FCC ID PWO274080
iDEN 800MHz Signal Booster
by Wilson Electronics, LLC
Grantee Code: PWO Product Code: 274080
Latest application date: 2012-05-24
FCC ID Device Details
| FCC ID | PWO274080 |
|---|---|
| Mirrors | fcc.id | gov | fccid.ai |
| Grantee Code | PWO |
| Product Code | 274080 |
| Applicant Business | Wilson Electronics, LLC 🇺🇸 |
| Related Domains |  wilsonelectronics.com |
| Equipment Class | iDEN 800MHz Signal Booster |
| Test Firm | Bay Area Compliance Laboratory |
Operating Frequencies
| Frequency Range | Application Purpose | Final Action Date |
|---|---|---|
| 806-824 MHz | Original Equipment | 2012-05-24 |
Exhibits
| Document | Type | Available | File |
|---|---|---|---|
| Users Manual | Users Manual | 2012-05-24 | PDF 1 MB |
| Internal Photos | Internal Photos | 2012-05-24 | PDF 358.7 KB |
| External Photos | External Photos | 2012-05-24 | PDF 206.6 KB |
| FCC ID Label | ID Label/Location Info | 2012-05-24 | PDF 28.9 KB |
| Test Setup Photos | Test Setup Photos | 2012-05-24 | PDF 310.9 KB |
| Test Report | Test Report | 2012-05-24 | PDF 1.3 MB |
| Confidential Request Letter | Cover Letter(s) | 2012-05-24 | PDF 120.9 KB |
| RF Exposure Information | RF Exposure Info | 2012-05-24 | PDF 685.3 KB |
Application Information
| Application ID | cUQJUzeengsQE56qmZwEeQ== |
|---|---|
| Final Action Date | 2012-05-24 |
| Application Purpose | Original Equipment |
| Applicant FRN | 0017528332 |
| Model | 274080 |
| Frequency Range | 806-824 MHz |
| Equipment Class | TNB - Licensed Non-Broadcast Station Transmitter |
| Device Description | iDEN 800MHz Signal Booster |
| Responsible Party | Erin C. Elder, IP and Certification Engineer, eelder@wilsonelectronics.com , 435-673-5021 |
| Test Firm | John Chan, Bay Area Compliance Laboratory, bacl.regulatory@baclcorp.com  , 408-732-9162 |
| TCB Email | bacl.regulatory@baclcorp.com |
| TCB Scope | B2: General Mobile Radio And Broadcast Services equipment in the following 47 CFR Parts 22 (non-cellular) 73, 74, 90, 95 & 97 |
| Short-Term Confidentiality | No |
| Long-Term Confidentiality | Yes |
| Grant Deferral | No |
| Modular Equipment | Does not apply |
| Composite Device | No |
| Composite Part | No |
| Cognitive Radio | No |
| Authorization Waiver | No |
| Authorization Waiver Approved | No |
| Section 5301 Certification | Yes |
| Related OET Knowledge DataBase Inquiry | No |
| Grant Comments | Power listed is conducted. The antenna installation and operating configurations of this transmitter, including any applicable source-based time-averaging duty factor, antenna gain and cable loss must satisfy MPE categorical exclusion requirements of §2.1091. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm for the inside antenna and 120 cm for the outside antenna from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Antenna gain less cable loss must not exceed 15 dBi for the outside antenna or 6.9 dBi for the inside antenna. Users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. NOTE 1: F3E, F1D, D7W, GXW |
Applications
| Application ID | Date | Purpose |
|---|---|---|
| cUQJUzeengsQE56qmZwEeQ== | 2012-05-24 | Original Equipment |
Equipment Authorization
Grants
TCB Grant - Application cUQJUzeengsQE56qmZwEeQ==
| TCB | GRANT OF EQUIPMENT AUTHORIZATION |
TCB |
| Certification | ||
| Issued Under the Authority of the | ||
| Federal Communications Commission | ||
| By: |
|
Bay Area Compliance Laboratory Corp. 1274 Anvilwood Avenue Sunnyvale, CA 94089 |
Date of Grant: 05/24/2012 Application Dated: 05/24/2012 |
| Wilson Electronics, LLC |
| 3301 E. Deseret Drive |
| St. George, UT 84790 |
| Attention: Erin Elder , IP and Certification Engineer |
| NOT TRANSFERABLE |
| EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below. |
| FCC IDENTIFIER: | PWO274080 |
| Name of Grantee: | Wilson Electronics, LLC |
| Equipment Class: | Licensed Non-Broadcast Station Transmitter |
| Notes: | iDEN 800MHz Signal Booster |
| Grant Notes | FCC Rule Parts | Frequency Range (MHZ) | Output Watts | Frequency Tolerance | Emission Designator |
| 90 | 806.0 - 824.0 | 3.02 | Amp | NOTE 1 | |
| 90 | 851.0 - 869.0 | 0.491 | Amp | NOTE 1 |
| Power listed is conducted. The antenna installation and operating configurations of this transmitter, including any applicable source-based time-averaging duty factor, antenna gain and cable loss must satisfy MPE categorical exclusion requirements of §2.1091. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm for the inside antenna and 120 cm for the outside antenna from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Antenna gain less cable loss must not exceed 15 dBi for the outside antenna or 6.9 dBi for the inside antenna. Users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. NOTE 1: F3E, F1D, D7W, GXW |
EAS Grant - Application cUQJUzeengsQE56qmZwEeQ==
| COPY |
FEDERAL COMMUNICATIONS COMMISSION WASHINGTON, D.C. 20554 GRANT OF EQUIPMENT AUTHORIZATION |
COPY |
| Certification |
|
Wilson Electronics, LLC 3301 E. Deseret Drive St. George, UT 84790 United States |
Date of Grant: 05/24/2012 Application Dated: 05/24/2012 |
| Attention: Erin Elder , IP and Certification Engineer |
| NOT TRANSFERABLE |
| EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below. |
| FCC IDENTIFIER: | PWO274080 |
| Name of Grantee: | Wilson Electronics, LLC |
| Equipment Class: | Licensed Non-Broadcast Station Transmitter |
| Notes: | iDEN 800MHz Signal Booster |
| Modular Type: | Does not apply |
| Grant Notes | FCC Rule Parts | Frequency Range (MHZ) | Output Watts | Frequency Tolerance | Emission Designator |
| 90 | 806.0 - 824.0 | 3.02 | Amp | NOTE 1 | |
| 90 | 851.0 - 869.0 | 0.491 | Amp | NOTE 1 |
| Power listed is conducted. The antenna installation and operating configurations of this transmitter, including any applicable source-based time-averaging duty factor, antenna gain and cable loss must satisfy MPE categorical exclusion requirements of §2.1091. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm for the inside antenna and 120 cm for the outside antenna from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Antenna gain less cable loss must not exceed 15 dBi for the outside antenna or 6.9 dBi for the inside antenna. Users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. NOTE 1: F3E, F1D, D7W, GXW |
| Mail To: |