1. FCC ID
  2. PY3
  3. PY3HE102

FCC ID PY3HE102

Wireless Access Point Module

by Netgear Incorporated

Grantee Code: PY3   Product Code: HE102
Latest application date: 2001-12-18

FCC ID Device Details

FCC IDPY3HE102
Mirrorsfcc.id | gov | fccid.ai
Grantee CodePY3
Product CodeHE102
Applicant BusinessNetgear Incorporated 🇺🇸
Related Domains netgear.com
Equipment ClassWireless Access Point Module
Test FirmElliott Laboratories LLC

Operating Frequencies

Frequency RangeApplication PurposeFinal Action Date
5150-5250 MHzOriginal Equipment2001-12-18

Exhibits

DocumentTypeAvailableFile
ManualUsers Manual2001-12-18PDF 3.9 MB
Internal PhotosInternal Photos2001-12-18PDF 378.9 KB
External PhotosExternal Photos2001-12-18PDF 94.2 KB
Revised Label and LocationID Label/Location Info2001-12-18PDF 351.3 KB
Test Config PhotosTest Setup Photos2001-12-18PDF 237.3 KB
Test ReportTest Report2001-12-18PDF 1.1 MB
ATCB Comments 11282001Cover Letter(s)2001-12-18PDF 13.5 KB
Confid RequestCover Letter(s)2001-12-18PDF 25 KB
Letter of AuthorityCover Letter(s)2001-12-18PDF 24.5 KB
Modular Approval ChecklistCover Letter(s)2001-12-18PDF 64.8 KB
Response to ATCBCover Letter(s)2001-12-18PDF 30.2 KB
MPE CalculationsRF Exposure Info2001-12-18PDF 9.8 KB
Block Diag Metadata onlyBlock DiagramPDF 69.4 KB
Schema Metadata onlySchematicsPDF 326.4 KB
Theory of Ops Metadata onlyOperational DescriptionPDF 29.2 KB

Application Information

Application IDii9GiJKmE/B/wEdZDI8P7Q==
Final Action Date2001-12-18
Application PurposeOriginal Equipment
Applicant FRN0022158786
ModelHE102
Frequency Range5150-5250 MHz
Equipment ClassNII - Unlicensed National Information Infrastructure TX
Device DescriptionWireless Access Point Module
Responsible PartyDavid Kay, david.kay@netgear.com , 4088903160
AgentJuan Juan Juan, Elliott Laboratories, Inc., doc@elliottlabs.com , 408 245 7800
Technical ContactJuan Martinez, Elliott Laboratories, Inc., doc@elliottlabs.com , 408 245 7800
Test FirmDavid Bare, Elliott Laboratories LLC, dbare@elliottlabs.com , 408-245-7800
TCB Emailhotline@americanTCB.com
TCB ScopeA4: UNII devices & low power transmitters using spread spectrum techniques
Short-Term ConfidentialityNo
Long-Term ConfidentialityYes
Grant DeferralNo
Modular EquipmentDoes not apply
Composite DeviceNo
Composite PartNo
Cognitive RadioNo
Authorization WaiverNo
Authorization Waiver ApprovedNo
Section 5301 CertificationYes
Related OET Knowledge DataBase InquiryNo
Grant CommentsModule Approval. Power Output listed is Conducted. The installation and operating configurations of this transmitter, including the antenna gain and cable loss, must satisfy MPE Categorical Exclusion Requirements of §2.1091. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Installers and end-users must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.

Applications

Application IDDatePurpose
ii9GiJKmE/B/wEdZDI8P7Q==2001-12-18Original Equipment

Equipment Authorization

FrequencyOutputRules
5150-5250 MHz0.03515E
5250-5350 MHz0.09115E

Grants

TCB Grant - Application ii9GiJKmE/B/wEdZDI8P7Q==

TCB GRANT OF EQUIPMENT
AUTHORIZATION		 TCB
Certification
Issued Under the Authority of the
Federal Communications Commission
By:

  ACB, Inc.
6731 Whittier Avenue Suite C110
McLean, VA 22101
 Date of Grant: 12/18/2001

Application Dated: 12/18/2001
Netgear Incorporated
350 East Plumeria Drive
San Jose, CA 95134
 
Attention: David Kay

NOT TRANSFERABLE
EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below.
 
FCC IDENTIFIER:  PY3HE102
Name of Grantee:  Netgear Incorporated
Equipment Class: Unlicensed National Information Infrastructure TX
Notes: Wireless Access Point Module
Grant Notes  FCC Rule Parts Frequency
Range (MHZ) 		Output
Watts 		Frequency
Tolerance 		Emission
Designator
15E 5150.0  -  5250.0 0.035  
15E 5250.0  -  5350.0 0.091  

Module Approval. Power Output listed is Conducted. The installation and operating configurations of this transmitter, including the antenna gain and cable loss, must satisfy MPE Categorical Exclusion Requirements of §2.1091. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Installers and end-users must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.

EAS Grant - Application ii9GiJKmE/B/wEdZDI8P7Q==

COPY FEDERAL COMMUNICATIONS
COMMISSION
WASHINGTON, D.C. 20554

GRANT OF EQUIPMENT
AUTHORIZATION		 COPY
Certification

Netgear Incorporated
350 East Plumeria Drive
San Jose, CA 95134
United States 		  Date of Grant: 12/18/2001

Application Dated: 12/18/2001
 
Attention: David Kay

NOT TRANSFERABLE
EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below.
 
FCC IDENTIFIER:  PY3HE102
Name of Grantee:  Netgear Incorporated
Equipment Class: Unlicensed National Information Infrastructure TX
Notes: Wireless Access Point Module
Modular Type: Does not apply
Grant Notes  FCC Rule Parts Frequency
Range (MHZ) 		Output
Watts 		Frequency
Tolerance 		Emission
Designator
15E 5150.0  -  5250.0 0.035  
15E 5250.0  -  5350.0 0.091  

Module Approval. Power Output listed is Conducted. The installation and operating configurations of this transmitter, including the antenna gain and cable loss, must satisfy MPE Categorical Exclusion Requirements of §2.1091. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Installers and end-users must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.



Mail To: