11 Blue Gecko BGM11SxA/BGM11xN Bluetooth Smart Module Cover Letter Modular approval request letter_v2 Silicon Laboratories Finland Oy

Silicon Laboratories Finland Oy Blue Gecko BGM11SxA/BGM11xN Bluetooth Smart Module

Page 1 of 11 Blue Gecko BGM11SxA/BGM11xN Bluetooth Smart Module Cover Letter Modular approval request letter_v2 Silicon Laboratories Finland Oy
Page 2 of 11 Blue Gecko BGM11SxA/BGM11xN Bluetooth Smart Module Cover Letter Modular approval request letter_v2 Silicon Laboratories Finland Oy
Page 3 of 11 Blue Gecko BGM11SxA/BGM11xN Bluetooth Smart Module Cover Letter Modular approval request letter_v2 Silicon Laboratories Finland Oy
Page 4 of 11 Blue Gecko BGM11SxA/BGM11xN Bluetooth Smart Module Cover Letter Modular approval request letter_v2 Silicon Laboratories Finland Oy

S | Li E El N LA B S
MODULAR APPROVAL REQUEST
13.4.2017
FIE: FCC Modular Approval
FCC ID: 0001 1
Dear Application Examiner
Bluegiga Technologies Inc. / Bluetooth module, FCC ID: 00011, would like to have your
authorization as a modular approval. The requirements of section 15.212 of FCC rules have
been met and shown on the following statements.
REQUIREMENT Yes / No
The modular transmitter YES
must have its own FiF
shielding.
COMMENT
The module has a shield
The module has buffered data inputs
integrated to EFFl32 chip
The modular transmitter YES
must have buffered
modulation/data inputs (it
such inputs are provided)
to ensure that the module
will comply with Part 15
requirements under
conditions of excessive
data rates or over-
modulation.
The modular transmitter YES The module has Its own power supply
must have its own power regulation.
supply regulation.
The modular transmitter YES An embedded chip antenna is
must comply with the permanently attached to the BGM11S1A
antenna requirements of and BGM1182A.
Section 15.203 and
15.204(c). The antenna
must either be
permanently attached or
employ a “unique"
antenna coupler (at all
connections between the
module and the antenna,
including the cable). Any
antenna used with the
module must be approved
with the module, either at
the
anal .mgm gum 1
time of initial authorization
or through a Class II
permissive change. The
“professional installation“
provision of Section
15.203 may not be
applied to modules.
The modular transmitter
must be tested in a stand-
alone contiguration, i,e.,
the module must not be
inside another device
during testing. This is
Intended to demonstrate
that the module is capable
of complyan with Part 15
emission limits regardless
of the device into which it
Is eventually installed.
Unless the ransmitter
module will be battery
powered, it must comply
with the AC line
conducted requirements
lound in Section 15.207.
AC or DC power lines and
data input/output lines
connected to the module
must not contain territes,
unless they will be
marketed with the module
(see Section 15.27(a)).
The length of these lines
shall be length typical of
actual use or, it that length
ls unknown, at least 10
centimeters
to insure that there is no
coupling between the
case of the module and
supporting equipment.
Any accessories,
peripherals, or support
equipment connected to
the module during testing
shall be unmodified or
commercially available
see Section 15.31 i .
The modular transmitter
must be labeled with its
own FCC ID number, and,
it the FCC ID Is not vislble
when the module is
installed Inslde another
configuration using a test kit,
The module is labeled with its own FCC
ID number
The module was tested in a standalone
device, then the outside of
the device into which the
module is installed must
also display a label
referring to the enclosed
module. This exterior label
can use wording such as
the following: “Contains
Transmitter
Module FCC ID:
XYZMODEL1’l or
“Contains FCC ID:
XYZMODEL1.” Any
similar wording that
expresses the same
meaning may be used.
The Grantee may either
provide such a label, an
example of which must be
included in the application
for equipment
authorization, or, must
provide adequate
instructions along with the
module which explain this
requirement. In the latter
case, a copy of these
instructions must be
included in the
application for equipment
authorization.
The modular transmitter
must comply with any
specific rule or operating
requirements applicable to
the transmitter and the
manufacturer must
provide adequate
Instructions along with the
module to explain any
such requirements A
copy of these instructions
must be
included in the application
for equipment
authorization. For
example, there are very
strict operational and
timing requirements that
must be met before a
transmitter is authorized
for operation under
Section 15231. For
instance, data
YES
The module ls compliant with all
applicable FCC rules. Detailed
instructions for remaining compliance are
given in the User Manual (datasheet).
transmission is prohibited,
except for operation under
Sectlon 15.231 (e), in
which case there are
separate field strength
level and timing
requlrements. Compliance
wlth these requlrements
must be assmed.
The modular transmltter
must comply with any
applicable FtF exposure
requirements. For
example, FCC Rules in
Sections 2.1091, 2.1093
and specific Sections of
Part 15, including
15.3190), 15.4070),
15.2530) and 15.255(g),
require that Unlicensed
PCS, UNII and
millimeter wave devices
perform routlne
environmental evaluation
for RF exposure to
demonstrate compliance.
In additlon, spread
spectrum transmitters
operating under Section
15.247 are required to
address RF Exposure
compliance in accordance
with Section
15.247(b)(4). Modular
transmitters approved
under other Sections oi
Part 15, when necessary,
may also need to address
certain RF Exposure
concerns. typlcally by
providing specitlc
installation and operating
instructions for users,
installers and other
interested parties to
ensure compliance.
YES
The module complies with RF exposure
requirement. FtF exposure is addressed in
the HF exposure exhibition.
Best regards
65.
Pasi Rahikkala, Stat! HW Englneer
Silicon Labs
Download: 11 Blue Gecko BGM11SxA/BGM11xN Bluetooth Smart Module Cover Letter Modular approval request letter_v2 Silicon Laboratories Finland Oy
Mirror Download [FCC.gov]11 Blue Gecko BGM11SxA/BGM11xN Bluetooth Smart Module Cover Letter Modular approval request letter_v2 Silicon Laboratories Finland Oy
Document ID3425219
Application IDuMX4C33pe/wjX2uIqcnR/Q==
Document DescriptionModular approval request letter_v2
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeCover Letter(s)
Display FormatAdobe Acrobat PDF - pdf
Filesize11.48kB (143561 bits)
Date Submitted2017-06-14 00:00:00
Date Available2017-06-14 00:00:00
Creation Date2017-04-13 10:27:31
Producing SoftwareXerox WorkCentre 7835
Document Lastmod2017-04-13 10:33:05
Document TitleModular approval request letter_v2
Document CreatorXerox WorkCentre 7835

Source Exif Data [exif.tools]:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Create Date                     : 2017:04:13 10:27:31+02:00
Creator                         : Xerox WorkCentre 7835
Modify Date                     : 2017:04:13 10:33:05+03:00
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Creator Tool                    : Xerox WorkCentre 7835
Metadata Date                   : 2017:04:13 10:33:05+03:00
Producer                        : Xerox WorkCentre 7835
Document ID                     : uuid:5f6f0ccc-a199-4a33-994b-d93dedf9420a
Instance ID                     : uuid:1f589182-f790-4980-8273-9d4ee31580af
Format                          : application/pdf
Page Count                      : 4