FCC ID N7NRC76B

This device is to be used only for mobile and fixed application; and must not be colocated or operating in conjunction with any other antenna or transmitter, except in accordance with FCC multi- transmitter evaluation procedures as documented in this filing. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. OEM integrators must insure that the end user has no manual instructions to remove or install this module. For mobile operating configurations the antenna gain, including cable loss, must not exceed the gains documented in this filing for, as defined in 2.1091 for satisfying RF exposure compliance. Under no conditions may an antenna gain be used that would exceed the ERP and/or EIRP power limits as specified in Part 22/24/27/90. The Grantee is responsible for providing the documentation required for modular use. This module can only be used with a host antenna circuit trace layout design in strict compliance with the OEM instructions provided.

This device has 1.4 MHz, 3 MHz, 5 MHz, 10 MHz, 15 MHz and 20 MHz bandwidth modes for LTE Bands 2/4/25/66; 1.4 MHz, 3 MHz, 5 MHz and 10 MHz bandwidth modes for LTE Bands 5/12; 1.4 MHz, 3 MHz, 5 MHz, 10 MHz and 15 MHz bandwidth modes for LTE Band 26 (824-849 MHz, up to 10 MHz only for 814-824 MHz); 5 MHz and 10 MHz bandwidth modes for LTE Bands 13/14; 5 MHz, 10MHz, 15 MHz and 20 MHz bandwidth modes for LTE Bands 71.

C2PC Application for adding FCC Rule Part 25 supplemental coverage from space (SCS) capability without any hardware or software changes.

This device is to be used only for mobile and fixed application; and must not be co-located or operating in conjunction with any other antenna or transmitter, except in accordance with FCC multi- transmitter evaluation procedures as documented in this filing. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. OEM integrators must insure that the end user has no manual instructions to remove or install this module. For mobile operating configurations the antenna gain, including cable loss, must not exceed the gains documented in this filing for, as defined in 2.1091 for satisfying RF exposure compliance. Under no conditions may an antenna gain be used that would exceed the ERP and/or EIRP power limits as specified in Part 22/24/27/90. The Grantee is responsible for providing the documentation required for modular use. This module can only be used with a host antenna circuit trace layout design in strict compliance with the OEM instructions provided.

This device has 1.4 MHz, 3 MHz, 5 MHz, 10 MHz, 15 MHz and 20 MHz bandwidth modes for LTE Bands 2/4/25/66; 1.4 MHz, 3 MHz, 5 MHz and 10 MHz bandwidth modes for LTE Bands 5/12; 1.4 MHz, 3 MHz, 5 MHz, 10 MHz and 15 MHz bandwidth modes for LTE Band 26 (824-849 MHz, up to 10 MHz only for 814-824 MHz); 5 MHz and 10 MHz bandwidth modes for LTE Bands 13/14; 5 MHz, 10MHz, 15 MHz and 20 MHz bandwidth modes for LTE Bands 71.

This device is to be used only for mobile and fixed application; and must not be co-located or operating in conjunction with any other antenna or transmitter, except in accordance with FCC multi- transmitter evaluation procedures as documented in this filing. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. OEM integrators must insure that the end user has no manual instructions to remove or install this module. For mobile operating configurations the antenna gain, including cable loss, must not exceed the gains documented in this filing for, as defined in 2.1091 for satisfying RF exposure compliance. Under no conditions may an antenna gain be used that would exceed the ERP and/or EIRP power limits as specified in Part 22/24/27/90. The Grantee is responsible for providing the documentation required for modular use. This module can only be used with a host antenna circuit trace layout design in strict compliance with the OEM instructions provided.

This device has 1.4 MHz, 3 MHz, 5 MHz, 10 MHz, 15 MHz and 20 MHz bandwidth modes for LTE Bands 2/4/25/66; 1.4 MHz, 3 MHz, 5 MHz and 10 MHz bandwidth modes for LTE Bands 5/12; 1.4 MHz, 3 MHz, 5 MHz, 10 MHz and 15 MHz bandwidth modes for LTE Band 26 (824-849 MHz, up to 10 MHz only for 814-824 MHz); 5 MHz and 10 MHz bandwidth modes for LTE Bands 13/14; 5 MHz, 10MHz, 15 MHz and 20 MHz bandwidth modes for LTE Bands 71.

This device is to be used only for mobile and fixed application; and must not be colocated or operating in conjunction with any other antenna or transmitter, except in accordance with FCC multi- transmitter evaluation procedures as documented in this filing. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. OEM integrators must insure that the end user has no manual instructions to remove or install this module. For mobile operating configurations the antenna gain, including cable loss, must not exceed the gains documented in this filing for, as defined in 2.1091 for satisfying RF exposure compliance. Under no conditions may an antenna gain be used that would exceed the ERP and/or EIRP power limits as specified in Part 22/24/27/90. The Grantee is responsible for providing the documentation required for modular use. This module can only be used with a host antenna circuit trace layout design in strict compliance with the OEM instructions provided.

This device has 1.4 MHz, 3 MHz, 5 MHz, 10 MHz, 15 MHz and 20 MHz bandwidth modes for LTE Bands 2/4/25/66; 1.4 MHz, 3 MHz, 5 MHz and 10 MHz bandwidth modes for LTE Bands 5/12; 1.4 MHz, 3 MHz, 5 MHz, 10 MHz and 15 MHz bandwidth modes for LTE Band 26 (824-849 MHz, up to 10 MHz only for 814-824 MHz); 5 MHz and 10 MHz bandwidth modes for LTE Bands 13/14; 5 MHz, 10MHz, 15 MHz and 20 MHz bandwidth modes for LTE Bands 71.

C2PC Application for adding FCC Rule Part 25 supplemental coverage from space (SCS) capability without any hardware or software changes.

Class II Permissive Change: Add new models of RC7611-1, RC7611D and RC7611D-1; Pin-to-pin-compatible replacement of the duplexer, RF PA module IC, SP8T switch, coupler, and SAW filter, along with a firmware update to improve performance.