AZUMIAKARU55Q Mobile phone Test Report EMC TRF Template Azumi S.A

Azumi S.A Mobile phone

FCC ID Filing: QRP-AZUMIAKARU55Q
Purchase on Amazon: Mobile phone

Trouble Viewing? See the or view the HTML Version or PDF in frame
Page 1 of AZUMIAKARU55Q Mobile phone Test Report EMC TRF Template Azumi S.A
Page 2 of AZUMIAKARU55Q Mobile phone Test Report EMC TRF Template Azumi S.A
Page 3 of AZUMIAKARU55Q Mobile phone Test Report EMC TRF Template Azumi S.A
Page 4 of AZUMIAKARU55Q Mobile phone Test Report EMC TRF Template Azumi S.A
Page 5 of AZUMIAKARU55Q Mobile phone Test Report EMC TRF Template Azumi S.A
Page 6 of AZUMIAKARU55Q Mobile phone Test Report EMC TRF Template Azumi S.A
Page 7 of AZUMIAKARU55Q Mobile phone Test Report EMC TRF Template Azumi S.A
Page 8 of AZUMIAKARU55Q Mobile phone Test Report EMC TRF Template Azumi S.A
Page 9 of AZUMIAKARU55Q Mobile phone Test Report EMC TRF Template Azumi S.A
Page 10 of AZUMIAKARU55Q Mobile phone Test Report EMC TRF Template Azumi S.A
Page 11 of AZUMIAKARU55Q Mobile phone Test Report EMC TRF Template Azumi S.A
Page 12 of AZUMIAKARU55Q Mobile phone Test Report EMC TRF Template Azumi S.A
Page 13 of AZUMIAKARU55Q Mobile phone Test Report EMC TRF Template Azumi S.A
Page 14 of AZUMIAKARU55Q Mobile phone Test Report EMC TRF Template Azumi S.A
Page 15 of AZUMIAKARU55Q Mobile phone Test Report EMC TRF Template Azumi S.A
Page 16 of AZUMIAKARU55Q Mobile phone Test Report EMC TRF Template Azumi S.A
Page 17 of AZUMIAKARU55Q Mobile phone Test Report EMC TRF Template Azumi S.A
Page 18 of AZUMIAKARU55Q Mobile phone Test Report EMC TRF Template Azumi S.A
Page 19 of AZUMIAKARU55Q Mobile phone Test Report EMC TRF Template Azumi S.A
Page 20 of AZUMIAKARU55Q Mobile phone Test Report EMC TRF Template Azumi S.A
Page 21 of AZUMIAKARU55Q Mobile phone Test Report EMC TRF Template Azumi S.A
Page 22 of AZUMIAKARU55Q Mobile phone Test Report EMC TRF Template Azumi S.A
Page 23 of AZUMIAKARU55Q Mobile phone Test Report EMC TRF Template Azumi S.A
Page 24 of AZUMIAKARU55Q Mobile phone Test Report EMC TRF Template Azumi S.A
Page 25 of AZUMIAKARU55Q Mobile phone Test Report EMC TRF Template Azumi S.A
Page 26 of AZUMIAKARU55Q Mobile phone Test Report EMC TRF Template Azumi S.A
Page 27 of AZUMIAKARU55Q Mobile phone Test Report EMC TRF Template Azumi S.A
Page 28 of AZUMIAKARU55Q Mobile phone Test Report EMC TRF Template Azumi S.A
Page 29 of AZUMIAKARU55Q Mobile phone Test Report EMC TRF Template Azumi S.A
Page 30 of AZUMIAKARU55Q Mobile phone Test Report EMC TRF Template Azumi S.A
Page 31 of AZUMIAKARU55Q Mobile phone Test Report EMC TRF Template Azumi S.A

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QRP-AZUMIAKARU55Q Report No.: LCS170329088AE
FCC PART 22/24 TEST REPORT
FCC Part 22 /Part 24
Report Reference No. ................... : LCS170329088AE
FCC ID. .......................................... : QRP-AZUMIAKARU55Q
Date of Issue. ................................ : May 24, 2017
Testing Laboratory Name ............. : Shenzhen LCS Compliance Testing Laboratory Ltd.
Address .......................................... : 1/F., Xingyuan Industrial Park, Tongda Road, Bao'an Avenue, Bao'an
District, Shenzhen, Guangdong, China
Applicant’s name .......................... : AZUMI S.A
Address .......................................... : Avenida Aquilino de la Guardia con Calle 47, PH Ocean Plaza, Piso
16 of. 16-01, Marbella, Ciudad de Panama
Test specification.......................... :
Standard ......................................... :
FCC Part 22: Public Mobile Services
FCC Part 24: Personal Communication Services
Test Report Form No ..................... : LCSEMC-1.0
TRF Originator ................................ : Shenzhen LCS Compliance Testing Laboratory Ltd.
Master TRF..................................... : Dated 2011-03
Shenzhen LCS Compliance Testing Laboratory Ltd. All rights reserved.
This publication may be reproduced in whole or in part for non-commercial purposes as long as the
Shenzhen LCS Compliance Testing Laboratory Ltd. is acknowledged as copyright owner and source of the
material. Shenzhen LCS Compliance Testing Laboratory Ltd. takes no responsibility for and will not assume
liability for damages resulting from the reader's interpretation of the reproduced material due to its
placement and context.
Test item description .................... : Mobile phone
Trade Mark ..................................... : AZUMI
Model/Type reference ..................... : Extend Akaru 55 QL
Listed Models ................................ : Extend Akaru 55 QL
DC 3.7V, 4000mAh
Ratings ........................................... : Charging parameter: AC Input: 100~240V, 50/60Hz, 0.3A;
Output: DC 5V, 1.5A
Modulation ..................................... : QPSK
Hardware version............................ : /
Software version ............................ : /
Frequency ...................................... : UMTS Band II /UMTS Band V
Result ............................................. : PASS
Compiled by:
Supervised by:
Approved by:
Kyle Yin/ File administrators
Glin Lu/ Technique principal
Gavin Liang/ Manager
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QRP-AZUMIAKARU55Q Report No.: LCS170329088AE
TEST REPORT
Test Report No. :
LCS170329088AE
May 24, 2017
Date of issue
______________________________________________________________________________________________
Equipment under Test
: Mobile phone
Model /Type
: Extend Akaru 55 QL
Listed Models
: Extend Akaru 55 QL
Applicant
: AZUMI S.A
Address
: Avenida Aquilino de la Guardia con Calle 47, PH Ocean Plaza, Piso
16 of. 16-01, Marbella, Ciudad de Panama
Manufacturer
: AZUMI HK LTD
Address
: FLAT/RM 18 BLK 1 14/F GOLDEN INDUSTRIAL BUILDING 16-26
KWAI TAK STREET KWAI CHUNG,HK
Factory
: LWIN HK CO.,LIMITED
Address
: Room 9C,A Zone,Shenye Tairan Hongsong building,Tairan Six
Road North,CheGongMiao, FuTian District,Shenzhen,Guangdong
Province,P.R.China
Test Result:
PASS
The test report merely corresponds to the test sample.
It is not permitted to copy extracts of these test result without the written permission of the test
laboratory.
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QRP-AZUMIAKARU55Q Report No.: LCS170329088AE
Revison History
Revision
00
Issue Date
2017-05-25
Revisions
Initial Issue
Revised By
Gavin Liang
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QRP-AZUMIAKARU55Q Report No.: LCS170329088AE
Contents
T EST ST AND ARDS ................................................................. 5
SUMM AR Y ............................................................................ 6
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
2.10
General Remarks
Product Description
Equipment under Test
Short description of the Equipment under Test (EUT)
Internal Identification of AE used during the test
Normal Accessory setting
EUT configuration
Related Submittal(s) / Grant (s)
Modifications
General Test Conditions/Configurations
T EST ENVIRONMENT .............................................................. 9
3.1
3.2
3.3
3.4
3.5
3.6
Address of the test laboratory
Test Facility
Environmental conditions
Test Description
Equipments Used during the Test
Measurement uncertainty
T EST CONDIT IONS AN D RES ULT S........................................... 13
4.1
4.2
4.3
4.4
4.5
4.6
4.7
Output Power
Radiated Spurious Emssion
Occupied Bandwidth and Emission Bandwith
Band Edge Compliance
Spurious Emssion on Antenna Port
Frequency Stability Test
Peak-to-Average Ratio (PAR)
T EST SET UP PHOT OGRAP HS OF EUT ...................................... 31
EXT ERIOR PHOTOGRAPH S OF T HE EUT ................................... 31
INT ERIOR PHOTOGRAP HS OF T HE EUT ................................... 31
11
12
13
16
19
21
23
27
29
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QRP-AZUMIAKARU55Q Report No.: LCS170329088AE
1 TEST STANDARDS
The tests were performed according to following standards:
FCC Part 22 (10-1-16 Edition): Private Land Mobile Radio Services.
FCC Part 24(10-1-16 Edition): Public Mobile Services.
TIA/EIA 603 D June 2010: Land Mobile FM or PM Communications Equipment Measurement and
Performance Standards.
47 CFR FCC Part 15 Subpart B: Unintentional Radiators.
FCC Part 2: Frequency Allocations And Radio Treaty Matters: General Rules And Regulations.
ANSI C63.4:2014: Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and
Electronic Equipment in the Range of 9 kHz to 40 GHz.
FCCKDB971168D01 Power Meas License Digital Systems
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QRP-AZUMIAKARU55Q Report No.: LCS170329088AE
2 SUMMARY
2.1
General Remarks
Date of receipt of test sample
March 29, 2017
Testing commenced on
May 24, 2017
Testing concluded on
May 24, 2017
2.2
Product Description
The AZUMI S.A’s Model: Extend Akaru 55 QL or the “EUT” as referred to in this report; more general
information as follows, for more details, refer to the user’s manual of the EUT.
Name of EUT
Model Number
Modulation Type
Antenna Gain
Hardware version
Software version
GSM/EDGE/GPRS Operation
Frequency Band
UMTS Operation Frequency Band
LTE Operation Frequency Band
GSM/EDGE/GPRS
GSM Release Version
GSM/EDGE/GPRS Power Class
GPRS/EDGE Multislot Class
GPRS operation mode
WCDMA Release Version
HSDPA Release Version
HSUPA Release Version
DC-HSUPA Release Version
LTE Release Version
LTE/UMTS Power Class
WLAN FCC Modulation Type
WLAN FCC Operation frequency
Antenna Type
BT Modulation Type
Extreme temp. Tolerance
GPS function
NFC Function
Extreme vol. Limits
Mobile phone
Extend Akaru 55 QL
GMSK for GSM/GPRS, 8-PSK for EDGE,QPSK for UMTS, QPSK,
16QAM for LTE
-1.08dBi (max.) For GSM 850; -0.6dBi (max.) For GSM 900;
-0.2dBi (max.) For DCS 1800; 0.1dBi (max.) For PCS 1900;
0.1dBi (max.) For WCDMA Band II
-1.08dBi (max.) For WCDMA Band V
0.1dBi (max.) For LTE FDD Band 2;
-0.4dBi (max.) For LTE FDD Band 4;
0.8dBi (max.) For LTE FDD Band 7;
0.5dBi (max.) For BT and WLAN
GSM850/PCS1900/GPRS850/GPRS1900/EDGE850/EDGE1900
UMTS FDD Band II/V
LTE FDD band 2, FDD band 4, FDD band 7
Supported GSM/GPRS/EDGE
R99
GSM850:Power Class 4/ PCS1900:Power Class 1
GPRS/EDGE: Multi-slot Class 12
Class B
R99
Release 10
Release 6
Not Supported
R8
Level 3
IEEE 802.11b: DSSS(CCK,DQPSK,DBPSK)
IEEE 802.11g: OFDM(64QAM, 16QAM, QPSK, BPSK)
IEEE 802.11n HT20: OFDM (64QAM, 16QAM, QPSK,BPSK)
IEEE 802.11n HT40: OFDM (64QAM, 16QAM, QPSK,BPSK)
IEEE 802.11b:2412-2462MHz
IEEE 802.11g:2412-2462MHz
IEEE 802.11n HT20:2412-2462MHz
IEEE 802.11n HT40:2422-2452MHz
Integral Antenna
GFSK,8DPSK,π/4DQPSK(BT V4.0)
-30°C to +50°C
Support and only RX
Not Support
3.40VDC to 4.2VDC (nominal: 3.70VDC)
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QRP-AZUMIAKARU55Q Report No.: LCS170329088AE
2.3
Equipment under Test
Power supply system utilised
Power supply voltage
○ 120V / 60 Hz
○ 115V / 60Hz
12
DC
○
○ 24 V DC
● Other (specified in blank below)
DC 3.70V
Test frequency list
Test Mode
TX/RX
TX
WCDMA Band V
RX
Test Mode
TX/RX
TX
WCDMA Band II
RX
2.4
Low(L)
Channel 4132
826.4 MHz
Channel 4357
871.4 MHz
Low(L)
Channel 9262
1852.4 MHz
Channel 9662
1932.4 MHz
RF Channel
Middle (M)
Channel 4183
836.6 MHz
Channel 4407
881.4 MHz
RF Channel
Middle (M)
Channel 9400
1880.0 MHz
Channel 9800
1960.0 MHz
High (H)
Channel 4233
846.6 MHz
Channel 4458
891.6 MHz
High (H)
Channel 9538
1907.6 MHz
Channel 9938
1987.6 MHz
Short description of the Equipment under Test (EUT)
2.4.1 General Description
Extend Akaru 55 QL is subscriber equipment in the WCDMA/GSM/LTE system. The HSPA/UMTS frequency
band is Band II/V, LTE frequency band is band 2, band 4, The GSM/GPRS/EDGE frequency band includes
GSM850 and GSM900 and DCS1800 and PCS1900, but only Band II and Band V and GSM850 and
PCS1900 bands test data included in this report. The Mobile phone implements such functions as RF signal
receiving/transmitting, HSPA/UMTS and GSM/GPRS/EDGE protocol processing, voice, video MMS service
and etc. Externally it provides micro SD card interface and SIM card interface.
NOTE: Unless otherwise noted in the report, the functional boards installed in the units shall be selected from
the below list, but not means all the functional boards listed below shall be installed in one unit.
2.5
Internal Identification of AE used during the test
AE ID*
AE1
AE2
Description
Battery
Charger
AE2
Model: TPA-46050150UU
INPUT: Charging parameter: AC Input: 100~240V, 50/60Hz, 0.3A;
Output: DC 5V, 1.5A
*AE ID: is used to identify the test sample in the lab internally.
2.6
Normal Accessory setting
Fully charged battery was used during the test.
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QRP-AZUMIAKARU55Q Report No.: LCS170329088AE
2.7
EUT configuration
The following peripheral devices and interface cables were connected during the measurement:
● - supplied by the manufacturer
○ - supplied by the lab
○ Power Cable
○ Multimeter
2.8
Length (m) :
Shield :
Detachable :
Manufacturer :
Model No. :
Related Submittal(s) / Grant (s)
This submittal(s) (test report) is intended for FCC ID: QRP-AZUMIAKARU55Q filing to comply with FCC Part
22 and Part 24 Rules.
2.9
Modifications
No modifications were implemented to meet testing criteria.
2.10 General Test Conditions/Configurations
2.10.1 Test Modes
NOTE: The test mode(s) are selected according to relevant radio technology specifications.
Test Mode
UMTS/TM1
UMTS/TM2
UMTS/TM3
Test Modes Description
WCDMA system, QPSK modulation
HSDPA system, QPSK modulation
HSUPA system, QPSK modulation
Note:
1. This EUT owns two SIM cards, SIM 1 support GSM/UMTS/LTE, SIM 2 only support GSM;
2. As WCDMA, HSDPA and HSUPA with the same emission designator, test result recorded in this report at
the worst case UMTS/TM1 only after exploratory scan.
2.10.2 Test Environment
Environment Parameter
Relative Humidity
Temperature
Voltage
TN
VL
VN
VH
Selected Values During Tests
Ambient
Ambient
3.40V
3.70V
4.20V
NOTE: VL=lower extreme test voltage VN=nominal voltage
VH=upper extreme test voltage TN=normal temperature
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QRP-AZUMIAKARU55Q Report No.: LCS170329088AE
3 TEST ENVIRONMENT
3.1
Address of the test laboratory
Shenzhen LCS Compliance Testing Laboratory Ltd
1/F., Xingyuan Industrial Park, Tongda Road, Bao'an Avenue, Bao'an District, Shenzhen, Guangdong,
China
The sites are constructed in conformance with the requirements of ANSI C63.4 (2014) and CISPR
Publication 22.
3.2
Test Facility
The test facility is recognized, certified, or accredited by the following organizations:
CNAS Registration Number. is L4595.
FCC Registration Number. is 899208.
Industry Canada Registration Number. is 9642A-1.
VCCI Registration Number. is C-4260 and R-3804.
ESMD Registration Number. is ARCB0108.
UL Registration Number. is 100571-492.
TUV SUD Registration Number. is SCN1081.
TUV RH Registration Number. is UA 50296516-001
3.3
Environmental conditions
During the measurement the environmental conditions were within the listed ranges:
Temperature:
15-35 °C
Humidity:
30-60 %
Atmospheric pressure:
950-1050mbar
(1)expressed at approximately the 95% confidence level using a coverage factor of k=1.96.
3.4
Test Description
3.4.1 Cellular Band (824-849MHz paired with 869-894MHz)
Test Item
Effective(Isotropic) Radiated
Output Power
Modulation Characteristics
FCC Rule No.
§2.1046,
§22.913
§2.1047
Bandwidth
§2.1049
Band Edges Compliance
§2.1051,
§22.917
Spurious Emission at
Antenna Terminals
§2.1051,
§22.917
Field Strength of Spurious
Radiation
Requirements
Verdict
FCC: ERP ≤ 7W.
Pass
Digital modulation
OBW: No limit.
EBW: No limit.
≤-13dBm/1%*EBW, in 1MHz bands
immediately outside and adjacent
to
The frequency block.
≤ -13dBm/100kHz,
from 9kHz to 10th harmonics but
outside authorized operating
frequency ranges.
N/A
§2.1053,
≤ -13dBm/100kHz.
§22.917
§2.1055,
Frequency Stability
≤ ±2.5ppm.
§22.355
Peak-Average Ratio
N/A
-Receiver Spurious Emissions
N/A
-NOTE 1: For the verdict, the “N/A” denotes “not applicable”, the “N/T” de notes “not tested”.
Pass
Pass
Pass
Pass
Pass
Pass
Pass
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QRP-AZUMIAKARU55Q Report No.: LCS170329088AE
3.4.2 PCS Band (1850-1915MHz paired with 1930-1995MHz)
Test Item
Effective(Isotropic) Radiated
Output Power
Modulation Characteristics
FCC Rule No.
§2.1046,
§24.232
§2.1046,
§24.232
§2.1047
Bandwidth
§2.1049
Band Edges Compliance
§2.1051,
§24.238
Spurious Emission at
Antenna Terminals
§2.1051,
§24.238
Peak-Average Ratio
Requirements
Verdict
EIRP ≤ 2W
Pass
≤13dB
Pass
Digital modulation
OBW: No limit.
EBW: No limit.
≤ -13dBm/1%*EBW, In 1MHz
bands immediately outside and
adjacent to The frequency
block.
≤-13dBm/1MHz, from 9kHz
to10th harmonics but outside
authorized Operating frequency
ranges.
N/A
Field Strength of Spurious
Radiation
§2.1053,
≤ -13dBm/1MHz.
§24.238
§2.1055,
Frequency Stability
≤ ±2.5ppm.
§24.235
Receiver Spurious Emissions
N/A
-NOTE 1: For the verdict, the “N/A” denotes “not applicable”, the “N/T” de notes “not tested”.
Pass
Pass
Pass
Pass
Pass
Pass
Remark: 1.The measurement uncertainty is not included in the test result.
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QRP-AZUMIAKARU55Q Report No.: LCS170329088AE
3.5
Equipments Used during the Test
Instrument
Manufacturer
Model No.
Serial No.
Characteristics
Cal Date
Due Date
EMC Receiver
R&S
ESCS 30
100174
9kHz – 2.75GHz
Jun 18, 2016
Jun 17, 2017
Signal analyzer
Agilent
US44300469
9kHz~40GHz
Jul 16, 2016
Jul 15, 2017
LISN
MESS Tec
NNB-2/16Z
99079
9KHz-30MHz
Jun 18, 2016
Jun 17, 2017
LISN
EMCO
3819/2NM
9703-1839
9KHz-30MHz
Jun 18, 2016
Jun 17, 2017
RF Cable-CON
UTIFLEX
3102-26886-4
CB049
9KHz-30MHz
Jun 18, 2016
Jun 17, 2017
ISN
SCHAFFNER
ISN ST08
21653
9KHz-30MHz
Jun 18, 2016
Jun 17, 2017
3m Semi Anechoic
SIDT
Chamber
FRANKONIA
SAC-3M
03CH03-HY
30M-18GHz
Jun 18, 2016
Jun 17, 2017
Amplifier
SCHAFFNER
COA9231A
18667
9kHz-2GHzz
Apr 18, 2016
Apr 17, 2017
Amplifier
Agilent
8449B
3008A02120
1GHz-26.5GHz
Apr 18, 2016
Apr 17, 2017
Amplifier
MITEQ
AMF-6F-260400
9121372
26.5GHz-40GHz
Apr 18, 2016
Apr 17, 2017
Loop Antenna
R&S
HFH2-Z2
860004/001
9k-30MHz
Apr 18, 2016
Apr 17, 2017
By-log Antenna
SCHWARZBECK
VULB9163
9163-470
30MHz-1GHz
Apr 18, 2016
Apr 17, 2017
Horn Antenna
EMCO
3115
6741
1GHz-18GHz
Apr 18, 2016
Apr 17, 2017
Horn Antenna
SCHWARZBECK
BBHA9170
BBHA9170154
15GHz-40GHz
Apr 18, 2016
Apr 17, 2017
RF Cable-R03m
Jye Bao
RG142
CB021
30MHz-1GHz
Jun 18, 2016
Jun 17, 2017
RF Cable-HIGH
SUHNER
SUCOFLEX 106
03CH03-HY
1GHz-40GHz
Jun 18, 2016
Jun 17, 2017
Power Meter
R&S
NRVS
100444
DC-40GHz
Jun 18, 2016
Jun 17, 2017
Power Sensor
R&S
NRV-Z51
100458
DC-30GHz
Jun 18, 2016
Jun 17, 2017
Power Sensor
R&S
NRV-Z32
10057
30MHz-6GHz
Jun 18, 2016
Jun 17, 2017
AC Power Source
HPC
HPA-500E
HPA-9100024
AC 0~300V
Jun 18, 2016
Jun 17, 2017
DC power Source
GW
GPC-6030D
C671845
DC 1V-60V
Jun 18, 2016
Jun 17, 2017
Giant Force
GTH-225-20-S
MAB0103-00
N/A
Jun 18, 2016
Jun 17, 2017
RF CABLE-1m
JYE Bao
RG142
CB034-1m
20MHz-7GHz
Jun 18, 2016
Jun 17, 2017
RF CABLE-2m
JYE Bao
RG142
CB035-2m
20MHz-1GHz
Jun 18, 2016
Jun 17, 2017
Signal Generator
R&S
SMR40
10016
10MHz~40GHz
Jul 16, 2016
Jul 15, 2017
R&S
CMU200
112012
N/A
Oct 27, 2016
Oct 26, 2017
R&S
CMW500
1201.0002K50
N/A
Nov 19, 2016
Nov 18, 2017
Agilent
N8257D
MY46520521
250KHz~20GHz
Nov 19, 2016
Nov 18, 2017
MXA Signal Analyzer
Agilent
N9020A
MY50510140
10Hz~26.5GHz
Oct 27, 2016
Oct 26, 2017
RF Control Unit
Tonscend
JS0806-1
Nov 19,2016
Nov 18, 2017
LTE Test Software
Tonscend
JS1120-1
Version: 2.5.7.0
N/A
N/A
Test Software
Ascentest
AT890-SW
20141230
Version: 20160630
N/A
N/A
NN256400424
Oct 27, 2016
Oct 26, 2017
Temp. and Humidigy
Chamber
Universal Radio
Communication Tester
Wideband Radia
Communication Tester
PSG Analog Signal
Generator
E4448A(External
mixers to 40GHz)
ZAPD-50W
4.2-
Splitter/Combiner(Qty: 2)
Mini-Circuits
Splitter/Combine(Qty: 2)
MCLI
PS3-7
4463/4464
Oct 27, 2016
Oct 26, 2017
ATT (Qty: 1)
Mini-Circuits
VAT-30+
30912
Oct 27, 2016
Oct 26, 2017
EMC Test Software
Audix
E3
6.0 GHz
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QRP-AZUMIAKARU55Q Report No.: LCS170329088AE
3.6 Measurement uncertainty
The data and results referenced in this document are true and accurate. The reader is cautioned that there
may be errors within the calibration limits of the equipment and facilities. The measurement uncertainty was
calculated for all measurements listed in this test report acc. to ETSI TR 100 028 “ Electromagnetic
compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio
equipment characteristics” and is documented in the Shenzhen LCS Compliance Testing Laboratory Ltd.
quality system acc. to DIN EN ISO/IEC 17025. Furthermore, component and process variability of devices
similar to that tested may result in additional deviation. The manufacturer has the sole responsibility of
continued compliance of the device.
Hereafter the best measurement capability for Shenzhen LCS Compliance Testing Laboratory Ltd. is reported:
Test
Radiated Emission
Radiated Emission
Radiated Emission
Conducted Disturbance
Conducted Power
Spurious RF Conducted Emission
Band Edge Compliance of RF Emission
Occuiped Bandwidth
Range
30~1000MHz
1~18GHz
18-40GHz
0.15~30MHz
9KHz~18GHz
9KHz~40GHz
9KHz~40GHz
9KHz~40GHz
Measurement
Uncertainty
3.10 dB
3.70 dB
3.90 dB
1.63 dB
0.61 dB
1.22 dB
1.22 dB
Notes
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1) This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level
using a coverage factor of k=1.96.
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QRP-AZUMIAKARU55Q Report No.: LCS170329088AE
4 TEST CONDITIONS AND RESULTS
4.1
Output Power
TEST APPLICABLE
During the process of testing, the EUT was controlled via R&S Digital Radio Communication tester (CMU200)
to ensure max power transmission and proper modulation. This result contains output power and EIRP
measurements for the EUT. In all cases, output power is within the specified limits.
4.1.1. Conducted Output Power
TEST CONFIGURATION
TEST PROCEDURE
Conducted Power Measurement:
a) Place the EUT on a bench and set it in transmitting mode.
b) Connect a low loss RF cable from the antenna port to a CMU200 by an Att.
c) EUT Communicate with CMU200 then selects a channel for testing.
d) Add a correction factor to the display CMU200, and then test.
TEST RESULTS
band
Item
sub-test
RMC
HSDPA
HSUPA
12.2kbps RMC
Sub –Test 1
Sub –Test 2
Sub –Test 3
Sub –Test 4
Sub –Test 1
Sub –Test 2
Sub –Test 3
Sub –Test 4
Sub –Test 5
WCDMA Band II result (dBm)
Channel/Frequency(MHz)
9262/
9400/
9538/
1852.4
1880
1907.6
23.57
23.68
23.45
23.61
23.56
22.34
22.55
22.15
21.73
21.50
21.67
21.64
21.23
21.39
22.46
22.65
21.17
21.80
21.68
21.37
21.45
21.65
21.59
20.76
20.79
20.50
21.35
21.24
20.79
23.45
WCDMA Band V result (dBm)
Channel/Frequency(MHz)
4132/
4183/
4233/
826.4
836.6
846.6
23.36
23.52
23.63
23.25
23.60
23.42
22.64
22.15
22.50
21.97
21.84
21.68
21.03
21.05
20.88
22.62
22.83
22.56
21.60
21.95
21.81
22.68
22.62
22.23
20.71
20.44
20.82
19.93
20.25
20.19
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QRP-AZUMIAKARU55Q Report No.: LCS170329088AE
4.1.1 Radiated Output Power
TEST DESCRIPTION
This is the test for the maximum radiated power from the EUT.
Rule Part 24.232(c) specifies, "Mobile/portable stations are limited to 2 watts e.i.r.p. Peak power" and
24.232(e) specifies that "Peak transmit power must be measured over any interval of continuous transmission
using instrumentation calibrated in terms of an rms-equivalent voltage."
Rule Part 22.913(a) specifies ” The ERP of mobile transmitters and auxiliary test transmitters must not exceed
7 Watts.”
TEST CONFIGURATION
TEST PROCEDURE
1. EUT was placed on a 1.50 meter high non-conductive stand at a 3 meter test distance from the receive
antenna. A receiving antenna was placed on the antenna mast 3 meters from the EUT for emission
measurements. The height of receiving antenna is 1.50m. Detected emissions were maximized at each
frequency by rotating the EUT through 360°and adjusting the receiving antenna polarization. The radiated
emission measurements of all transmit frequencies in three channels (High, Middle, Low) were measured
with peak detector.
2. A log-periodic antenna or double-ridged waveguide horn antenna shall be substituted in place of the EUT.
The log-periodic antenna will be driven by a signal generator and the level will be adjusted till the same
power value on the spectrum analyzer or receiver. The level of the spurious emissions can be calculated
through the level of the signal generator, cable loss, the gain of the substitution antenna and the reading
of the spectrum analyzer or receiver.
3. The EUT is then put into continuously transmitting mode at its maximum power level during the test.Set
Test Receiver or Spectrum RBW=10MHz,VBW=10MHz, And the maximum value of the receiver should
be recorded as (Pr).
4. The EUT shall be replaced by a substitution antenna. In the chamber, an substitution antenna for the
frequency band of interest is placed at the reference point of the chamber. An RF Signal source for the
frequency band of interest is connected to the substitution antenna with a cable that has been constructed
to not interfere with the radiation pattern of the antenna. A power (PMea) is applied to the input of the
substitution antenna, and adjust the level of the signal generator output until the value of the receiver
reach the previously recorded (Pr). The power of signal source (PMea) is recorded. The test should be
performed by rotating the test item and adjusting the receiving antenna polarization.
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QRP-AZUMIAKARU55Q Report No.: LCS170329088AE
5. A amplifier should be connected to the Signal Source output port. And the cable should be connect
between the Amplifier and the Substitution Antenna. The cable loss (Pcl) ,the Substitution Antenna Gain
(Ga) and the Amplifier Gain (PAg) should be recorded after test.
The measurement results are obtained as described below:
Power(EIRP)=PMea+ PAg - Pcl + Ga
6. This value is EIRP since the measurement is calibrated using an antenna of known gain (2.15 dBi) and
known input power.
7. ERP can be calculated from EIRP by subtracting the gain of the dipole, ERP = EIRP-2.15dBi.
TEST LIMIT
According to 22.913(a), 24.232(c), the ERP(EIRP) should be not exceeding following table limits:
UMTS Band II
Burst Average EIRP
FCC: ≤38.45dBm (7W)
UMTS Band V
Burst Average ERP
38.45dBm (7W)
TEST RESULTS
Remark:
1. We were tested all Configuration refer 3GPP TS134 121.
2. EIRP=PMea(dBm)-Pcl(dB)+PAg(dB)+Ga(dBi)
3. ERP = EIRP – 2.15dBi as EIRP by subtracting the gain of the dipole.
4. Margin = Emission Level - Limit
5. We test the H direction and V direction recorded worst case.
UMTS/TM1/UMTS Band II
Frequency
(MHz)
PMea
(dBm)
Pcl
(dB)
1852.40
1880.00
1907.60
-14.57
-15.09
-16.03
4.03
4.08
4.14
Ga
Antenna
Gain
(dB)
8.38
8.33
8.26
Burst
Average
EIRP
(dBm)
25.29
24.72
23.72
PAg
(dB)
35.51
35.56
35.63
Limit
(dBm)
Margin
(dB)
Polarization
33.01
33.01
33.01
-7.71
-8.28
-9.28
UMTS/TM1/UMTS Band V
Frequency
(MHz)
PMea
(dBm)
Pcl
(dB)
826.40
836.60
844.60
-12.83
-14.10
-14.05
3.45
3.49
3.55
Ga
Antenna
Gain
(dB)
8.45
8.45
8.36
Correction
(dB)
PAg
(dB)
2.15
2.15
2.15
33.79
33.85
33.88
Burst
Average
ERP
(dBm)
23.81
22.56
22.49
Limit
(dBm)
Margin
(dB)
Polarization
38.45
38.45
38.45
-14.64
-15.89
-15.96
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QRP-AZUMIAKARU55Q Report No.: LCS170329088AE
4.2
Radiated Spurious Emssion
TEST APPLICABLE
According to the TIA/EIA 603D:2010 and FCC Part 2.1033 test method, The Receiver or Spectrum was
th
scanned from lowest frequency frequency generated within the equipment to the 10 harmonic of the highest
frequency generated within the equipment, which is the transmitted carrier that can be as high as 1910 MHz.
The resolution bandwidth is set as outlined in Part 24.238, Part 22.917, RSS-132 §5.5 and RSS-133 §6.5. The
spectrum is scanned with the mobile station transmitting at carrier frequencies that pertain to low, mid and high
channels of WCDMA Band II and WCDMA Band V.
TEST CONFIGURATION
TEST PROCEDURE
1. EUT was placed on a 1.50 meter high non-conductive stand at a 3 meter test distance from the receive
antenna. A receiving antenna was placed on the antenna mast 3 meters from the EUT for emission
measurements. The height of receiving antenna is 1.50 m. Detected emissions were maximized at each
frequency by rotating the EUT through 360°and adjusting the receiving antenna polarization. The radiated
emission measurements of all transmit frequencies in three channels (High, Middle, Low) were measured
with peak detector.
2. A log-periodic antenna or double-ridged waveguide horn antenna shall be substituted in place of the EUT.
The log-periodic antenna will be driven by a signal generator and the level will be adjusted till the same
power value on the spectrum analyzer or receiver. The level of the spurious emissions can be calculated
through the level of the signal generator, cable loss, the gain of the substitution antenna and the reading
of the spectrum analyzer or receiver.
3. The EUT is then put into continuously transmitting mode at its maximum power level during the test.Set
Test Receiver or Spectrum RBW=1MHz,VBW=3MHz, And the maximum value of the receiver should be
recorded as (Pr).
4. The EUT shall be replaced by a substitution antenna. In the chamber, an substitution antenna for the
frequency band of interest is placed at the reference point of the chamber. An RF Signal source for the
frequency band of interest is connected to the substitution antenna with a cable that has been constructed
to not interfere with the radiation pattern of the antenna. A power (PMea) is applied to the input of the
substitution antenna, and adjust the level of the signal generator output until the value of the receiver
reach the previously recorded (Pr). The power of signal source (PMea) is recorded. The test should be
performed by rotating the test item and adjusting the receiving antenna polarization.
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QRP-AZUMIAKARU55Q Report No.: LCS170329088AE
5. A amplifier should be connected to the Signal Source output port. And the cable should be connect
between the Amplifier and the Substitution Antenna. The cable loss (Pcl) ,the Substitution Antenna Gain
(Ga) and the Amplifier Gain (PAg) should be recorded after test.
The measurement results are obtained as described below:
Power(EIRP)=PMea+ PAg - Pcl + Ga
6. This value is EIRP since the measurement is calibrated using an antenna of known gain (2.15 dBi) and
known input power.
7. ERP can be calculated from EIRP by subtracting the gain of the dipole, ERP = EIRP -2.15dBi.
8. In order to make sure test results more clearly,we set frequency range and sweep time for difference
frequency range as follows table:
Working
Frequency
UMTS/TM1/
WCDMA Band V
UMTS/TM1/
WCDMA Band II
Subrange
(GHz)
0.00009~0.15
0.00015~0.03
0.03~1
1~2
2~5
5~8
8~10
0.00009~0.15
0.00015~0.03
0.03~1
1~2
2~5
5~8
8~11
11~14
14~18
18~20
RBW
VBW
1KHz
10KHz
100KHz
1 MHz
1 MHz
1 MHz
1 MHz
1KHz
10KHz
100KHz
1 MHz
1 MHz
1 MHz
1 MHz
1 MHz
1 MHz
1 MHz
3KHz
30KHz
300KHz
3 MHz
3 MHz
3 MHz
3 MHz
3KHz
30KHz
300KHz
3 MHz
3 MHz
3 MHz
3 MHz
3 MHz
3 MHz
3 MHz
Sweep time
(s)
30
10
10
30
10
10
TEST LIMITS
According to 24.238, 22.917 and 27.54 specify that the power of any emission outside of the authorized
operating frequency ranges must be attenuated below the transmitting power (P) by a factor of at least 43 +
10 log(P) dB.
The specification that emissions shall be attenuated below the transmitter power (P) by at least 43 + 10 log
(P) dB, translates in the relevant power range (1 to 0.001 W) to -13 dBm. At 1 W the specified minimum
attenuation becomes 43 dB and relative to a 30 dBm (1 W) carrier becomes a limit of -13 dBm. At 0.001 W (0
dBm) the minimum attenuation is 13 dB, which again yields a limit of -13 dBm. In this way a translation of the
specification from relative to absolute terms is carried out.
Frequency
UMTS/TM1/ WCDMA
Band V
UMTS/TM1/ WCDMA
Band II
Channel
Low
Middle
High
Low
Middle
High
Frequency Range
9KHz-10GHz
9KHz -10GHz
9KHz -10GHz
9KHz -20GHz
9KHz -20GHz
9KHz -20GHz
Verdict
PASS
PASS
PASS
PASS
PASS
PASS
TEST RESULTS
Remark:
1. We were tested all Configuration refer 3GPP TS134 121.
2. EIRP=PMea(dBm)-Pcl(dB)+PAg(dB)+Ga(dBi)
3. ERP = EIRP – 2.15dBi as EIRP by subtracting the gain of the dipole.
4. Margin = EIRP - Limit
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QRP-AZUMIAKARU55Q Report No.: LCS170329088AE
UMTS/TM1/ WCDMA Band II _ Low Channel
Frequency
(MHz)
PMea
(dBm)
Pcl
(dB)
Diatance
3704.8
5557.2
3704.8
5557.2
-43.58
-48.13
-46.20
-50.20
5.26
6.11
5.26
6.11
3.00
3.00
3.00
3.00
Ga
Antenna
Gain(dB)
9.88
11.36
9.88
11.36
Peak
EIRP
(dBm)
-38.96
-42.88
-41.58
-44.95
Ga
Antenna
Gain(dB)
10.03
11.41
10.03
11.41
Peak
EIRP
(dBm)
-39.70
-43.72
-41.28
-45.34
Ga
Antenna
Gain(dB)
9.62
11.46
9.62
11.46
Peak
EIRP
(dBm)
-40.98
-43.24
-42.21
-45.53
Ga
Antenna
Gain(dB)
8.56
6.98
8.56
6.98
Peak
EIRP
(dBm)
-41.98
-44.31
-40.98
-45.82
Ga
Antenna
Gain(dB)
8.58
6.80
8.58
6.80
Peak
EIRP
(dBm)
-42.05
-44.24
-41.83
-46.85
Ga
Antenna
Gain(dB)
9.06
6.65
9.06
6.65
Peak
EIRP
(dBm)
-39.61
-43.16
-41.31
-45.95
Limit
(dBm)
Margin
(dB)
Polarization
-13.00
-13.00
-13.00
-13.00
-25.96
-29.88
-28.58
-31.95
Limit
(dBm)
Margin
(dB)
Polarization
-13.00
-13.00
-13.00
-13.00
-26.70
-30.72
-28.28
-32.34
Limit
(dBm)
Margin
(dB)
Polarization
-13.00
-13.00
-13.00
-13.00
-27.98
-30.24
-29.21
-32.53
Limit
(dBm)
Margin
(dB)
Polarization
-13.00
-13.00
-13.00
-13.00
-28.98
-31.31
-27.98
-32.82
Limit
(dBm)
Margin
(dB)
Polarization
-13.00
-13.00
-13.00
-13.00
-29.05
-31.24
-28.83
-33.85
Limit
(dBm)
Margin
(dB)
Polarization
-13.00
-13.00
-13.00
-13.00
-26.61
-30.16
-28.31
-32.95
UMTS/TM1/ WCDMA Band II _ Middle Channel
Frequency
(MHz)
PMea
(dBm)
Pcl
(dB)
Diatance
3760.0
5640.0
3760.0
5640.0
-44.41
-48.94
-45.99
-50.56
5.32
6.19
5.32
6.19
3.00
3.00
3.00
3.00
UMTS/TM1/ WCDMA Band II _ High Channel
Frequency
(MHz)
PMea
(dBm)
Pcl
(dB)
Diatance
3815.2
5722.8
3815.2
5722.8
-45.24
-48.46
-46.47
-50.75
5.36
6.24
5.36
6.24
3.00
3.00
3.00
3.00
UMTS/TM1/ WCDMA Band V _ Low Channel
Frequency
(MHz)
PMea
(dBm)
Pcl
(dB)
Diatance
1652.8
2479.2
1652.8
2479.2
-46.68
-47.00
-45.68
-48.51
3.86
4.29
3.86
4.29
3.00
3.00
3.00
3.00
UMTS/TM1/ WCDMA Band V _ Middle Channel
Frequency
(MHz)
PMea
(dBm)
Pcl
(dB)
Diatance
1672.8
2509.2
1672.8
2509.2
-46.73
-46.72
-46.51
-49.33
3.90
4.32
3.90
4.32
3.00
3.00
3.00
3.00
UMTS/TM1/ WCDMA Band V _ High Channel
Frequency
(MHz)
PMea
(dBm)
Pcl
(dB)
Diatance
1693.2
2539.8
1693.2
2539.8
-44.76
-45.49
-46.46
-48.28
3.91
4.32
3.91
4.32
3.00
3.00
3.00
3.00
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QRP-AZUMIAKARU55Q Report No.: LCS170329088AE
4.3
Occupied Bandwidth and Emission Bandwith
TEST APPLICABLE
Similar to conducted emissions; occupied bandwidth measurements are only provided for selected
frequencies in order to reduce the amount of submitted data. The table below lists the measured 99%
Bandwidth and -26dBc Bandwidth.
TEST CONFIGURATION
TEST PROCEDURE
1. The EUT was set up for the max output power with pseudo random data modulation;
2. The Occupied bandwidth and Emission Bandwidth were measured with Aglient Spectrum Analyzer
N9020A (peak);
3. Set RBW=100KHz,VBW=300KHz,Span=10MHz,SWT=Auto;
4. Set SPA Max hold and View, Set 99% Occupied Bandwidth/ Set -26dBc Occupied Bandwidth
5. These measurements were done at 3 frequencies for WCDMA band II/V. (low, middle and high of
operational frequency range).
TEST RESULTS
Test Mode
Channel
Frequency
(MHz)
UMTS/TM1/
WCDMA Band
UMTS/TM1/
WCDMA Band
II
4132
4183
4233
9262
9400
9538
826.40
836.60
846.60
1852.40
1880.00
1907.60
Occupied Bandwidth
(99% BW)
( MHz)
4.1043
4.1058
4.0906
4.1076
4.0909
4.1026
Emission Bandwidth
(-26 dBc BW)
( MHz)
4.682
4.653
4.682
4.693
4.681
4.666
Verdict
PASS
PASS
PASS
PASS
PASS
PASS
Remark:
1. Test results including cable loss;
2. Please refer to following plots;
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QRP-AZUMIAKARU55Q Report No.: LCS170329088AE
Occupied Bandwidth and Emission Bandwidth
UMTS/TM1/ WCDMA Band V
UMTS/TM1/ WCDMA Band II
Channel 4132 / 826.4 MHz
Channel 9262 / 1852.4 MHz
Channel 4183 / 836.6 MHz
Channel 9400 / 1880.0 MHz
Channel 4233 / 846.6 MHz
Channel 9538 / 1907.6 MHz
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QRP-AZUMIAKARU55Q Report No.: LCS170329088AE
4.4
Band Edge Compliance
TEST APPLICABLE
During the process of testing, the EUT was controlled via Digital Radio Communication tester (CMU200) to
ensure max power transmission and proper modulation.
TEST CONFIGURATION
TEST PROCEDURE
1. The EUT was set up for the max output power with pseudo random data modulation;
2. The power was measured with Spectrum Analyzer N9020A;
3. Set RBW=100KHz,VBW=300KHz,Span=10MHz,SWT=Auto,Dector: RMS;
These measurements were done at 2 frequencies for WCDMA Band II/V. (low and high of operational
frequency range).
TEST RESULTS
Test Mode
Channel
UMTS/TM1/WCDMA
Band V
4132
4233
Test Mode
Channel
UMTS/TM1/WCDMA
Band II
9262
9538
UMTS/TM1/WCDMA Band V
Frequency
Band Edg Compliance
(MHz)
(dBm)
826.40
<-13dBm
846.60
<-13dBm
UMTS/TM1/WCDMA Band II
Frequency
Band Edg Compliance
(MHz)
(dBm)
1852.40
<-13dBm
1907.60
<-13dBm
Limits
(dBm)
-13dBm
-13dBm
Limits
(dBm)
-13dBm
-13dBm
Verdict
PASS
Verdict
PASS
Remark:
1. Test results including cable loss;
2. Please refer to following plots;
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QRP-AZUMIAKARU55Q Report No.: LCS170329088AE
Band-edge Compliance
UMTS/TM1/WCDMA Band V
UMTS/TM1/WCDMA Band II
Channel 4132 / 826.4 MHz
Channel 9262 / 1852.4 MHz
Channel 4233 / 846.6 MHz
Channel 9538 / 1907.6 MHz
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QRP-AZUMIAKARU55Q Report No.: LCS170329088AE
4.5
Spurious Emssion on Antenna Port
TEST APPLICABLE
The following steps outline the procedure used to measure the conducted emissions from the EUT.
1. Determine frequency range for measurements: From CFR 2.1057 the spectrum should be investigated
from the lowest radio frequency generated in the equipment up to at least the 10th harmonic of the carrier
frequency. For the equipment of WCDMA band II, this equates to a frequency range of 9 KHz to 20GHz,
data taken from 30 MHz to 20 GHz. For WCDMA Band V, this equates to a frequency range of 9 KHz to 9
GHz,data taken from 30 MHz to 9 GHz.
2. The sweep time is set automatically by instrument itself. That should be the optimal sweep time for the
span and the RBW. If the sweep time is too short, that is sweep is too fast, the sweep result is not
accurate; if the sweep time is too long, that is sweep is too low, some frequency components may be lost.
The instrument will give an optimal sweep time according the selected span and RBW.
3. The procedure to get the conducted spurious emission is as follows:
The trace mode is set to MaxHold to get the highest signal at each frequency;
Wait 25 seconds;
Get the result.
4. Determine EUT transmit frequencies: below outlines the band edge frequencies pertinent to conducted
emissions testing.
TEST CONFIGURATION
TEST PROCEDURE
1. The EUT was set up for the max output power with pseudo random data modulation;
2. The power was measured with Spectrum Analyzer N9020A;
3. These measurements were done at 3 frequencies for WCDMA band II/V. (low, middle and high of
operational frequency range).
TEST LIMIT
Part 24.238, Part 22.917 specify that the power of any emission outside of the authorized operating frequency
ranges must be attenuated below the transmitting power (P) by a factor of at least 43 + 10 log(P) dB.
The specification that emissions shall be attenuated below the transmitter power (P) by at least 43 + 10 log
(P) dB, translates in the relevant power range (1 to 0.001 W) to -13 dBm. At 1 W the specified minimum
attenuation becomes 43 dB and relative to a 30 dBm (1 W) carrier becomes a limit of -13 dBm. At 0.001 W (0
dBm) the minimum attenuation is 13 dB, which again yields a limit of -13 dBm. In this way a translation of the
specification from relative to absolute terms is carried out.
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QRP-AZUMIAKARU55Q Report No.: LCS170329088AE
TEST RESULTS
Test Mode
UMTS/TM1/WCDMA
Band V
UMTS/TM1/WCDMA
Band II
Channel
Frequency
(MHz)
4132
4183
4233
9262
9400
9538
826.40
836.60
846.60
1852.40
1880.00
1907.60
Spurious RF
Conducted Emission
(dBm)
<-13dBm
<-13dBm
<-13dBm
<-13dBm
<-13dBm
<-13dBm
Limits
(dBm)
-13dBm
-13dBm
-13dBm
-13dBm
-13dBm
-13dBm
Verdict
PASS
PASS
Remark:
1. Test results including cable loss;
2. Please refer to following plots;
3. Not reorded test plots from 9 KHz to 30 MHz as emission levels 20dB lower than emission limit;
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QRP-AZUMIAKARU55Q Report No.: LCS170329088AE
Spurious Emssion on Antenna Port
UMTS/TM1/WCDMA Band V
Channel 4132 / 826.4 MHz
Channel 4183 / 836.6 MHz
30 MHz – 1000 MHz
30 MHz – 1000 MHz
1 GHz – 9 GHz
1 GHz – 9 GHz
UMTS/TM1/WCDMA Band V
Channel 4233 / 846.6 MHz
Channel 4233 / 846.6 MHz
30 MHz – 1000 MHz
1 GHz – 9 GHz
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QRP-AZUMIAKARU55Q Report No.: LCS170329088AE
Spurious Emssion on Antenna Port
UMTS/TM1/WCDMA Band II
Channel 9262 / 1852.4 MHz
Channel 9400 / 1880.0 MHz
30 MHz – 1000 MHz
30 MHz – 1000 MHz
1 GHz – 20 GHz
1 GHz – 20 GHz
UMTS/TM1/WCDMA Band II
Channel 9538 / 1907.6 MHz
Channel 9538 / 1907.6 MHz
30 MHz – 1000 MHz
1 GHz – 20 GHz
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QRP-AZUMIAKARU55Q Report No.: LCS170329088AE
4.6
Frequency Stability Test
TEST APPLICABLE
1.
2.
3.
According to FCC Part 2 Section 2.1055 (a)(1), the frequency stability shall be measured with variation of
ambient temperature from -30℃ to +50℃ centigrade.
According to FCC Part 2 Section 2.1055 (e)(2) and RSS-GEN, for battery powered equipment, the
frequency stability shall be measured with reducing primary supply voltage to the battery operating end
point, which is specified by the manufacture.
Vary primary supply voltage from 85 to 115 percent of the nominal value for other than hand carried
voltage equipment and the end voltage point was 3.40V.
TEST PROCEDURE
In order to measure the carrier frequency under the condition of AFC lock, it is necessary to make
measurements with the EUT in a “call mode”. This is accomplished with the use of R&S CMU200 DIGITAL
RADIO COMMUNICATION TESTER.
1. Measure the carrier frequency at room temperature;
2. Subject the EUT to overnight soak at -30℃;
3. With the EUT, powered via nominal voltage, connected to the CMU200 and in a simulated call on middle
channel of WCDMA Band II/V, measure the carrier frequency. These measurements should be made
within 2 minutes of Powering up the EUT, to prevent significant self-warming;
4. Repeat the above measurements at 10℃ increments from -30℃ to +50℃. Allow at least 0.5 hours at
each temperature, unpowered, before making measurements;
5. Remeasure carrier frequency at room temperature with nominal voltage. Vary supply voltage from
minimum voltage to maximum voltage, in 0.1Volt increments remeasuring carrier frequency at each
voltage. Pause at nominal voltage for 0.5 hours unpowered, to allow any self-heating to stabilize, before
continuing;
6. Subject the EUT to overnight soak at +50℃;
7. With the EUT, powered via nominal voltage, connected to the CMU200 and in a simulated call on the
centre channel, measure the carrier frequency. These measurements should be made within 2 minutes of
Powering up the EUT, to prevent significant self-warming;
8. Repeat the above measurements at 10℃ increments from +50℃ to -30℃. Allow at least 0.5 hours at
each temperature, unpowered, before making measurements;
9. At all temperature levels hold the temperature to +/- 0.5℃ during the measurement procedure;
TEST CONFIGURATION
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QRP-AZUMIAKARU55Q Report No.: LCS170329088AE
TEST LIMITS
For Hand carried battery powered equipment
According to the JTC standard the frequency stability of the carrier shall be accurate to within 0.1 ppm of the
received frequency from the base station. This accuracy is sufficient to meet Sec. 24.235, Frequency Stability.
The frequency stability shall be sufficient to ensure that the fundamental emission stays within the authorized
frequency block. As this transceiver is considered "Hand carried, battery powered equipment" Section
2.1055(d)(2) applies. This requires that the lower voltage for frequency stability testing be specified by the
manufacturer. This transceiver is specified to operate with an input voltage of between 3.40VDC and 4.20VDC,
with a nominal voltage of 3.70DC. Operation above or below these voltage limits is prohibited by transceiver
software in order to prevent improper operation as well as to protect components from overstress. These
voltages represent a tolerance of -10 % and +12.5 %. For the purposes of measuring frequency stability these
voltage limits are to be used.
For equipment powered by primary supply voltage
According to the JTC standard the frequency stability of the carrier shall be accurate to within 0.1 ppm of the
received frequency from the base station. This accuracy is sufficient to meet Sec. 24.235, Frequency Stability.
The frequency stability shall be sufficient to ensure that the fundamental emission stays within the authorized
frequency block. For this EUT section 2.1055(d)(1) applies. This requires varying primary supply voltage from
85 to 115 percent of the nominal value for other than hand carried battery equipment.
TEST RESULTS
DC Power
3.40
3.70
4.20
3.70
3.70
3.70
3.70
3.70
3.70
3.70
3.70
3.70
DC Power
3.40
3.70
4.20
3.70
3.70
3.70
3.70
3.70
3.70
3.70
3.70
3.70
Temperature
(℃)
25
25
25
-30
-20
-10
10
20
30
40
50
UMTS/TM1/WCDMA Band II
Frequency
Frequency
error(Hz)
error(ppm)
-5.65
-0.003
-9.93
-0.005
-9.77
-0.005
-5.61
-0.003
-5.74
-0.003
-4.26
-0.002
-2.57
-0.001
0.00
0.000
2.15
0.001
1.86
0.001
-8.57
-0.005
0.66
0.000
Limit
(ppm)
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
Temperature
(℃)
25
25
25
-30
-20
-10
10
20
30
40
50
UMTS/TM1/WCDMA Band V
Frequency
Frequency
error(Hz)
error(ppm)
-3.33
-0.004
-1.09
-0.001
-2.39
-0.003
0.10
0.000
-3.70
-0.004
0.88
0.001
5.70
0.007
5.64
0.007
3.35
0.004
2.16
0.003
3.73
0.004
-0.66
-0.001
Limit
(ppm)
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
2.50
Verdict
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
Verdict
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
PASS
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QRP-AZUMIAKARU55Q Report No.: LCS170329088AE
4.7
Peak-to-Average Ratio (PAR)
LIMIT
The Peak-to-Average Ratio (PAR) of the transmission may not exceed 13 dB.
TEST CONFIGURATION
TEST PROCEDURE
1. Refer to instrument’s analyzer instruction manual for details on how to use the power statistics/CCDF
function;
2. Set resolution/measurement bandwidth ≥ signal’s occupied bandwidth;
3. Set the number of counts to a value that stabilizes the measured CCDF curve;
4. Set the measurement interval as follows:
1). for continuous transmissions, set to 1 ms,
2). for burst transmissions, employ an external trigger that is synchronized with the EUT burst timing
sequence, or use the internal burst trigger with a trigger level that allows the burst to stabilize and set
the measurement interval to a time that is less than or equal to the burst duration.
5. Record the maximum PAPR level associated with a probability of 0.1%.
TEST RESULTS
Test Mode
Channel
UMTS/TM1/
WCDMA Band
II
UMTS/TM1/
WCDMA Band
9262
9400
9538
4132
4183
4233
Frequency
(MHz)
1852.40
1880.00
1907.60
826.40
836.60
846.60
PAPR Value
(dB)
2.09
2.10
2.10
2.10
2.09
2.10
Limits
(dB)
13.0
13.0
13.0
13.0
13.0
13.0
Verdict
PASS
PASS
PASS
PASS
PASS
PASS
Remark:
1. Test results including cable loss;
2. Please refer to following plots;
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QRP-AZUMIAKARU55Q Report No.: LCS170329088AE
Peak-to-Average Ratio (PAR)
UMTS/TM1/ WCDMA Band II
UMTS/TM1/ WCDMA Band V
Channel 9262 / 1852.4 MHz
Channel 4132/ 826.4 MHz
Channel 9400 / 1880.0 MHz
Channel 4183/ 836.6 MHz
Channel 9538 / 1907.6 MHz
Channel 4233/ 846.6 MHz
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: QRP-AZUMIAKARU55Q Report No.: LCS170329088AE
5 TEST SETUP PHOTOGRAPHS OF EUT
Please refer to separated files for Test Setup Photos of the EUT.
6 EXTERIOR PHOTOGRAPHS OF THE EUT
Please refer to separated files for External Photos of the EUT.
7 INTERIOR PHOTOGRAPHS OF THE EUT
Please refer to separated files for Internal Photos of the EUT.
.........................End of Report.........................
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Download: AZUMIAKARU55Q Mobile phone Test Report EMC TRF Template Azumi S.A
Mirror Download [FCC.gov]AZUMIAKARU55Q Mobile phone Test Report EMC TRF Template Azumi S.A
Document ID3422957
Application ID++QGuF9+6DJZHplGwzhBfg==
Document DescriptionTest report
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeTest Report
Display FormatAdobe Acrobat PDF - pdf
Filesize332.61kB (4157598 bits)
Date Submitted2017-06-12 00:00:00
Date Available2017-06-13 00:00:00
Creation Date2017-06-07 18:06:45
Producing SoftwareMicrosoft? Office Word 2007
Document Lastmod2017-06-07 18:06:45
Document TitleEMC TRF Template
Document CreatorMicrosoft? Office Word 2007
Document Author: eie

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 31
Language                        : zh-CN
Tagged PDF                      : Yes
Title                           :  EMC TRF Template
Author                          : eie
Creator                         : Microsoft? Office Word 2007
Create Date                     : 2017:06:07 18:06:45+08:00
Modify Date                     : 2017:06:07 18:06:45+08:00
Producer                        : Microsoft? Office Word 2007

Facebook Twitter Google+ RSS © FCCID.io 2017