FCC ID RYK-WNFQ291BEBT

CIIPC: Adding new antennas.

CIIPC for this application as described in this filling. CIIPC for this application. This changeestablishes portable category SAR conditions. The minimum test separation distance is5mm. The PIFA antenna Brand: HONGBO / Model: 260-25083 highest reported Body SAR,PD and Simultaneous SAR values are 0.74 W/kg, 5.01W/m2 and 1.58 W/kg, respectively.Single Modular Approval. Power listed is the EIRP. Co-transmission of this module withother transmitters requires a separate evaluation according to FCC multi-transmitterprocedures. The host integrator must follow the integration instructions provided by themodule manufacturer and ensure that the composite-system end product complies with theFCC requirements by a technical assessment or evaluation to the FCC rules and to KDBPublication 996369. The module antenna(s) must be installed to meet the RF exposurecompliance separation distance of 20 cm and any additional testing and authorizationprocess as required. The module grantee is responsible for providing the documentation tothe system integrator on restrictions of use, for continuing compliance of the module. Thehost integrator installing this module into their product must ensure that the final compositeproduct complies with the FCC requirements by a technical assessment or evaluation tothe FCC rules, including the transmitter operation and should refer to guidance in KDB996369. Approval is limited to OEM installation only. This grant is valid only when thedevice is sold to OEM integrators and the OEM integrators are instructed to ensure that theend user has no manual instructions to remove or install the device. Only those antenna(s)tested with the device or similar antenna(s) with equal or lesser gain may be used with thistransmitter. This device has 20 MHz, 40 MHz, 80 MHz, 160 MHz and 320 MHz bandwidthmodes. For 5.925-7.125GHz band operation, the PIFA antenna (Maximum 5.16 dBi gain)and Monopole antenna (Maximum 4.81 dBi gain) can be used with this approval. Devicemust compliant indoor restrictions when connected to indoor low power AP.

CIIPC: Adding new antennas.

CIIPC for this application. This change establishes portable category SAR conditions. Theminimum test separation distance is 5mm. The PIFA antenna Brand: HONGBO / Model:260-25094 highest reported Body and Simultaneous SAR values are 0.79 W/kg and 1.58W/kg, respectively. Single Modular Approval. U-NII-1 through U-NII-3 Power listed is themaximum combined conducted output power, U-NII-4 and U-NII -3 & -4 span channelsPower listed is the EIRP. Co-transmission of this module with other transmitters requires aseparate evaluation according to FCC multi-transmitter procedures. The host integratormust follow the integration instructions provided by the module manufacturer and ensurethat the composite-system end product complies with the FCC requirements by a technicalassessment or evaluation to the FCC rules and to KDB Publication 996369. The moduleantenna(s) must be installed to meet the RF exposure compliance separation distance of20 cm and any additional testing and authorization process as required. The modulegrantee is responsible for providing the documentation to the system integrator onrestrictions of use, for continuing compliance of the module. The host integrator installingthis module into their product must ensure that the final composite product complies withthe FCC requirements by a technical assessment or evaluation to the FCC rules, includingthe transmitter operation and should refer to guidance in KDB 996369. Approval is limitedto OEM installation only. This grant is valid only when the device is sold to OEM integratorsand the OEM integrators are instructed to ensure that the end user has no manualinstructions to remove or install the device. Only those antenna(s) tested with the device orsimilar antenna(s) with equal or lesser gain may be used with this transmitter. This devicehas 20 MHz, 40 MHz, 80 MHz and 160 MHz bandwidth modes.

CIIPC for this application. This change establishes portable category SAR conditions. Theminimum test separation distance is 5mm. The PIFA antenna Brand: HONGBO / Model:260-25094 highest reported Body and Simultaneous SAR values are 0.79 W/kg and 1.58W/kg, respectively. Single Modular Approval. U-NII-1 through U-NII-3 Power listed is themaximum combined conducted output power, U-NII-4 and U-NII -3 & -4 span channelsPower listed is the EIRP. Co-transmission of this module with other transmitters requires aseparate evaluation according to FCC multi-transmitter procedures. The host integratormust follow the integration instructions provided by the module manufacturer and ensurethat the composite-system end product complies with the FCC requirements by a technicalassessment or evaluation to the FCC rules and to KDB Publication 996369. The moduleantenna(s) must be installed to meet the RF exposure compliance separation distance of20 cm and any additional testing and authorization process as required. The modulegrantee is responsible for providing the documentation to the system integrator onrestrictions of use, for continuing compliance of the module. The host integrator installingthis module into their product must ensure that the final composite product complies withthe FCC requirements by a technical assessment or evaluation to the FCC rules, includingthe transmitter operation and should refer to guidance in KDB 996369. Approval is limitedto OEM installation only. This grant is valid only when the device is sold to OEM integratorsand the OEM integrators are instructed to ensure that the end user has no manualinstructions to remove or install the device. Only those antenna(s) tested with the device orsimilar antenna(s) with equal or lesser gain may be used with this transmitter. This devicehas 20 MHz, 40 MHz, 80 MHz and 160 MHz bandwidth modes.

CIIPC: Adding new antennas.

CIIPC for this application. Software change to enable QHS mode for this device. CIIPC forthis application. This change establishes portable category SAR conditions. The minimumtest separation distance is 5mm. The PIFA antenna Brand: HONGBO / Model: 260-25094highest reported Body and Simultaneous SAR values are 0.79 W/kg and 1.58 W/kg,respectively. Single Modular Approval. Power listed is the maximum conducted outputpower. Co-transmission of this module with other transmitters requires a separateevaluation according to FCC multi-transmitter procedures. The host integrator must followthe integration instructions provided by the module manufacturer and ensure that thecomposite-system end product complies with the FCC requirements by a technicalassessment or evaluation to the FCC rules and to KDB Publication 996369. The moduleantenna(s) must be installed to meet the RF exposure compliance separation distance of20 cm and any additional testing and authorization process as required. The modulegrantee is responsible for providing the documentation to the system integrator onrestrictions of use, for continuing compliance of the module. The host integrator installingthis module into their product must ensure that the final composite product complies withthe FCC requirements by a technical assessment or evaluation to the FCC rules, includingthe transmitter operation and should refer to guidance in KDB 996369. Approval is limitedto OEM installation only. This grant is valid only when the device is sold to OEM integratorsand the OEM integrators are instructed to ensure that the end user has no manualinstructions to remove or install the device. Only those antenna(s) tested with the device orsimilar antenna(s) with equal or lesser gain may be used with this transmitter.

CIIPC for this application. Software change to enable QHS mode for this device. CIIPC forthis application. This change establishes portable category SAR conditions. The minimumtest separation distance is 5mm. The PIFA antenna Brand: HONGBO / Model: 260-25094highest reported Body and Simultaneous SAR values are 0.79 W/kg and 1.58 W/kg,respectively. Single Modular Approval. Power listed is the maximum conducted outputpower. Co-transmission of this module with other transmitters requires a separateevaluation according to FCC multi-transmitter procedures. The host integrator must followthe integration instructions provided by the module manufacturer and ensure that thecomposite-system end product complies with the FCC requirements by a technicalassessment or evaluation to the FCC rules and to KDB Publication 996369. The moduleantenna(s) must be installed to meet the RF exposure compliance separation distance of20 cm and any additional testing and authorization process as required. The modulegrantee is responsible for providing the documentation to the system integrator onrestrictions of use, for continuing compliance of the module. The host integrator installingthis module into their product must ensure that the final composite product complies withthe FCC requirements by a technical assessment or evaluation to the FCC rules, includingthe transmitter operation and should refer to guidance in KDB 996369. Approval is limitedto OEM installation only. This grant is valid only when the device is sold to OEM integratorsand the OEM integrators are instructed to ensure that the end user has no manualinstructions to remove or install the device. Only those antenna(s) tested with the device orsimilar antenna(s) with equal or lesser gain may be used with this transmitter.

CIIPC for this application as described in this filling. CIIPC for this application. This changeestablishes portable category SAR conditions. The minimum test separation distance is5mm. The PIFA antenna Brand: HONGBO / Model: 260-25083 highest reported Body SAR,PD and Simultaneous SAR values are 0.74 W/kg, 5.01W/m2 and 1.58 W/kg, respectively.Single Modular Approval. Power listed is the EIRP. Co-transmission of this module withother transmitters requires a separate evaluation according to FCC multi-transmitterprocedures. The host integrator must follow the integration instructions provided by themodule manufacturer and ensure that the composite-system end product complies with theFCC requirements by a technical assessment or evaluation to the FCC rules and to KDBPublication 996369. The module antenna(s) must be installed to meet the RF exposurecompliance separation distance of 20 cm and any additional testing and authorizationprocess as required. The module grantee is responsible for providing the documentation tothe system integrator on restrictions of use, for continuing compliance of the module. Thehost integrator installing this module into their product must ensure that the final compositeproduct complies with the FCC requirements by a technical assessment or evaluation tothe FCC rules, including the transmitter operation and should refer to guidance in KDB996369. Approval is limited to OEM installation only. This grant is valid only when thedevice is sold to OEM integrators and the OEM integrators are instructed to ensure that theend user has no manual instructions to remove or install the device. Only those antenna(s)tested with the device or similar antenna(s) with equal or lesser gain may be used with thistransmitter. This device has 20 MHz, 40 MHz, 80 MHz, 160 MHz and 320 MHz bandwidthmodes. For 5.925-7.125GHz band operation, the PIFA antenna (Maximum 5.16 dBi gain)and Monopole antenna (Maximum 4.81 dBi gain) can be used with this approval. Devicemust compliant indoor restrictions when connected to indoor low power AP.

CIIPC for this application. This change establishes portable category SAR conditions. Theminimum test separation distance is 5mm. The PIFA antenna Brand: HONGBO / Model:260-25094 highest reported Body and Simultaneous SAR values are 0.74 W/kg and 1.58W/kg, respectively. Single Modular Approval. Power listed is the maximum combinedconducted output power. Co-transmission of this module with other transmitters requires aseparate evaluation according to FCC multi-transmitter procedures. The host integratormust follow the integration instructions provided by the module manufacturer and ensurethat the composite-system end product complies with the FCC requirements by a technicalassessment or evaluation to the FCC rules and to KDB Publication 996369. The moduleantenna(s) must be installed to meet the RF exposure compliance separation distance of20 cm and any additional testing and authorization process as required. The modulegrantee is responsible for providing the documentation to the system integrator onrestrictions of use, for continuing compliance of the module. The host integrator installingthis module into their product must ensure that the final composite product complies withthe FCC requirements by a technical assessment or evaluation to the FCC rules, includingthe transmitter operation and should refer to guidance in KDB 996369. Approval is limitedto OEM installation only. This grant is valid only when the device is sold to OEM integratorsand the OEM integrators are instructed to ensure that the end user has no manualinstructions to remove or install the device. Only those antenna(s) tested with the device orsimilar antenna(s) with equal or lesser gain may be used with this transmitter. This devicehas 20 MHz and 40 MHz bandwidth modes.

CIIPC: Adding new antennas.

CIIPC for this application. This change establishes portable category SAR conditions. Theminimum test separation distance is 5mm. The PIFA antenna Brand: HONGBO / Model:260-25094 highest reported Body and Simultaneous SAR values are 0.74 W/kg and 1.58W/kg, respectively. Single Modular Approval. Power listed is the maximum combinedconducted output power. Co-transmission of this module with other transmitters requires aseparate evaluation according to FCC multi-transmitter procedures. The host integratormust follow the integration instructions provided by the module manufacturer and ensurethat the composite-system end product complies with the FCC requirements by a technicalassessment or evaluation to the FCC rules and to KDB Publication 996369. The moduleantenna(s) must be installed to meet the RF exposure compliance separation distance of20 cm and any additional testing and authorization process as required. The modulegrantee is responsible for providing the documentation to the system integrator onrestrictions of use, for continuing compliance of the module. The host integrator installingthis module into their product must ensure that the final composite product complies withthe FCC requirements by a technical assessment or evaluation to the FCC rules, includingthe transmitter operation and should refer to guidance in KDB 996369. Approval is limitedto OEM installation only. This grant is valid only when the device is sold to OEM integratorsand the OEM integrators are instructed to ensure that the end user has no manualinstructions to remove or install the device. Only those antenna(s) tested with the device orsimilar antenna(s) with equal or lesser gain may be used with this transmitter. This devicehas 20 MHz and 40 MHz bandwidth modes.