi). For 40mm SKU: The highest reported Body and Simultaneous SAR values are 0.68 W/kg and 1.55 W/kg respectively. This filing meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference antennas: PIFA reference antenna (4.88 to 5.02 dBi), Dipole reference antenna (4.49 to 5.02 dBi) and Monopole reference antenna (4.79 to 4.91 dBi). The minimum gain approved with the UNII-5 to UNII-8 bands is -2.0 dBi.

This C2PC filing establishes portable category for ASUS platform with models: B5406FMA and B5456FMA, with permanently adjusting the power through BIOS that cannot be changeable by the end-users. SAR measurement was performed to demonstrate RF Exposure compliance. The highest reported Body and Simultaneous SAR values are 1.19 W/kg and 1.59 W/kg, respectively. The highest reported power density is 5.8 W/m2. Antennas used - PIFA with Part numbers: RAN01RY7200001 (main and aux) manufactured by Luxshare; and RAN01RY7200002 (main and aux) manufactured by AWAN. This device contains 2.4GHz BT/BLE/WLAN and 5GHz WLAN transmitters.

Power Density and SAR testing was performed to demonstrate portable RF compliance for the PIFA antenna for each distance/SKU. This module is approved in portable configurations with PIFA reference antenna (4.88 to 5.02 dBi). For 40mm SKU: The highest reported Body and Simultaneous SAR values are 0.68 W/kg and 1.55 W/kg respectively. This filing meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference This filing meets MPE requirements of KDB 447498 an antenna(s): PIFA reference antenna (4.88 to 5.02 dBi), Dipole reference antenna (4.49 to 5.02 dBi) and Monopole reference antenna (4.79 to 4.91 dBi). The minimum gain approved with the UNII-5 to UNII-8 bands is -2.0 dBi.

This C2PC filing establishes portable category for ASUS platform with models: B5406FMA and B5456FMA, with permanently adjusting the power through BIOS that cannot be changeable by the end-users. SAR measurement was performed to demonstrate RF Exposure compliance. The highest reported Body and Simultaneous SAR values are 1.19 W/kg and 1.59 W/kg, respectively. The highest reported power density is 5.8 W/m2. Antennas used - PIFA with Part numbers: RAN01RY7200001 (main and aux) manufactured by Luxshare; and RAN01RY7200002 (main and aux) manufactured by AWAN. This device contains 2.4GHz BT/BLE/WLAN and 5GHz WLAN transmitters.