FCC ID SX3-BCR200BT

Bluetooth Biometric Contact Card Reader

by PRADOTEC CORPORATION SDH. BHD. (807780-P)

Grantee Code: SX3   Product Code: BCR200BT
Latest application date: 2015-02-11

FCC ID Device Details

FCC IDSX3-BCR200BT
Mirrorsfcc.id | gov | fccid.ai
Grantee CodeSX3
Product CodeBCR200BT
Applicant BusinessPRADOTEC CORPORATION SDH. BHD. (807780-P) 🇲🇾
Related Domains pradotec.com.my
Equipment ClassBluetooth Biometric Contact Card Reader
Test FirmShenzhen Anbotek Compliance Laboratory Limited

Operating Frequencies

Frequency RangeApplication PurposeFinal Action Date
2402-2480 MHzOriginal Equipment2015-02-11

Exhibits

DocumentTypeAvailableFile
ManualUsers Manual2015-02-11PDF 163.3 KB
IntInternal Photos2015-02-11PDF 3.6 MB
ExtExternal Photos2015-02-11PDF 281 KB
LabelID Label/Location Info2015-02-11PDF 8.8 KB
LocationID Label/Location Info2015-02-11PDF 45.3 KB
SetupTest Setup Photos2015-02-11PDF 109 KB
Part 1Test Report2015-02-11PDF 5.7 MB
Part 2Test Report2015-02-11PDF 5.5 MB
Part 3Test Report2015-02-11PDF 5.6 MB
Part 4Test Report2015-02-11PDF 5.5 MB
AuthorizationCover Letter(s)2015-02-11PDF 61.3 KB
ConfidCover Letter(s)2015-02-11PDF 59.5 KB
DofCCover Letter(s)2015-02-11PDF 133.6 KB
RFxRF Exposure Info2015-02-11PDF 150.7 KB

Application Information

Application IDRIQc2atbdePMynwHkNKQpg==
Final Action Date2015-02-11
Application PurposeOriginal Equipment
Applicant FRN0022634364
ModelBCR200BT
Frequency Range2402-2480 MHz
Equipment ClassDSS - Part 15 Spread Spectrum Transmitter
Device DescriptionBluetooth Biometric Contact Card Reader
Responsible PartyJerene Goh, Product Assurance Engineer, jerene.goh@pradotec.com.my , 014-2298810
Technical ContactMark Koop, Teleconformity, mark.koop@teleconformity.com , (31)848395876
Test FirmDaniel zhu, Shenzhen Anbotek Compliance Laboratory Limited, Daniel.zhu@anbotek.com , 86-755-26014771
TCB Emailcertification@micomlabs.com
TCB ScopeA4: UNII devices & low power transmitters using spread spectrum techniques
Short-Term ConfidentialityNo
Long-Term ConfidentialityYes
Grant DeferralNo
Modular EquipmentDoes not apply
Composite DeviceNo
Composite PartNo
Cognitive RadioNo
Authorization WaiverNo
Authorization Waiver ApprovedNo
Section 5301 CertificationYes
Related OET Knowledge DataBase InquiryNo
Grant CommentsPower Output listed is Conducted. The antenna used for this transmitter must be installed to provide a separation distance of at least 5mm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter within a device, except in accordance with accepted multi-transmitter product procedures. End-users and installers must be provided with installation instructions and transmitter operating conditions for satisfying RF exposure compliance.

Applications

Application IDDatePurpose
RIQc2atbdePMynwHkNKQpg==2015-02-11Original Equipment

Equipment Authorization

FrequencyOutputRulesGrant Notes
2402-2480 MHz0.001820015C20

Grants

TCB Grant - Application RIQc2atbdePMynwHkNKQpg==

TCB GRANT OF EQUIPMENT
AUTHORIZATION
TCB
Certification
Issued Under the Authority of the
Federal Communications Commission
By:

  MiCOM Labs
575 Boulder Court
Pleasanton, CA 94566
Date of Grant: 02/11/2015

Application Dated: 02/11/2015
PRADOTEC CORPORATION SDH. BHD. (807780-P)
IRIS Smart Technology Complex,
Technology Park Malaysia,
Bukit Jalil, Kuala Lumpur, 57000
Malaysia
 
Attention: Jerene Goh , Product Assurance Engineer

NOT TRANSFERABLE
EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below.
 
FCC IDENTIFIER:  SX3-BCR200BT
Name of Grantee:  PRADOTEC CORPORATION SDH. BHD. (807780-P)
Equipment Class: Part 15 Spread Spectrum Transmitter
Notes: Bluetooth Biometric Contact Card Reader
Grant Notes  FCC Rule Parts Frequency
Range (MHZ)
Output
Watts
Frequency
Tolerance
Emission
Designator
20 15C 2402.0  -  2480.0 0.00182  

Power Output listed is Conducted. The antenna used for this transmitter must be installed to provide a separation distance of at least 5mm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter within a device, except in accordance with accepted multi-transmitter product procedures. End-users and installers must be provided with installation instructions and transmitter operating conditions for satisfying RF exposure compliance.

20: All electrical and mechanical devices employed for spurious radiation suppression, including any modifications made during certification testing, must be incorporated in each unit marketed.

EAS Grant - Application RIQc2atbdePMynwHkNKQpg==

COPY FEDERAL COMMUNICATIONS
COMMISSION
WASHINGTON, D.C. 20554

GRANT OF EQUIPMENT
AUTHORIZATION
COPY
Certification

PRADOTEC CORPORATION SDH. BHD. (807780-P)
IRIS Smart Technology Complex, Technology Park Malaysia,
Bukit Jalil, Kuala Lumpur, 57000
Malaysia
  Date of Grant: 02/11/2015

Application Dated: 02/11/2015
 
Attention: Jerene Goh , Product Assurance Engineer

NOT TRANSFERABLE
EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below.
 
FCC IDENTIFIER:  SX3-BCR200BT
Name of Grantee:  PRADOTEC CORPORATION SDH. BHD. (807780-P)
Equipment Class: Part 15 Spread Spectrum Transmitter
Notes: Bluetooth Biometric Contact Card Reader
Modular Type: Does not apply
Grant Notes  FCC Rule Parts Frequency
Range (MHZ)
Output
Watts
Frequency
Tolerance
Emission
Designator
20 15C 2402.0  -  2480.0 0.00182  

Power Output listed is Conducted. The antenna used for this transmitter must be installed to provide a separation distance of at least 5mm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter within a device, except in accordance with accepted multi-transmitter product procedures. End-users and installers must be provided with installation instructions and transmitter operating conditions for satisfying RF exposure compliance.


20: All electrical and mechanical devices employed for spurious radiation suppression, including any modifications made during certification testing, must be incorporated in each unit marketed.

Mail To: