141703 Secured Wireless Access Point Test Report DTS BT LE Fortinet Inc.

Fortinet Inc. Secured Wireless Access Point

FCC ID Filing: TVE-141703
Purchase on Amazon: Secured Wireless Access Point

Trouble Viewing? See the or view the HTML Version or PDF in frame
Page 1 of 141703 Secured Wireless Access Point Test Report DTS BT LE Fortinet Inc.
Page 2 of 141703 Secured Wireless Access Point Test Report DTS BT LE Fortinet Inc.
Page 3 of 141703 Secured Wireless Access Point Test Report DTS BT LE Fortinet Inc.
Page 4 of 141703 Secured Wireless Access Point Test Report DTS BT LE Fortinet Inc.
Page 5 of 141703 Secured Wireless Access Point Test Report DTS BT LE Fortinet Inc.
Page 6 of 141703 Secured Wireless Access Point Test Report DTS BT LE Fortinet Inc.
Page 7 of 141703 Secured Wireless Access Point Test Report DTS BT LE Fortinet Inc.
Page 8 of 141703 Secured Wireless Access Point Test Report DTS BT LE Fortinet Inc.
Page 9 of 141703 Secured Wireless Access Point Test Report DTS BT LE Fortinet Inc.
Page 10 of 141703 Secured Wireless Access Point Test Report DTS BT LE Fortinet Inc.
Page 11 of 141703 Secured Wireless Access Point Test Report DTS BT LE Fortinet Inc.
Page 12 of 141703 Secured Wireless Access Point Test Report DTS BT LE Fortinet Inc.
Page 13 of 141703 Secured Wireless Access Point Test Report DTS BT LE Fortinet Inc.
Page 14 of 141703 Secured Wireless Access Point Test Report DTS BT LE Fortinet Inc.
Page 15 of 141703 Secured Wireless Access Point Test Report DTS BT LE Fortinet Inc.
Page 16 of 141703 Secured Wireless Access Point Test Report DTS BT LE Fortinet Inc.
Page 17 of 141703 Secured Wireless Access Point Test Report DTS BT LE Fortinet Inc.
Page 18 of 141703 Secured Wireless Access Point Test Report DTS BT LE Fortinet Inc.
Page 19 of 141703 Secured Wireless Access Point Test Report DTS BT LE Fortinet Inc.
Page 20 of 141703 Secured Wireless Access Point Test Report DTS BT LE Fortinet Inc.
Page 21 of 141703 Secured Wireless Access Point Test Report DTS BT LE Fortinet Inc.
Page 22 of 141703 Secured Wireless Access Point Test Report DTS BT LE Fortinet Inc.
Page 23 of 141703 Secured Wireless Access Point Test Report DTS BT LE Fortinet Inc.
Page 24 of 141703 Secured Wireless Access Point Test Report DTS BT LE Fortinet Inc.
Page 25 of 141703 Secured Wireless Access Point Test Report DTS BT LE Fortinet Inc.
Page 26 of 141703 Secured Wireless Access Point Test Report DTS BT LE Fortinet Inc.
Page 27 of 141703 Secured Wireless Access Point Test Report DTS BT LE Fortinet Inc.
Page 28 of 141703 Secured Wireless Access Point Test Report DTS BT LE Fortinet Inc.
Page 29 of 141703 Secured Wireless Access Point Test Report DTS BT LE Fortinet Inc.
Page 30 of 141703 Secured Wireless Access Point Test Report DTS BT LE Fortinet Inc.
Page 31 of 141703 Secured Wireless Access Point Test Report DTS BT LE Fortinet Inc.
Page 32 of 141703 Secured Wireless Access Point Test Report DTS BT LE Fortinet Inc.
Page 33 of 141703 Secured Wireless Access Point Test Report DTS BT LE Fortinet Inc.
Page 34 of 141703 Secured Wireless Access Point Test Report DTS BT LE Fortinet Inc.

FCC Test Report
Report No.: RF170505C01
FCC ID: TVE-141703
Test Model: FortiAP 222E
Series Model: FortiAP 222Exxxxxx, FAP-222Exxxxxx, FORTIAP-222Exxxxxx (where “x”
can be used as “A-Z” or “0-9” or “-“ or blank for software changes or
marketing purposes only)
Received Date: May 05, 2017
Test Date: May 26 ~ Jul. 10, 2017
Issued Date: Jul. 25, 2017
Applicant: Fortinet lnc.
Address: 899 Kifer Road Sunnyvale, CA 94086 USA
Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch
Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan,
R.O.C.
Test Location: No. 19, Hwa Ya 2nd Rd., Wen Hwa Vil., Kwei Shan Dist., Taoyuan City
33383, TAIWAN (R.O.C.)
This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted
only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this
report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product
unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you
provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided,
however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time
shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific
mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification.
This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies.
Report No.: RF170505C01
Page No. 1 / 34
Report Format Version: 6.1.1
Table of Contents
Release Control Record .................................................................................................................................. 4
Certificate of Conformity...................................................................................................................... 5
Summary of Test Results ..................................................................................................................... 6
2.1
2.2
Measurement Uncertainty ................................................................................................................... 6
Modification Record ............................................................................................................................ 6
General Information .............................................................................................................................. 7
3.1
3.2
3.2.1
3.3
3.3.1
3.4
3.5
General Description of EUT ................................................................................................................ 7
Description of Test Modes ................................................................................................................... 8
Test Mode Applicability and Tested Channel Detail............................................................................. 9
Description of Support Units .............................................................................................................. 11
Configuration of System under Test ................................................................................................... 11
Duty Cycle of Test Signal .................................................................................................................. 12
General Description of Applied Standards ........................................................................................ 12
Test Types and Results ...................................................................................................................... 13
4.1
4.1.1
4.1.2
4.1.3
4.1.4
4.1.5
4.1.6
4.1.7
4.2
4.2.1
4.2.2
4.2.3
4.2.4
4.2.5
4.2.6
4.2.7
4.3
4.3.1
4.3.2
4.3.3
4.3.4
4.3.5
4.3.6
4.3.7
4.4
4.4.1
4.4.2
4.4.3
4.4.4
4.4.5
4.4.6
4.4.7
4.5
4.5.1
4.5.2
4.5.3
4.5.4
4.5.5
4.5.6
Radiated Emission and Bandedge Measurement............................................................................. 13
Limits of Radiated Emission and Bandedge Measurement .............................................................. 13
Test Instruments ................................................................................................................................ 14
Test Procedures................................................................................................................................. 15
Deviation from Test Standard ............................................................................................................ 15
Test Set Up ........................................................................................................................................ 16
EUT Operating Conditions................................................................................................................. 17
Test Results ....................................................................................................................................... 18
Conducted Emission Measurement .................................................................................................. 22
Limits of Conducted Emission Measurement .................................................................................... 22
Test Instruments ................................................................................................................................ 22
Test Procedures................................................................................................................................. 22
Deviation from Test Standard ............................................................................................................ 23
Test Setup .......................................................................................................................................... 23
EUT Operating Conditions................................................................................................................. 23
Test Results ....................................................................................................................................... 24
6dB Bandwidth Measurement ........................................................................................................... 26
Limits of 6dB Bandwidth Measurement ............................................................................................. 26
Test Setup .......................................................................................................................................... 26
Test Instruments ................................................................................................................................ 26
Test Procedure .................................................................................................................................. 26
Deviation from Test Standard ............................................................................................................ 26
EUT Operating Conditions................................................................................................................. 26
Test Result ......................................................................................................................................... 27
Conducted Output Power Measurement........................................................................................... 28
Limits of Conducted Output Power Measurement ............................................................................ 28
Test Setup .......................................................................................................................................... 28
Test Instruments ................................................................................................................................ 28
Test Procedures................................................................................................................................. 28
Deviation from Test Standard ............................................................................................................ 28
EUT Operating Conditions................................................................................................................. 28
Test Results ....................................................................................................................................... 28
Power Spectral Density Measurement .............................................................................................. 29
Limits of Power Spectral Density Measurement ............................................................................... 29
Test Setup .......................................................................................................................................... 29
Test Instruments ................................................................................................................................ 29
Test Procedure .................................................................................................................................. 29
Deviation from Test Standard ............................................................................................................ 29
EUT Operating Condition .................................................................................................................. 29
Report No.: RF170505C01
Page No. 2 / 34
Report Format Version: 6.1.1
4.5.7
4.6
4.6.1
4.6.2
4.6.3
4.6.4
4.6.5
4.6.6
4.6.7
Test Results ....................................................................................................................................... 30
Conducted Out of Band Emission Measurement .............................................................................. 31
Limits of Conducted Out of Band Emission Measurement ............................................................... 31
Test Setup .......................................................................................................................................... 31
Test Instruments ................................................................................................................................ 31
Test Procedure .................................................................................................................................. 31
Deviation from Test Standard ............................................................................................................ 31
EUT Operating Condition .................................................................................................................. 31
Test Results ....................................................................................................................................... 32
Pictures of Test Arrangements .......................................................................................................... 33
Appendix – Information on the Testing Laboratories ................................................................................ 34
Report No.: RF170505C01
Page No. 3 / 34
Report Format Version: 6.1.1
Release Control Record
Issue No.
Description
Date Issued
RF170505C01
Original release.
Jul. 25, 2017
Report No.: RF170505C01
Page No. 4 / 34
Report Format Version: 6.1.1
1
Certificate of Conformity
Product: Secured Wireless Access Point
Brand: Fortinet lnc.
Test Model: FortiAP 222E
Series Model: FortiAP 222Exxxxxx, FAP-222Exxxxxx, FORTIAP-222Exxxxxx (where “x” can be
used as “A-Z” or “0-9” or “-“ or blank for software changes or marketing purposes
only)
Sample Status: Engineering sample
Applicant: Fortinet lnc.
Test Date: May 26 ~ Jul. 10, 2017
Standards: 47 CFR FCC Part 15, Subpart C (Section 15.247)
ANSI C63.10:2013
The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd.,
Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data
evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts
of the measurements of the sample’s EMC characteristics under the conditions specified in this report.
Prepared by :
, Date:
Jul. 25, 2017
, Date:
Jul. 25, 2017
Pettie Chen / Senior Specialist
Approved by :
Ken Liu / Senior Manager
Report No.: RF170505C01
Page No. 5 / 34
Report Format Version: 6.1.1
2
Summary of Test Results
47 CFR FCC Part 15, Subpart C (Section 15.247)
FCC
Clause
15.207
Result
Remarks
Meet the requirement of limit.
Minimum passing margin is -5.01dB at
0.47060MHz.
Meet the requirement of limit.
Minimum passing margin is -1.6dB at
4880.00MHz.
AC Power Conducted Emission
Pass
15.205 /
15.209 /
15.247(d)
Radiated Emissions and Band Edge
Measurement
Pass
15.247(d)
Antenna Port Emission
Pass
Meet the requirement of limit.
6dB bandwidth
Pass
Meet the requirement of limit.
15.247(b)
Conducted power
Pass
Meet the requirement of limit.
15.247(e)
Power Spectral Density
Pass
Meet the requirement of limit.
Antenna Requirement
Pass
Antenna connector is RP SMA plug not
a standard connector.
15.247(a)(2)
15.203
2.1
Test Item
Measurement Uncertainty
Where relevant, the following measurement uncertainty levels have been estimated for tests performed on
the EUT as specified in CISPR 16-4-2:
Measurement
Frequency
Conducted Emissions at mains ports
150kHz ~ 30MHz
30MHz ~ 200MHz
200MHz ~1000MHz
1GHz ~ 18GHz
18GHz ~ 40GHz
Radiated Emissions up to 1 GHz
Radiated Emissions above 1 GHz
2.2
Expanded Uncertainty
(k=2) (±)
2.94 dB
3.86 dB
3.87 dB
2.29 dB
2.29 dB
Modification Record
There were no modifications required for compliance.
Report No.: RF170505C01
Page No. 6 / 34
Report Format Version: 6.1.1
3
3.1
General Information
General Description of EUT
Product
Secured Wireless Access Point
Brand
Fortinet lnc.
Test Model
FortiAP 222E
Series Model
FortiAP 222Exxxxxx, FAP-222Exxxxxx, FORTIAP-222Exxxxxx (where “x” can
be used as “A-Z” or “0-9” or “-“ or blank for software changes or marketing
purposes only)
Model Difference
Refer to Note
Status of EUT
Engineering sample
Power Supply Rating
54Vdc (POE)
Modulation Type
GFSK
Transfer Rate
1Mbps
Operating Frequency
2402 ~ 2480MHz
Number of Channel
40
Channel Spacing
2MHz
Output Power
3.126mW
Antenna Type
Dipole antenna with 2dBi gain
Antenna Connector
RP SMA plug
Accessory Device
PoE, wall mount
Data Cable Supplied
1.8m non-shielded Grounding Cable without core
Note:
1. All models are listed as below. Model FortiAP 222E is the representative for final test.
Brand
Model
Difference
FortiAP 222Exxxxxx
where “x” can be used as “A-Z” or “0-9” or “-“ or blank
Fortinet lnc.
FAP-222Exxxxxx
for software changes or marketing purposes only
FORTIAP-222Exxxxxx
2. The EUT consumes power from the following PoE.
PoE
Brand
SENAO
Model
EPA5006GPR
Input Power
100-240Vac~0.8A, 50-60Hz
Output Power
54Vdc / 0.6A
Power Cord
0.5m non-shielded power cord without core
3. The above EUT information is declared by manufacturer and for more detailed features description, please
refer to the manufacturer's specifications or user's manual.
Report No.: RF170505C01
Page No. 7 / 34
Report Format Version: 6.1.1
3.2
Description of Test Modes
40 channels are provided to this EUT:
Channel
Freq. (MHz)
Channel
Freq. (MHz)
Channel
Freq. (MHz)
Channel
Freq. (MHz)
2402
2404
2406
2408
2410
2412
2414
2416
2418
2420
10
11
12
13
14
15
16
17
18
19
2422
2424
2426
2428
2430
2432
2434
2436
2438
2440
20
21
22
23
24
25
26
27
28
29
2442
2444
2446
2448
2450
2452
2454
2456
2458
2460
30
31
32
33
34
35
36
37
38
39
2462
2464
2466
2468
2470
2472
2474
2476
2478
2480
Report No.: RF170505C01
Page No. 8 / 34
Report Format Version: 6.1.1
3.2.1
Test Mode Applicability and Tested Channel Detail
EUT
CONFIGURE
MODE
RE1G
RE<1G
PLC
APCM
√
√
√
√
Where
APPLICABLE TO
DESCRIPTION
RE1G: Radiated Emission above 1GHz &
Bandedge Measurement
RE<1G: Radiated Emission below 1GHz
PLC: Power Line Conducted Emission
APCM: Antenna Port Conducted Measurement
Note:
1. The EUT had been pre-tested on the positioned of each 3 axis. The worst case was found when positioned on Z-plane.
Radiated Emission Test (Above 1GHz):
Pre-Scan has been conducted to determine the worst-case mode from all possible combinations
between available modulations, data rates and antenna ports (if EUT with antenna diversity
architecture).
Following channel(s) was (were) selected for the final test as listed below.
EUT
CONFIGUURE
AVAILABLE CHANNEL
TESTED CHANNEL
MODULATION TYPE
DATA RATE (Mbps)
0 to 39
0, 19, 39
GFSK
MODE
Radiated Emission Test (Below 1GHz):
Pre-Scan has been conducted to determine the worst-case mode from all possible combinations
between available modulations, data rates and antenna ports (if EUT with antenna diversity
architecture).
Following channel(s) was (were) selected for the final test as listed below.
EUT
CONFIGUURE
AVAILABLE CHANNEL
TESTED CHANNEL
MODULATION TYPE
DATA RATE (Mbps)
0 to 39
GFSK
MODE
Power Line Conducted Emission Test:
Pre-Scan has been conducted to determine the worst-case mode from all possible combinations
between available modulations, data rates and antenna ports (if EUT with antenna diversity
architecture).
Following channel(s) was (were) selected for the final test as listed below.
EUT
CONFIGUURE
AVAILABLE CHANNEL
TESTED CHANNEL
MODULATION TYPE
DATA RATE (Mbps)
0 to 39
GFSK
MODE
Report No.: RF170505C01
Page No. 9 / 34
Report Format Version: 6.1.1
Antenna Port Conducted Measurement:
This item includes all test value of each mode, but only includes spectrum plot of worst value of each
mode.
Pre-Scan has been conducted to determine the worst-case mode from all possible combinations
between available modulations, data rates and antenna ports (if EUT with antenna diversity
architecture).
Following channel(s) was (were) selected for the final test as listed below.
EUT
CONFIGUURE
AVAILABLE CHANNEL
TESTED CHANNEL
MODULATION TYPE
DATA RATE (Mbps)
0 to 39
0, 19, 39
GFSK
MODE
Test Condition:
APPLICABLE TO
ENVIRONMENTAL CONDITIONS
INPUT POWER (SYSTEM)
TESTED BY
RE1G
23deg. C, 66%RH
120Vac, 60Hz
Willy Cheng
RE<1G
25deg. C, 66%RH
120Vac, 60Hz
Jones Chang
PLC
25deg. C, 67%RH
120Vac, 60Hz
Jones Chang
APCM
25deg. C, 60%RH
120Vac, 60Hz
Frank Liu
Report No.: RF170505C01
Page No. 10 / 34
Report Format Version: 6.1.1
3.3
Description of Support Units
The EUT has been tested as an independent unit together with other necessary accessories or support units.
The following support units or accessories were used to form a representative test configuration during the
tests.
ID
Product
Brand
Model No.
Serial No.
A.
Notebook
DELL
E5410
1HC2XM1
FCC ID
Remarks
FCC DoC Approved -
Note:
1. All power cords of the above support units are non-shielded (1.8m).
2. Item A acted as a communication partner to transfer data.
ID
Descriptions
Qty.
Length (m)
Shielding
(Yes/No)
Cores (Qty.)
Remarks
1.
RJ45 cable
1.0
2.
RJ45 cable
10
3.3.1
Configuration of System under Test
EUT
RJ45
(1)
PoE (EUT)
(2)
Remote site
Notebook (A)
Report No.: RF170505C01
Page No. 11 / 34
Report Format Version: 6.1.1
3.4
Duty Cycle of Test Signal
Duty cycle = 100%
3.5
General Description of Applied Standards
The EUT is a RF Product. According to the specifications of the manufacturer, it must comply with the
requirements of the following standards:
FCC Part 15, Subpart C (15.247)
558074 D01 DTS Meas Guidance v04
ANSI C63.10-2013
All test items have been performed and recorded as per the above standards.
NOTE: The EUT is also considered as a kind of computer peripheral, because the connection to computer is
necessary for typical use. It has been verified to comply with the requirements of FCC Part 15,
Subpart B, Class B (DoC). The test report has been issued separately.
Report No.: RF170505C01
Page No. 12 / 34
Report Format Version: 6.1.1
4
Test Types and Results
4.1
Radiated Emission and Bandedge Measurement
4.1.1
Limits of Radiated Emission and Bandedge Measurement
Radiated emissions which fall in the restricted bands must comply with the radiated emission limits specified
as below table. Other emissions shall be at least 30dB below the highest level of the desired power:
Frequencies
(MHz)
Field Strength
(microvolts/meter)
Measurement Distance
(meters)
0.009 ~ 0.490
2400/F(kHz)
300
0.490 ~ 1.705
24000/F(kHz)
30
1.705 ~ 30.0
30
30
30 ~ 88
100
88 ~ 216
150
216 ~ 960
200
Above 960
500
Note:
1.
The lower limit shall apply at the transition frequencies.
2.
Emission level (dBuV/m) = 20 log Emission level (uV/m).
3.
For frequencies above 1000MHz, the field strength limits are based on average detector, however, the
peak field strength of any emission shall not exceed the maximum permitted average limits, specified
above by more than 30dB under any condition of modulation.
Report No.: RF170505C01
Page No. 13 / 34
Report Format Version: 6.1.1
4.1.2
Test Instruments
Description &
Manufacturer
Test Receiver
ROHDE & SCHWARZ
Spectrum Analyzer
ROHDE & SCHWARZ
BILOG Antenna
SCHWARZBECK
HORN Antenna
SCHWARZBECK
HORN Antenna
SCHWARZBECK
Loop Antenna
Preamplifier
Agilent
Preamplifier
Agilent
RF signal cable
HUBER+SUHNER
RF signal cable
HUBER+SUHNER
Software
BV ADT
Antenna Tower
inn-co GmbH
Antenna Tower Controller
BV ADT
Turn Table
BV ADT
Turn Table Controller
BV ADT
High Speed Peak Power
Meter
Power Sensor
Model No.
Serial No.
Cal. Date
Cal. Due
ESIB7
100187
May 02, 2017
May 01, 2018
FSP40
100041
Nov. 16, 2016 Nov. 15, 2017
VULB9168
9168-171
Dec. 28, 2016 Dec. 27, 2017
9120D
209
Dec. 27, 2016 Dec. 26, 2017
BBHA 9170
BBHA9170241
Dec. 14, 2016 Dec. 13, 2017
EM-6879
269
Aug. 11, 2016 Aug. 10, 2017
8447D
2944A10738
Aug. 22, 2016 Aug. 21, 2017
8449B
3008A01922
Sep. 18, 2016 Sep. 17, 2017
SUCOFLEX 104
Cable-CH3-03 (214378) Aug. 22, 2016 Aug. 21, 2017
SUCOFLEX 106
Cable-CH3-03
(309224+12738)
ADT_Radiated_
V7.6.15.9.4
NA
NA
NA
MA 4000
013303
NA
NA
AT100
AT93021702
NA
NA
TT100
TT93021702
NA
NA
SC100
SC93021702
NA
NA
ML2495A
0824012
Aug. 11, 2016 Aug. 10, 2017
MA2411B
0738171
Aug. 11, 2016 Aug. 10, 2017
Aug. 22, 2016 Aug. 21, 2017
Note: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable
to NML/ROC and NIST/USA.
2. The test was performed in HwaYa Chamber 3.
3. The horn antenna and preamplifier (model: 8449B) are used only for the measurement of emission
frequency above 1GHz if tested.
4. The FCC Designation Number is TW0003. The number will be varied with the Lab location and
scope as attached.
5. The IC Site Registration No. is IC 7450F-3.
Report No.: RF170505C01
Page No. 14 / 34
Report Format Version: 6.1.1
4.1.3
Test Procedures
For Radiated emission below 30MHz
a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter chamber
room. The table was rotated 360 degrees to determine the position of the highest radiation.
b.
The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top
of a variable-height antenna tower.
c.
Both X and Y axes of the antenna are set to make the measurement.
d.
For each suspected emission, the EUT was arranged to its worst case and the rotatable table was turned
from 0 degrees to 360 degrees to find the maximum reading.
e.
The test-receiver system was set to Quasi-Peak Detect Function and Specified Bandwidth with
Maximum Hold Mode.
NOTE:
1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 9kHz at frequency
below 30MHz.
For Radiated emission above 30MHz
a. The EUT was placed on the top of a rotating table 0.8 meters (for 30MHz ~ 1GHz) / 1.5 meters (for above
1GHz) above the ground at 3 meter chamber room for test. The table was rotated 360 degrees to
determine the position of the highest radiation.
b.
The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top
of a variable-height antenna tower.
c.
The height of antenna is varied from one meter to four meters above the ground to determine the
maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to
make the measurement.
d.
For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned
to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to
find the maximum reading.
e.
The test-receiver system was set to quasi-peak detect function and specified bandwidth with maximum
hold mode when the test frequency is below 1 GHz.
f.
The test-receiver system was set to peak and average detect function and specified bandwidth with
maximum hold mode when the test frequency is above 1 GHz. If the peak reading value also meets
average limit, measurement with the average detector is unnecessary.
Note:
2. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120kHz for
Quasi-peak detection (QP) at frequency below 1GHz.
3.
The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and the video bandwidth is 3 MHz
for Peak detection (PK) at frequency above 1GHz.
4.
The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and the video bandwidth is ≥ 1/T
(Duty cycle < 98%) or 10 Hz (Duty cycle ≥ 98%) for Peak detection at frequency above 1GHz.
5.
All modes of operation were investigated and the worst-case emissions are reported.
4.1.4
Deviation from Test Standard
No deviation.
Report No.: RF170505C01
Page No. 15 / 34
Report Format Version: 6.1.1
4.1.5
Test Set Up
For Radiated emission below 30MHz
1m
EUT&
Support Units
3m
Turn Table
80cm
Ground Plane
Test Receiver
For Radiated emission 30MHz to 1GHz
Ant. Tower
EUT&
Support Units
3m
10m
1-4m
Variable
Turn Table
80cm
Ground Plane
Test Receiver
Report No.: RF170505C01
Page No. 16 / 34
Report Format Version: 6.1.1
For Radiated emission above 1GHz
Ant. Tower
EUT&
Support Units
3m
Turn Table
1-4m
Variable
Absorber
150cm
Ground Plane
Test Receiver
For the actual test configuration, please refer to the attached file (Test Setup Photo).
4.1.6
EUT Operating Conditions
a. Placed the EUT on the testing table.
b. Prepared a notebook to act as a communication partner and placed it outside of testing area.
c. The communication partner connected with EUT via a RJ45 cable and ran a test program (provided by
manufacturer) to enable EUT under transmission condition continuously at specific channel frequency.
d. The communication partner sent data to EUT by command "python".
e. The necessary accessories enable the system in full functions.
Report No.: RF170505C01
Page No. 17 / 34
Report Format Version: 6.1.1
4.1.7
Test Results
Above 1GHz Worst-Case Data
CHANNEL
TX Channel 0
FREQUENCY RANGE
1GHz ~ 25GHz
Peak (PK)
Average (AV)
DETECTOR
FUNCTION
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
NO.
FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
2390.00
2390.00
*2402.00
*2402.00
4804.00
4804.00
55.5 PK
43.4 AV
90.1 PK
88.7 AV
50.4 PK
41.3 AV
LIMIT
(dBuV/m)
MARGIN
(dB)
74.0
54.0
-18.5
-10.6
74.0
54.0
-23.6
-12.7
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
1.75 H
1.75 H
1.96 H
1.96 H
2.21 H
2.21 H
171
171
17
17
184
184
24.5
12.4
58.9
57.5
50.0
40.9
31.0
31.0
31.2
31.2
0.4
0.4
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
NO.
FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
2390.00
2390.00
*2402.00
*2402.00
4804.00
4804.00
55.2 PK
43.5 AV
101.3 PK
99.9 AV
57.3 PK
51.3 AV
LIMIT
(dBuV/m)
MARGIN
(dB)
74.0
54.0
-18.8
-10.5
74.0
54.0
-16.7
-2.7
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
1.13 V
1.13 V
1.68 V
1.68 V
1.11 V
1.11 V
18
18
11
11
24.2
12.5
70.1
68.7
56.9
50.9
31.0
31.0
31.2
31.2
0.4
0.4
Remarks:
1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m)
2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB)
3. The other emission levels were very low against the limit.
4. Margin value = Emission Level – Limit value
5. " * ": Fundamental frequency.
Report No.: RF170505C01
Page No. 18 / 34
Report Format Version: 6.1.1
CHANNEL
TX Channel 19
FREQUENCY RANGE
1GHz ~ 25GHz
Peak (PK)
Average (AV)
DETECTOR
FUNCTION
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
NO.
FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
*2440.00
*2440.00
4880.00
4880.00
90.0 PK
88.6 AV
51.0 PK
41.2 AV
LIMIT
(dBuV/m)
74.0
54.0
MARGIN
(dB)
-23.0
-12.8
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
1.17 H
1.17 H
2.07 H
2.07 H
194
194
181
181
58.7
57.3
50.4
40.6
31.3
31.3
0.6
0.6
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
NO.
FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
*2440.00
*2440.00
4880.00
4880.00
98.4 PK
96.9 AV
57.6 PK
52.4 AV
LIMIT
(dBuV/m)
74.0
54.0
MARGIN
(dB)
-16.4
-1.6
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
1.85 V
1.85 V
1.40 V
1.40 V
67.1
65.6
57.0
51.8
31.3
31.3
0.6
0.6
Remarks:
1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m)
2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB)
3. The other emission levels were very low against the limit.
4. Margin value = Emission Level – Limit value
5. " * ": Fundamental frequency.
Report No.: RF170505C01
Page No. 19 / 34
Report Format Version: 6.1.1
CHANNEL
TX Channel 39
FREQUENCY RANGE
1GHz ~ 25GHz
Peak (PK)
Average (AV)
DETECTOR
FUNCTION
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
NO.
FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
*2480.00
*2480.00
2483.50
2483.50
4960.00
4960.00
89.3 PK
87.9 AV
56.2 PK
43.6 AV
49.0 PK
37.7 AV
LIMIT
(dBuV/m)
74.0
54.0
74.0
54.0
MARGIN
(dB)
-17.8
-10.4
-25.0
-16.3
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
1.85 H
1.85 H
1.67 H
1.67 H
2.19 H
2.19 H
186
186
132
132
182
182
57.8
56.4
24.7
12.1
48.2
36.9
31.5
31.5
31.5
31.5
0.8
0.8
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
NO.
FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
*2480.00
*2480.00
2483.50
2483.50
4960.00
4960.00
100.9 PK
99.4 AV
57.1 PK
45.7 AV
54.1 PK
46.7 AV
LIMIT
(dBuV/m)
74.0
54.0
74.0
54.0
MARGIN
(dB)
-16.9
-8.3
-19.9
-7.3
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
1.37 V
1.37 V
1.31 V
1.31 V
1.28 V
1.28 V
171
171
163
163
359
359
69.4
67.9
25.6
14.2
53.3
45.9
31.5
31.5
31.5
31.5
0.8
0.8
Remarks:
1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m)
2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB)
3. The other emission levels were very low against the limit.
4. Margin value = Emission Level – Limit value
5. " * ": Fundamental frequency.
Report No.: RF170505C01
Page No. 20 / 34
Report Format Version: 6.1.1
Below 1GHz worst-case data
CHANNEL
TX Channel 19
FREQUENCY RANGE
30MHz ~ 1GHz
DETECTOR
FUNCTION
Quasi-Peak (QP)
ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
NO.
FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
LIMIT
(dBuV/m)
MARGIN
(dB)
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
57.12
96.01
140.72
169.89
210.72
811.50
28.8 QP
36.7 QP
31.7 QP
30.7 QP
32.9 QP
30.3 QP
40.0
43.5
43.5
43.5
43.5
46.0
-11.2
-6.8
-11.8
-12.8
-10.6
-15.7
2.00 H
2.00 H
2.00 H
1.51 H
1.51 H
1.51 H
44
306
98
81
188
16
43.4
55.8
46.0
44.6
49.0
31.6
-14.6
-19.1
-14.3
-13.9
-16.1
-1.3
ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
NO.
FREQ.
(MHz)
EMISSION
LEVEL
(dBuV/m)
LIMIT
(dBuV/m)
MARGIN
(dB)
ANTENNA
HEIGHT
(m)
TABLE
ANGLE
(Degree)
RAW
VALUE
(dBuV)
CORRECTION
FACTOR
(dB/m)
30.83
64.90
103.78
142.67
212.66
436.26
36.7 QP
34.9 QP
35.4 QP
27.9 QP
30.3 QP
23.9 QP
40.0
40.0
43.5
43.5
43.5
46.0
-3.3
-5.1
-8.1
-15.6
-13.2
-22.1
1.00 V
1.00 V
1.00 V
1.00 V
1.00 V
1.00 V
333
276
201
201
53.1
50.4
53.4
42.0
46.2
32.9
-16.4
-15.5
-18.0
-14.1
-15.9
-9.0
Remarks:
1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m)
2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB)
– Pre-Amplifier Factor(dB)
3. The other emission levels were very low against the limit of frequency range 30MHz ~ 1000MHz.
4. Margin value = Emission Level – Limit value
5. The emission levels were very low against the limit of frequency range 9kHz ~ 30MHz.
Report No.: RF170505C01
Page No. 21 / 34
Report Format Version: 6.1.1
4.2
Conducted Emission Measurement
4.2.1
Limits of Conducted Emission Measurement
Conducted Limit (dBuV)
Frequency (MHz)
Quasi-peak
Average
0.15 - 0.5
66 - 56
56 - 46
0.50 - 5.0
56
46
5.0 - 30.0
60
50
Note: 1. The lower limit shall apply at the transition frequencies.
2. The limit decreases in line with the logarithm of the frequency in the range of 0.15 to 0.50MHz.
4.2.2
Test Instruments
Description &
Manufacturer
Test Receiver
ROHDE & SCHWARZ
RF signal cable (with
10dB PAD)
Woken
LISN
ROHDE & SCHWARZ
(EUT)
LISN
ROHDE & SCHWARZ
(Peripheral)
Software
ADT
Model No.
Serial No.
Date Of Calibration
Due Date Of
Calibration
ESCI
100613
Nov. 21, 2016
Nov. 20, 2017
5D-FB
Cable-cond1-01
Dec. 22, 2016
Dec. 21, 2017
ESH3-Z5
835239/001
Mar. 10, 2017
Mar. 09, 2018
ESH3-Z5
100311
Jul. 28, 2016
Jul. 27, 2017
BV ADT_Cond_
V7.3.7.3
NA
NA
NA
Note: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable
to NML/ROC and NIST/USA.
2. The test was performed in HwaYa Shielded Room 1.
3. The VCCI Site Registration No. is C-2040.
4.2.3
Test Procedures
a.
The EUT was placed 0.4 meters from the conducting wall of the shielded room with EUT being
connected to the power mains through a line impedance stabilization network (LISN). Other support units
were connected to the power mains through another LISN. The two LISNs provide 50 ohm/ 50uH of
coupling impedance for the measuring instrument.
b.
Both lines of the power mains connected to the EUT were checked for maximum conducted interference.
c.
The frequency range from 150kHz to 30MHz was searched. Emission levels under (Limit - 20dB) was not
recorded.
Note: The resolution bandwidth and video bandwidth of test receiver is 9kHz for quasi-peak detection (QP)
and average detection (AV) at frequency 0.15MHz-30MHz.
Report No.: RF170505C01
Page No. 22 / 34
Report Format Version: 6.1.1
4.2.4
Deviation from Test Standard
No deviation.
4.2.5
Test Setup
Vertical Ground
Reference Plane
40cm
Test Receiver
EUT
80cm
LISN
Horizontal Ground
Reference Plane
Note: 1.Support units were connected to second LISN.
For the actual test configuration, please refer to the attached file (Test Setup Photo).
4.2.6
EUT Operating Conditions
Same as 4.1.6.
Report No.: RF170505C01
Page No. 23 / 34
Report Format Version: 6.1.1
4.2.7
Test Results
Phase
Line (L)
Channel
Channel 0
No
Freq.
Corr.
Factor
[MHz]
0.19418
0.47060
0.78600
1.96200
12.21400
20.79800
(dB)
10.43
10.50
10.48
10.52
11.01
11.46
Detector Function
Reading Value
[dB (uV)]
Q.P.
AV.
29.37
18.80
35.27
30.99
23.10
18.90
25.45
21.00
20.12
14.88
30.92
24.05
Emission Level
[dB (uV)]
Q.P.
AV.
39.80
29.23
45.77
41.49
33.58
29.38
35.97
31.52
31.13
25.89
42.38
35.51
Quasi-Peak (QP) /
Average (AV)
Limit
[dB (uV)]
Q.P.
AV.
63.86
53.86
56.50
46.50
56.00
46.00
56.00
46.00
60.00
50.00
60.00
50.00
Margin
(dB)
Q.P.
AV.
-24.06 -24.63
-10.73
-5.01
-22.42 -16.62
-20.03 -14.48
-28.87 -24.11
-17.62 -14.49
REMARKS:
1. Q.P. and AV. are abbreviations of quasi-peak and average individually.
2. The emission levels of other frequencies were very low against the limit.
3. Margin value = Emission level - Limit value
4. Correction factor = Insertion loss + Cable loss
5. Emission Level = Correction Factor + Reading Value.
Report No.: RF170505C01
Page No. 24 / 34
Report Format Version: 6.1.1
Phase
Neutral (N)
Channel
Channel 0
No
Freq.
Corr.
Factor
[MHz]
0.16105
0.19780
0.47400
0.74038
3.23800
20.55400
(dB)
10.16
10.20
10.23
10.24
10.38
11.07
Detector Function
Reading Value
[dB (uV)]
Q.P.
AV.
35.47
24.15
28.81
17.64
34.82
30.06
23.25
18.76
19.94
13.55
31.54
31.14
Emission Level
[dB (uV)]
Q.P.
AV.
45.63
34.31
39.01
27.84
45.05
40.29
33.49
29.00
30.32
23.93
42.61
42.21
Quasi-Peak (QP) /
Average (AV)
Limit
[dB (uV)]
Q.P.
AV.
65.41
55.41
63.70
53.70
56.44
46.44
56.00
46.00
56.00
46.00
60.00
50.00
Margin
(dB)
Q.P.
AV.
-19.78 -21.10
-24.69 -25.86
-11.39
-6.15
-22.51 -17.00
-25.68 -22.07
-17.39
-7.79
REMARKS:
1. Q.P. and AV. are abbreviations of quasi-peak and average individually.
2. The emission levels of other frequencies were very low against the limit.
3. Margin value = Emission level - Limit value
4. Correction factor = Insertion loss + Cable loss
5. Emission Level = Correction Factor + Reading Value.
Report No.: RF170505C01
Page No. 25 / 34
Report Format Version: 6.1.1
4.3
6dB Bandwidth Measurement
4.3.1
Limits of 6dB Bandwidth Measurement
The minimum of 6dB Bandwidth Measurement is 0.5 MHz.
4.3.2
Test Setup
EUT
4.3.3
Spectrum
Analyzer
Attenuator
Test Instruments
Refer to section 4.1.2 to get information of above instrument.
4.3.4
Test Procedure
a.
Set resolution bandwidth (RBW) = 100kHz
b.
Set the video bandwidth (VBW) ≥ 3 x RBW, Detector = Peak.
c.
Trace mode = max hold.
d.
Sweep = auto couple.
e.
Measure the maximum width of the emission that is constrained by the frequencies associated with the
two amplitude points (upper and lower) that are attenuated by 6 dB relative to the maximum level
measured in the fundamental emission
4.3.5
Deviation from Test Standard
No deviation.
4.3.6
EUT Operating Conditions
The software provided by client to enable the EUT under transmission condition continuously at lowest,
middle and highest channel frequencies individually.
Report No.: RF170505C01
Page No. 26 / 34
Report Format Version: 6.1.1
4.3.7
Test Result
Channel
Frequency (MHz)
6dB Bandwidth
(MHz)
Minimum Limit
(MHz)
Pass / Fail
2402
0.71
0.5
Pass
19
2440
0.72
0.5
Pass
39
2480
0.74
0.5
Pass
Spectrum Plot of Worst Value
Report No.: RF170505C01
Page No. 27 / 34
Report Format Version: 6.1.1
4.4
Conducted Output Power Measurement
4.4.1
Limits of Conducted Output Power Measurement
For systems using digital modulation in the 2400–2483.5 MHz bands: 1 Watt (30dBm)
4.4.2
Test Setup
EUT
4.4.3
Power Sensor
Attenuator
Power Meter
Test Instruments
Refer to section 4.1.2 to get information of above instrument.
4.4.4
Test Procedures
A peak / average power sensor was used on the output port of the EUT. A power meter was used to read the
response of the peak / average power sensor. Record the power level.
4.4.5
Deviation from Test Standard
No deviation.
4.4.6
EUT Operating Conditions
Same as Item 4.3.6.
4.4.7
Test Results
Channel
Frequency (MHz)
Average Power
(mW)
Average Power
(dBm)
Limit (dBm)
Pass/Fail
2402
3.126
4.95
30
Pass
19
2440
1.734
2.39
30
Pass
39
2480
2.891
4.61
30
Pass
Report No.: RF170505C01
Page No. 28 / 34
Report Format Version: 6.1.1
4.5
Power Spectral Density Measurement
4.5.1
Limits of Power Spectral Density Measurement
The Maximum of Power Spectral Density Measurement is 8dBm.
4.5.2
Test Setup
EUT
4.5.3
Attenuator
Spectrum
Analyzer
Test Instruments
Refer to section 4.1.2 to get information of above instrument.
4.5.4
Test Procedure
a.
Set analyzer center frequency to DTS channel center frequency.
b.
Set the span to 1.5 times the DTS bandwidth.
c.
Set the RBW to: 3 kHz ≤ RBW ≤ 100 kHz.
d.
Set the VBW ≥ 3 × RBW.
e.
Detector = peak.
f.
Sweep time = auto couple.
g.
Trace mode = max hold.
h.
Allow trace to fully stabilize.
i.
Use the peak marker function to determine the maximum amplitude level within the RBW.
4.5.5
Deviation from Test Standard
No deviation.
4.5.6
EUT Operating Condition
Same as Item 4.3.6
Report No.: RF170505C01
Page No. 29 / 34
Report Format Version: 6.1.1
4.5.7
Test Results
Channel
Freq.
(MHz)
PSD
(dBm)
Limit
(dBm)
Pass
/Fail
2402
-12.82
Pass
19
2440
-15.66
Pass
39
2480
-13.83
Pass
Spectrum Plot of Worst Value
Report No.: RF170505C01
Page No. 30 / 34
Report Format Version: 6.1.1
4.6
Conducted Out of Band Emission Measurement
4.6.1
Limits of Conducted Out of Band Emission Measurement
Below 30dB of the highest emission level of operating band (in 100kHz Resolution Bandwidth).
4.6.2
Test Setup
EUT
4.6.3
Attenuator
Spectrum
Analyzer
Test Instruments
Refer to section 4.1.2 to get information of above instrument.
4.6.4
Test Procedure
MEASUREMENT PROCEDURE REF
a.
b.
c.
d.
e.
f.
g.
Set the RBW = 100 kHz.
Set the VBW ≥ 300 kHz.
Detector = peak.
Sweep time = auto couple.
Trace mode = max hold.
Allow trace to fully stabilize.
Use the peak marker function to determine the maximum power level in any 100 kHz band segment
within the fundamental EBW.
MEASUREMENT PROCEDURE OOBE
a.
b.
c.
d.
e.
f.
g.
Set RBW = 100 kHz.
Set VBW ≥ 300 kHz.
Detector = peak.
Sweep = auto couple.
Trace Mode = max hold.
Allow trace to fully stabilize.
Use the peak marker function to determine the maximum amplitude level.
4.6.5
Deviation from Test Standard
No deviation.
4.6.6
EUT Operating Condition
Same as Item 4.3.6
Report No.: RF170505C01
Page No. 31 / 34
Report Format Version: 6.1.1
4.6.7
Test Results
CH 0
CH 19
CH 39
CH 0 Band edge
Report No.: RF170505C01
CH 39 Band edge
Page No. 32 / 34
Report Format Version: 6.1.1
5
Pictures of Test Arrangements
Please refer to the attached file (Test Setup Photo).
Report No.: RF170505C01
Page No. 33 / 34
Report Format Version: 6.1.1
Appendix – Information on the Testing Laboratories
We, Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, were founded in 1988 to
provide our best service in EMC, Radio, Telecom and Safety consultation. Our laboratories are FCC
recognized accredited test firms and accredited and approved according to ISO/IEC 17025.
If you have any comments, please feel free to contact us at the following:
Linko EMC/RF Lab
Tel: 886-2-26052180
Fax: 886-2-26051924
Hsin Chu EMC/RF/Telecom Lab
Tel: 886-3-6668565
Fax: 886-3-6668323
Hwa Ya EMC/RF/Safety Lab
Tel: 886-3-3183232
Fax: 886-3-3270892
Email: [email protected]
Web Site: www.bureauveritas-adt.com
The address and road map of all our labs can be found in our web site also.
--- END ---
Report No.: RF170505C01
Page No. 34 / 34
Report Format Version: 6.1.1
Download: 141703 Secured Wireless Access Point Test Report DTS BT LE Fortinet Inc.
Mirror Download [FCC.gov]141703 Secured Wireless Access Point Test Report DTS BT LE Fortinet Inc.
Document ID3541641
Application ID85t4ONxl847D67FGxP5jpA==
Document DescriptionTest Report DTS BT LE
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeTest Report
Display FormatAdobe Acrobat PDF - pdf
Filesize37.87kB (473434 bits)
Date Submitted2017-09-01 00:00:00
Date Available2017-09-06 00:00:00
Creation Date2017-08-31 09:09:32
Producing SoftwareAcrobat Distiller 11.0 (Windows)
Document Lastmod2017-08-31 09:09:49
Document TitleTest Report DTS BT LE
Document CreatorPScript5.dll Version 5.2.2
Document Author: pettchen

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : pettchen
Create Date                     : 2017:08:31 09:09:32+08:00
Modify Date                     : 2017:08:31 09:09:49+08:00
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2017:08:31 09:09:49+08:00
Producer                        : Acrobat Distiller 11.0 (Windows)
Format                          : application/pdf
Title                           : Microsoft Word - RF170505C01_Senao_FortiAP 222E__Secured Wireless Access Point__LE
Creator                         : pettchen
Document ID                     : uuid:5042fd1f-0665-4290-811b-9d6ef6d73121
Instance ID                     : uuid:c602ad77-06a0-4c30-9c53-f52dcd193447
Page Count                      : 34
EXIF Metadata provided by EXIF.tools

Facebook Twitter Google+ RSS © FCCID.io 2017