FCC ID UZ721121559
RFID Reader Module
by Zebra Technologies Corporation
Grantee Code: UZ7 Product Code: 21121559
Latest application date: 2014-11-06
FCC ID Device Details
Operating Frequencies
| Frequency Range | Application Purpose | Final Action Date |
|---|---|---|
| 902.6-927.4 MHz | Class II permissive change or modification of presently authorized equipment | 2014-11-06 |
| 902.6-927.4 MHz | Class II permissive change or modification of presently authorized equipment | 2009-12-08 |
| 902.6-927.4 MHz | Class II permissive change or modification of presently authorized equipment | 2009-12-02 |
| 902.75-927.25 MHz | Class II permissive change or modification of presently authorized equipment | 2009-07-28 |
| 902.75-927.25 MHz | Original Equipment | 2009-04-10 |
Exhibits
| Document | Type | Available | File |
|---|---|---|---|
| User Manual 1 | Users Manual | 2015-05-05 | PDF 1,024 KB |
| User Manual 2 | Users Manual | 2015-05-05 | PDF 971.8 KB |
| User Manual | Users Manual | 2009-12-08 | PDF 5 KB |
| Manual | Users Manual | 2009-04-10 | PDF 1.3 MB |
| Internal Photos 2 | Internal Photos | 2015-05-05 | PDF 816.8 KB |
| Internal Photos | Internal Photos | 2009-12-08 | PDF 396.9 KB |
| Internal Photos | Internal Photos | 2009-12-02 | PDF 277.4 KB |
| Internal Photos | Internal Photos | 2009-07-28 | PDF 383.8 KB |
| Internal Photos | Internal Photos | 2009-04-10 | PDF 141.7 KB |
| External Photos 1 | External Photos | 2015-05-05 | PDF 110.7 KB |
| External Photos 2 | External Photos | 2015-05-05 | PDF 358.7 KB |
| External Photos | External Photos | 2009-12-08 | PDF 171.3 KB |
| External Photos | External Photos | 2009-12-02 | PDF 190 KB |
| External Photos | External Photos | 2009-07-28 | PDF 181.1 KB |
| External Photos | External Photos | 2009-04-10 | PDF 108.4 KB |
| Label Info | ID Label/Location Info | 2014-11-06 | PDF 468.9 KB |
| Label | ID Label/Location Info | 2009-04-10 | PDF 96.9 KB |
| Label Location | ID Label/Location Info | 2009-04-10 | PDF 15.9 KB |
| Test Setup Photos | Test Setup Photos | 2015-05-05 | PDF 327.6 KB |
| Test Setup Photos SAR | Test Setup Photos | 2015-05-05 | PDF 368 KB |
| Test Setup Photos | Test Setup Photos | 2009-12-08 | PDF 181.1 KB |
| Test Setup Photos | Test Setup Photos | 2009-12-02 | PDF 256 KB |
| Test Setup Photos | Test Setup Photos | 2009-07-28 | PDF 319.7 KB |
| Test Setup Photos | Test Setup Photos | 2009-04-10 | PDF 324.4 KB |
| Test Report | Test Report | 2014-11-06 | PDF 494 KB |
| Test Report | Test Report | 2009-12-08 | PDF 1.1 MB |
| Test Report-1 | Test Report | 2009-12-02 | PDF 2.2 MB |
| Test Report-2 | Test Report | 2009-12-02 | PDF 2.1 MB |
| Test Report-3 | Test Report | 2009-12-02 | PDF 2.3 MB |
| Test Report | Test Report | 2009-07-28 | PDF 1.5 MB |
| Test Report Part 1 | Test Report | 2009-04-10 | PDF 2.6 MB |
| Test Report Part 2 | Test Report | 2009-04-10 | PDF 1.1 MB |
| Attestation Statement-Professional Installation | Attestation Statements | 2009-12-08 | PDF 19.7 KB |
| Attestation-Professional Installation | Attestation Statements | 2009-12-02 | PDF 19.7 KB |
| Attestation Chip Spec | Attestation Statements | 2009-07-28 | PDF 15.4 KB |
| Attestation Professional Inst | Attestation Statements | 2009-07-28 | PDF 19.7 KB |
| Attestation Professional Installation | Attestation Statements | 2009-04-10 | PDF 17.6 KB |
| Authorization Letter | Cover Letter(s) | 2014-11-06 | PDF 53.9 KB |
| Class II Change Letter | Cover Letter(s) | 2014-11-06 | PDF 14 KB |
| Confidential Letter Metadata only | Cover Letter(s) | 2014-11-06 | PDF 18.2 KB |
| Confidential Letter Rev | Cover Letter(s) | 2014-11-06 | PDF 48.8 KB |
| Short Term Confidential Letter | Cover Letter(s) | 2014-11-06 | PDF 18.4 KB |
| Cover Letter-Description of Change | Cover Letter(s) | 2009-12-08 | PDF 64.4 KB |
| CoverLetter-POA-1 | Cover Letter(s) | 2009-12-08 | PDF 491 KB |
| CoverLetter-POA-2 | Cover Letter(s) | 2009-12-08 | PDF 42.6 KB |
| Confidentiality Request | Cover Letter(s) | 2009-12-02 | PDF 40.7 KB |
| CoverLetter-Agent Auth | Cover Letter(s) | 2009-12-02 | PDF 42.6 KB |
| CoverLetter-Contact Auth | Cover Letter(s) | 2009-12-02 | PDF 491 KB |
| CoverLetter-Description of Change | Cover Letter(s) | 2009-12-02 | PDF 57.1 KB |
| Confidentiality Request | Cover Letter(s) | 2009-07-28 | PDF 41.8 KB |
| Cover Letter Desc of Change | Cover Letter(s) | 2009-07-28 | PDF 12.4 KB |
| CoverLetter Agent Auth | Cover Letter(s) | 2009-07-28 | PDF 55.3 KB |
| Coverletter Contact Auth 1 | Cover Letter(s) | 2009-07-28 | PDF 18.7 KB |
| Coverletter Contact Auth 2 | Cover Letter(s) | 2009-07-28 | PDF 491 KB |
| Confidentiality | Cover Letter(s) | 2009-04-10 | PDF 25.1 KB |
| CoverLetter POA 1 | Cover Letter(s) | 2009-04-10 | PDF 18.7 KB |
| CoverLetter POA 2 | Cover Letter(s) | 2009-04-10 | PDF 491 KB |
| CoverLetter POA 3 | Cover Letter(s) | 2009-04-10 | PDF 86.7 KB |
| Modular Approval Request | Cover Letter(s) | 2009-04-10 | PDF 27.5 KB |
| SAR Report | RF Exposure Info | 2014-11-06 | PDF 1.1 MB |
| SAR Report Appendix A | RF Exposure Info | 2014-11-06 | PDF 267.6 KB |
| SAR Report Appendix B | RF Exposure Info | 2014-11-06 | PDF 239.6 KB |
| SAR Report Appendix C | RF Exposure Info | 2014-11-06 | PDF 3 MB |
| RF Exposure Info | RF Exposure Info | 2009-12-08 | PDF 42.7 KB |
| RF Exposure Info | RF Exposure Info | 2009-12-02 | PDF 125 KB |
| RF Exposure Info | RF Exposure Info | 2009-07-28 | PDF 43.6 KB |
| RF Exposure | RF Exposure Info | 2009-04-10 | PDF 43.1 KB |
| Block Diagram Metadata only | Block Diagram | PDF 382.6 KB | |
| Schematics Metadata only | Schematics | PDF 57.5 KB | |
| Operational Description Metadata only | Operational Description | PDF 571.6 KB | |
| Parts List Metadata only | Parts List/Tune Up Info | PDF 160.1 KB |
Application Information
| Application ID | dIRw+LWCQzcLqMDJk7cOBw== |
|---|---|
| Final Action Date | 2014-11-06 |
| Application Purpose | Class II permissive change or modification of presently authorized equipment |
| Applicant FRN | 0015642663 |
| Model | 21121559 |
| Frequency Range | 902.6-927.4 MHz |
| Equipment Class | DSS - Part 15 Spread Spectrum Transmitter |
| Device Description | RFID Reader Module |
| Responsible Party | Qianlin Zhou, Regulatory Specialist, Larry.Zhou@zebra.com  , 346-260-3543 |
| Test Firm | Olivier HEYER, EMITECH Montpellier, o.heyer@emitech-group.com  , 33-4-67-871102 |
| TCB Email | TEI@TIMCOENGR.COM  |
| TCB Scope | A4: UNII devices & low power transmitters using spread spectrum techniques |
| Short-Term Confidentiality | Yes |
| Short-Term Confidentiality Date | 05/05/2015 |
| Long-Term Confidentiality | Yes |
| Grant Deferral | No |
| Modular Equipment | Limited Single Modular Approval |
| Composite Device | No |
| Composite Part | No |
| Cognitive Radio | No |
| Authorization Waiver | No |
| Authorization Waiver Approved | No |
| Section 5301 Certification | Yes |
| Related OET Knowledge DataBase Inquiry | No |
| Grant Comments | Output Power listed is conducted. Limited Modular approval for Mobile RF exposure condition. The final product must be professionally installed. Marketing to the General Public is prohibited. Only those antenna type(s) tested with the device or similar antenna(s) with equal or lesser net gain may be used with this transmitter. The use of other antenna requires a Class II Permissive Change filing. End -users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. Class II Permissive Change filing for software enabling 200kHz BW channels, adding new antenna and minor DC circuitry change as described in this filing. (Date of Grant: 12/08/2009) Class II Permissive Change: This Class II Permissive Change is to integrate this module into the MOTOROLA WORKABOUT PRO 4, Models: 7528XUHFN and 7528XPUHFN. The highest reported SAR for extremity (hand) exposure and simultaneous conditions are 2.84W/kg and 3.05W/kg respectively. |
Applications
| Application ID | Date | Purpose |
|---|---|---|
| dIRw+LWCQzcLqMDJk7cOBw== | 2014-11-06 | Class II permissive change or modification of presently authorized equipment |
| P+hRHpTewipJJBFaQmtWrg== | 2009-12-08 | Class II permissive change or modification of presently authorized equipment |
| FF7ul8CZRu2Q96L66Kmvsw== | 2009-12-02 | Class II permissive change or modification of presently authorized equipment |
| 7kK71uns9P4ktGpQqUK3iA== | 2009-07-28 | Class II permissive change or modification of presently authorized equipment |
| 8xmLk1snLgFVJ77X5TTBkA== | 2009-04-10 | Original Equipment |
Equipment Authorization
Grants
TCB Grant - Application P+hRHpTewipJJBFaQmtWrg==
| TCB | GRANT OF EQUIPMENT AUTHORIZATION |
TCB |
| Certification | ||
| Issued Under the Authority of the | ||
| Federal Communications Commission | ||
| By: |
|
Curtis-Straus LLC One Distribution Center Circle Suite #1 Littleton, MA 01460 |
Date of Grant: 12/08/2009 Application Dated: 12/08/2009 |
| Zebra Technologies Corporation |
| 1 Zebra Plaza |
| Holtsville, NY 11742 |
| Attention: Mark Luksich , DMTS, Regulatory Engineering |
| NOT TRANSFERABLE |
| EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below. |
| FCC IDENTIFIER: | UZ721121559 |
| Name of Grantee: | Zebra Technologies Corporation |
| Equipment Class: | Part 15 Spread Spectrum Transmitter |
| Notes: | RFID Reader Module |
| Modular Type: | Limited Single Modular |
| Grant Notes | FCC Rule Parts | Frequency Range (MHZ) | Output Watts | Frequency Tolerance | Emission Designator |
| 15C | 902.75 - 927.25 | 0.826 | |||
| 15C | 902.6 - 927.4 | 0.794 |
| Output Power listed is conducted. Limited Modular approval for Mobile RF exposure condition. The final product must be professionally installed. Marketing to the General Public is prohibited. Only those antenna type(s) tested with the device or similar antenna(s) with equal or lesser net gain may be used with this transmitter. The use of other antenna requires a Class II Permissive Change filing. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End -users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. Class II Permissive Change filing for software enabling 200kHz BW channels, adding new antenna and minor DC circuitry change as described in this filing. |
EAS Grant - Application P+hRHpTewipJJBFaQmtWrg==
| COPY |
FEDERAL COMMUNICATIONS COMMISSION WASHINGTON, D.C. 20554 GRANT OF EQUIPMENT AUTHORIZATION |
COPY |
| Certification |
|
Zebra Technologies Corporation 1 Zebra Plaza Holtsville, NY 11742 United States |
Date of Grant: 12/08/2009 Application Dated: 12/08/2009 |
| Attention: Mark Luksich , DMTS, Regulatory Engineering |
| NOT TRANSFERABLE |
| EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below. |
| FCC IDENTIFIER: | UZ721121559 |
| Name of Grantee: | Zebra Technologies Corporation |
| Equipment Class: | Part 15 Spread Spectrum Transmitter |
| Notes: | RFID Reader Module |
| Modular Type: | Limited Single Modular |
| Grant Notes | FCC Rule Parts | Frequency Range (MHZ) | Output Watts | Frequency Tolerance | Emission Designator |
| 15C | 902.75 - 927.25 | 0.826 | |||
| 15C | 902.6 - 927.4 | 0.794 |
| Output Power listed is conducted. Limited Modular approval for Mobile RF exposure condition. The final product must be professionally installed. Marketing to the General Public is prohibited. Only those antenna type(s) tested with the device or similar antenna(s) with equal or lesser net gain may be used with this transmitter. The use of other antenna requires a Class II Permissive Change filing. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End -users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. Class II Permissive Change filing for software enabling 200kHz BW channels, adding new antenna and minor DC circuitry change as described in this filing. |
| Mail To: | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| TCB | GRANT OF EQUIPMENT AUTHORIZATION |
TCB |
| Certification | ||
| Issued Under the Authority of the | ||
| Federal Communications Commission | ||
| By: |
|
Curtis-Straus LLC One Distribution Center Circle Suite #1 Littleton, MA 01460 |
Date of Grant: 12/02/2009 Application Dated: 12/01/2009 |
| Zebra Technologies Corporation |
| 1 Zebra Plaza |
| Holtsville, NY 11742 |
| Attention: Mark Luksich , DMTS, Regulatory Engineering |
| NOT TRANSFERABLE |
| EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below. |
| FCC IDENTIFIER: | UZ721121559 |
| Name of Grantee: | Zebra Technologies Corporation |
| Equipment Class: | Part 15 Spread Spectrum Transmitter |
| Notes: | RFID Reader Module |
| Modular Type: | Limited Single Modular |
| Grant Notes | FCC Rule Parts | Frequency Range (MHZ) | Output Watts | Frequency Tolerance | Emission Designator |
| 15C | 902.75 - 927.25 | 0.826 | |||
| 15C | 902.6 - 927.4 | 0.794 |
| Output Power listed is conducted. Limited Modular approval for Mobile RF exposure condition. The final product must be professionally installed. Marketing to the General Public is prohibited. Only those antenna type(s) tested with the device or similar antenna(s) with equal or lesser net gain may be used with this transmitter. The use of other antenna requires a Class II Permissive Change filing. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End -users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. Class II Permissive Change filing for software enabling 200kHz BW channels and minor DC circuitry change as described in this filing. |
EAS Grant - Application FF7ul8CZRu2Q96L66Kmvsw==
| COPY |
FEDERAL COMMUNICATIONS COMMISSION WASHINGTON, D.C. 20554 GRANT OF EQUIPMENT AUTHORIZATION |
COPY |
| Certification |
|
Zebra Technologies Corporation 1 Zebra Plaza Holtsville, NY 11742 United States |
Date of Grant: 12/02/2009 Application Dated: 12/01/2009 |
| Attention: Mark Luksich , DMTS, Regulatory Engineering |
| NOT TRANSFERABLE |
| EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below. |
| FCC IDENTIFIER: | UZ721121559 |
| Name of Grantee: | Zebra Technologies Corporation |
| Equipment Class: | Part 15 Spread Spectrum Transmitter |
| Notes: | RFID Reader Module |
| Modular Type: | Limited Single Modular |
| Grant Notes | FCC Rule Parts | Frequency Range (MHZ) | Output Watts | Frequency Tolerance | Emission Designator |
| 15C | 902.75 - 927.25 | 0.826 | |||
| 15C | 902.6 - 927.4 | 0.794 |
| Output Power listed is conducted. Limited Modular approval for Mobile RF exposure condition. The final product must be professionally installed. Marketing to the General Public is prohibited. Only those antenna type(s) tested with the device or similar antenna(s) with equal or lesser net gain may be used with this transmitter. The use of other antenna requires a Class II Permissive Change filing. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End -users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. Class II Permissive Change filing for software enabling 200kHz BW channels and minor DC circuitry change as described in this filing. |
| Mail To: | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| TCB | GRANT OF EQUIPMENT AUTHORIZATION |
TCB |
| Certification | ||
| Issued Under the Authority of the | ||
| Federal Communications Commission | ||
| By: |
|
Timco Engineering, Inc. 849 NW State Road 45 Newberry, FL 32669 |
Date of Grant: 11/06/2014 Application Dated: 11/06/2014 |
| Zebra Technologies Corporation |
| 1 Zebra Plaza |
| Holtsville, NY 11742 |
| Attention: Qianlin Zhou , Regulatory Specialist |
| NOT TRANSFERABLE |
| EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below. |
| FCC IDENTIFIER: | UZ721121559 |
| Name of Grantee: | Zebra Technologies Corporation |
| Equipment Class: | Part 15 Spread Spectrum Transmitter |
| Notes: | RFID Reader Module |
| Modular Type: | Limited Single Modular |
| Grant Notes | FCC Rule Parts | Frequency Range (MHZ) | Output Watts | Frequency Tolerance | Emission Designator |
| 15C | 902.75 - 927.25 | 0.826 | |||
| 15C | 902.6 - 927.4 | 0.794 |
| Output Power listed is conducted. Limited Modular approval for Mobile RF exposure condition. The final product must be professionally installed. Marketing to the General Public is prohibited. Only those antenna type(s) tested with the device or similar antenna(s) with equal or lesser net gain may be used with this transmitter. The use of other antenna requires a Class II Permissive Change filing. End -users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. Class II Permissive Change filing for software enabling 200kHz BW channels, adding new antenna and minor DC circuitry change as described in this filing. (Date of Grant: 12/08/2009) Class II Permissive Change: This Class II Permissive Change is to integrate this module into the MOTOROLA WORKABOUT PRO 4, Models: 7528XUHFN and 7528XPUHFN. The highest reported SAR for extremity (hand) exposure and simultaneous conditions are 2.84W/kg and 3.05W/kg respectively. |
EAS Grant - Application dIRw+LWCQzcLqMDJk7cOBw==
| COPY |
FEDERAL COMMUNICATIONS COMMISSION WASHINGTON, D.C. 20554 GRANT OF EQUIPMENT AUTHORIZATION |
COPY |
| Certification |
|
Zebra Technologies Corporation 1 Zebra Plaza Holtsville, NY 11742 United States |
Date of Grant: 11/06/2014 Application Dated: 11/06/2014 |
| Attention: Qianlin Zhou , Regulatory Specialist |
| NOT TRANSFERABLE |
| EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below. |
| FCC IDENTIFIER: | UZ721121559 |
| Name of Grantee: | Zebra Technologies Corporation |
| Equipment Class: | Part 15 Spread Spectrum Transmitter |
| Notes: | RFID Reader Module |
| Modular Type: | Limited Single Modular |
| Grant Notes | FCC Rule Parts | Frequency Range (MHZ) | Output Watts | Frequency Tolerance | Emission Designator |
| 15C | 902.75 - 927.25 | 0.826 | |||
| 15C | 902.6 - 927.4 | 0.794 |
| Output Power listed is conducted. Limited Modular approval for Mobile RF exposure condition. The final product must be professionally installed. Marketing to the General Public is prohibited. Only those antenna type(s) tested with the device or similar antenna(s) with equal or lesser net gain may be used with this transmitter. The use of other antenna requires a Class II Permissive Change filing. End -users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. Class II Permissive Change filing for software enabling 200kHz BW channels, adding new antenna and minor DC circuitry change as described in this filing. (Date of Grant: 12/08/2009) Class II Permissive Change: This Class II Permissive Change is to integrate this module into the MOTOROLA WORKABOUT PRO 4, Models: 7528XUHFN and 7528XPUHFN. The highest reported SAR for extremity (hand) exposure and simultaneous conditions are 2.84W/kg and 3.05W/kg respectively. |
| Mail To: | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| TCB | GRANT OF EQUIPMENT AUTHORIZATION |
TCB |
| Certification | ||
| Issued Under the Authority of the | ||
| Federal Communications Commission | ||
| By: |
|
Curtis-Straus LLC One Distribution Center Circle Suite #1 Littleton, MA 01460 |
Date of Grant: 04/10/2009 Application Dated: 04/10/2009 |
| Zebra Technologies Corporation |
| 1 Zebra Plaza |
| Holtsville, NY 11742 |
| Attention: Mark Luksich , DMTS, Regulatory Engineering |
| NOT TRANSFERABLE |
| EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below. |
| FCC IDENTIFIER: | UZ721121559 |
| Name of Grantee: | Zebra Technologies Corporation |
| Equipment Class: | Part 15 Spread Spectrum Transmitter |
| Notes: | RFID Reader Module |
| Modular Type: | Limited Single Modular |
| Grant Notes | FCC Rule Parts | Frequency Range (MHZ) | Output Watts | Frequency Tolerance | Emission Designator |
| 15C | 902.75 - 927.25 | 0.826 |
| Output Power listed is conducted. Limited Modular approval for Mobile RF exposure condition. The final product must be professionally installed. Marketing to the General Public is prohibited. Only those antenna type(s) tested with the device or similar antenna(s) with equal or lesser net gain may be used with this transmitter. The use of other antenna requires a Class II Permissive Change filing. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End -users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. |
EAS Grant - Application 8xmLk1snLgFVJ77X5TTBkA==
| COPY |
FEDERAL COMMUNICATIONS COMMISSION WASHINGTON, D.C. 20554 GRANT OF EQUIPMENT AUTHORIZATION |
COPY |
| Certification |
|
Zebra Technologies Corporation 1 Zebra Plaza Holtsville, NY 11742 United States |
Date of Grant: 04/10/2009 Application Dated: 04/10/2009 |
| Attention: Mark Luksich , DMTS, Regulatory Engineering |
| NOT TRANSFERABLE |
| EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below. |
| FCC IDENTIFIER: | UZ721121559 |
| Name of Grantee: | Zebra Technologies Corporation |
| Equipment Class: | Part 15 Spread Spectrum Transmitter |
| Notes: | RFID Reader Module |
| Modular Type: | Limited Single Modular |
| Grant Notes | FCC Rule Parts | Frequency Range (MHZ) | Output Watts | Frequency Tolerance | Emission Designator |
| 15C | 902.75 - 927.25 | 0.826 |
| Output Power listed is conducted. Limited Modular approval for Mobile RF exposure condition. The final product must be professionally installed. Marketing to the General Public is prohibited. Only those antenna type(s) tested with the device or similar antenna(s) with equal or lesser net gain may be used with this transmitter. The use of other antenna requires a Class II Permissive Change filing. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End -users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. |
| Mail To: | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| TCB | GRANT OF EQUIPMENT AUTHORIZATION |
TCB |
| Certification | ||
| Issued Under the Authority of the | ||
| Federal Communications Commission | ||
| By: |
|
Curtis-Straus LLC One Distribution Center Circle Suite #1 Littleton, MA 01460 |
Date of Grant: 07/28/2009 Application Dated: 07/28/2009 |
| Zebra Technologies Corporation |
| 1 Zebra Plaza |
| Holtsville, NY 11742 |
| Attention: Mark Luksich , DMTS, Regulatory Engineering |
| NOT TRANSFERABLE |
| EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below. |
| FCC IDENTIFIER: | UZ721121559 |
| Name of Grantee: | Zebra Technologies Corporation |
| Equipment Class: | Part 15 Spread Spectrum Transmitter |
| Notes: | RFID Reader Module |
| Modular Type: | Limited Single Modular |
| Grant Notes | FCC Rule Parts | Frequency Range (MHZ) | Output Watts | Frequency Tolerance | Emission Designator |
| 15C | 902.75 - 927.25 | 0.826 |
| Output Power listed is conducted. Limited Modular approval for Mobile RF exposure condition. The final product must be professionally installed. Marketing to the General Public is prohibited. Only those antenna type(s) tested with the device or similar antenna(s) with equal or lesser net gain may be used with this transmitter. The use of other antenna requires a Class II Permissive Change filing. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End -users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. Class II Permissive Change filing for PCB change as described in this filing. |
EAS Grant - Application 7kK71uns9P4ktGpQqUK3iA==
| COPY |
FEDERAL COMMUNICATIONS COMMISSION WASHINGTON, D.C. 20554 GRANT OF EQUIPMENT AUTHORIZATION |
COPY |
| Certification |
|
Zebra Technologies Corporation 1 Zebra Plaza Holtsville, NY 11742 United States |
Date of Grant: 07/28/2009 Application Dated: 07/28/2009 |
| Attention: Mark Luksich , DMTS, Regulatory Engineering |
| NOT TRANSFERABLE |
| EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below. |
| FCC IDENTIFIER: | UZ721121559 |
| Name of Grantee: | Zebra Technologies Corporation |
| Equipment Class: | Part 15 Spread Spectrum Transmitter |
| Notes: | RFID Reader Module |
| Modular Type: | Limited Single Modular |
| Grant Notes | FCC Rule Parts | Frequency Range (MHZ) | Output Watts | Frequency Tolerance | Emission Designator |
| 15C | 902.75 - 927.25 | 0.826 |
| Output Power listed is conducted. Limited Modular approval for Mobile RF exposure condition. The final product must be professionally installed. Marketing to the General Public is prohibited. Only those antenna type(s) tested with the device or similar antenna(s) with equal or lesser net gain may be used with this transmitter. The use of other antenna requires a Class II Permissive Change filing. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End -users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. Class II Permissive Change filing for PCB change as described in this filing. |
| Mail To: |