FCC ID S22-BTAUDIO

BTAUDIO

by KC Wirefree Corporation

Grantee Code: S22   Product Code: BTAUDIO
Latest application date: 2015-03-25

FCC ID Device Details

FCC IDS22-BTAUDIO
Mirrorsfcc.id | gov | fccid.ai
Grantee CodeS22
Product CodeBTAUDIO
Applicant BusinessKC Wirefree Corporation 🇺🇸
Related Domains kcwirefree.com
Equipment ClassBTAUDIO
Test FirmCentre of Testing service Co., Ltd

Operating Frequencies

Frequency RangeApplication PurposeFinal Action Date
2402-2480 MHzOriginal Equipment2015-03-25

Exhibits

DocumentTypeAvailableFile
User ManualUsers Manual2015-03-25PDF 1 MB
Int PhotosInternal Photos2015-03-25PDF 193.9 KB
Ext PhotosExternal Photos2015-03-25PDF 220.1 KB
LabelID Label/Location Info2015-03-25PDF 70.4 KB
Test setup PhotosTest Setup Photos2015-03-25PDF 113.9 KB
Test Report - DSSTest Report2015-03-25PDF 1 MB
AuthorizationCover Letter(s)2015-03-25PDF 51.7 KB
Confid RequestCover Letter(s)2015-03-25PDF 70.1 KB
MPERF Exposure Info2015-03-25PDF 46.6 KB
Block Diagram Metadata onlyBlock DiagramPDF 248.9 KB
Schema Metadata onlySchematicsPDF 278.9 KB
Ops Des Metadata onlyOperational DescriptionPDF 128.9 KB
Parts List Metadata onlyParts List/Tune Up InfoPDF 185.8 KB

Application Information

Application IDPonzNq1RjkxJxEC0LZcAdg==
Final Action Date2015-03-25
Application PurposeOriginal Equipment
Applicant FRN0012568655
ModelBTAUDIO
Frequency Range2402-2480 MHz
Equipment ClassDSS - Part 15 Spread Spectrum Transmitter
Device DescriptionBTAUDIO
Responsible PartyChris Simonelic, President, chris@kcwirefree.com , 602-386-2640
Technical ContactSusan Zhang, Centre of Testing Service CO., LTD, ctszjy@cts-lab.com , (86)2022138571
Test FirmVincent Yao, Centre of Testing service Co., Ltd, vincent.yao@cts-lab.com.cn , 86-20-22138530
TCB Emailcertification@micomlabs.com
TCB ScopeA4: UNII devices & low power transmitters using spread spectrum techniques
Short-Term ConfidentialityNo
Long-Term ConfidentialityYes
Grant DeferralNo
Modular EquipmentSingle Modular Approval
Composite DeviceNo
Composite PartNo
Cognitive RadioNo
Authorization WaiverNo
Authorization Waiver ApprovedNo
Section 5301 CertificationYes
Related OET Knowledge DataBase InquiryNo
Grant CommentsModular Approval. Power Output listed is conducted. The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter, except in accordance with accepted multi-transmitter product procedures. OEM integrators must be provided with antenna installation instructions. OEM integrators and end-users must be provided with transmitter operation conditions for satisfying RF exposure compliance. The OEM integrators are instructed to ensure that the end user has no manual instructions to remove or install the device.

Applications

Application IDDatePurpose
PonzNq1RjkxJxEC0LZcAdg==2015-03-25Original Equipment

Equipment Authorization

FrequencyOutputRulesGrant Notes
2402-2480 MHz0.056000015C20

Grants

TCB Grant - Application PonzNq1RjkxJxEC0LZcAdg==

TCB GRANT OF EQUIPMENT
AUTHORIZATION
TCB
Certification
Issued Under the Authority of the
Federal Communications Commission
By:

  MiCOM Labs
575 Boulder Court
Pleasanton, CA 94566
Date of Grant: 03/25/2015

Application Dated: 03/25/2015
KC Wirefree Corporation
2640 W Medtronic Way
Tempe, AZ 85281
 
Attention: Chris Simonelic , President

NOT TRANSFERABLE
EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below.
 
FCC IDENTIFIER:  S22-BTAUDIO
Name of Grantee:  KC Wirefree Corporation
Equipment Class: Part 15 Spread Spectrum Transmitter
Notes: BTAUDIO
Modular Type: Single Modular
Grant Notes  FCC Rule Parts Frequency
Range (MHZ)
Output
Watts
Frequency
Tolerance
Emission
Designator
20 15C 2402.0  -  2480.0 0.056  

Modular Approval. Power Output listed is conducted. The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter, except in accordance with accepted multi-transmitter product procedures. OEM integrators must be provided with antenna installation instructions. OEM integrators and end-users must be provided with transmitter operation conditions for satisfying RF exposure compliance. The OEM integrators are instructed to ensure that the end user has no manual instructions to remove or install the device.

20: All electrical and mechanical devices employed for spurious radiation suppression, including any modifications made during certification testing, must be incorporated in each unit marketed.

EAS Grant - Application PonzNq1RjkxJxEC0LZcAdg==

COPY FEDERAL COMMUNICATIONS
COMMISSION
WASHINGTON, D.C. 20554

GRANT OF EQUIPMENT
AUTHORIZATION
COPY
Certification

KC Wirefree Corporation
2640 W Medtronic Way
Tempe, AZ 85281
United States
  Date of Grant: 03/25/2015

Application Dated: 03/25/2015
 
Attention: Chris Simonelic , President

NOT TRANSFERABLE
EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below.
 
FCC IDENTIFIER:  S22-BTAUDIO
Name of Grantee:  KC Wirefree Corporation
Equipment Class: Part 15 Spread Spectrum Transmitter
Notes: BTAUDIO
Modular Type: Single Modular
Grant Notes  FCC Rule Parts Frequency
Range (MHZ)
Output
Watts
Frequency
Tolerance
Emission
Designator
20 15C 2402.0  -  2480.0 0.056  

Modular Approval. Power Output listed is conducted. The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter, except in accordance with accepted multi-transmitter product procedures. OEM integrators must be provided with antenna installation instructions. OEM integrators and end-users must be provided with transmitter operation conditions for satisfying RF exposure compliance. The OEM integrators are instructed to ensure that the end user has no manual instructions to remove or install the device.


20: All electrical and mechanical devices employed for spurious radiation suppression, including any modifications made during certification testing, must be incorporated in each unit marketed.

Mail To: