FCC ID UZ7XWING1
XWING1
by Zebra Technologies Corporation
Grantee Code: UZ7 Product Code: XWING1
Latest application date: 2011-08-30
FCC ID Device Details
Operating Frequencies
| Frequency Range | Application Purpose | Final Action Date |
|---|---|---|
| 2412-2472 MHz | Original Equipment | 2011-08-30 |
| 5180-5240 MHz | Original Equipment | 2011-08-30 |
Exhibits
| Document | Type | Available | File |
|---|---|---|---|
| Manual | Users Manual | 2011-08-30 | PDF 153.5 KB |
| Internal photos | Internal Photos | 2011-08-30 | PDF 373.9 KB |
| External photos | External Photos | 2011-08-30 | PDF 446.2 KB |
| FCC ID label | ID Label/Location Info | 2011-08-30 | PDF 37.4 KB |
| FCC ID label location | ID Label/Location Info | 2011-08-30 | PDF 53 KB |
| FCC label location | ID Label/Location Info | 2011-08-30 | PDF 37.4 KB |
| EMC and DFS setup | Test Setup Photos | 2011-08-30 | PDF 468 KB |
| EMC setup | Test Setup Photos | 2011-08-30 | PDF 468 KB |
| DFS report | Test Report | 2011-08-30 | PDF 393.5 KB |
| Test report | Test Report | 2011-08-30 | PDF 1.6 MB |
| Test report 1 | Test Report | 2011-08-30 | PDF 1.5 MB |
| POA | Cover Letter(s) | 2011-08-30 | PDF 21.8 KB |
| Reason for modular approval | Cover Letter(s) | 2011-08-30 | PDF 18.9 KB |
| Request for confidentialty | Cover Letter(s) | 2011-08-30 | PDF 27.4 KB |
| Request for modular approval | Cover Letter(s) | 2011-08-30 | PDF 49.7 KB |
| MPE | RF Exposure Info | 2011-08-30 | PDF 63.7 KB |
Application Information
| Application ID | E+Jaelpt4JfZhdm8FITzfQ== |
|---|---|
| Final Action Date | 2011-08-30 |
| Application Purpose | Original Equipment |
| Applicant FRN | 0007722119 |
| Model | XWING1 |
| Frequency Range | 2412-2472 MHz |
| Equipment Class | DTS - Digital Transmission System |
| Device Description | XWING1 |
| Responsible Party | Mark Luksich, DMTS, Regulatory Engineering, Mark.Luksich@zebra.com  , 631-738-5134 |
| Test Firm | Richard Chen, Bureau Veritas CPS (H.K.) Ltd., Taoyuan Branch, tommy.wu@tw.bureauveritas.com  , 886-3-3183232 |
| TCB Email | hotline@acbcert.com  |
| TCB Scope | A4: UNII devices & low power transmitters using spread spectrum techniques |
| Short-Term Confidentiality | No |
| Long-Term Confidentiality | Yes |
| Grant Deferral | No |
| Modular Equipment | Single Modular Approval |
| Composite Device | Yes |
| Composite Part | No |
| Cognitive Radio | No |
| Authorization Waiver | No |
| Authorization Waiver Approved | No |
| Section 5301 Certification | Yes |
| Related OET Knowledge DataBase Inquiry | No |
| Grant Comments | Power Output listed is conducted. Modular Approval. For EMC compliance the power levels on channels 12 and 13 must be reduced to the levels shown in the filing. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and not be co-located with any other transmitters except in accordance with FCC multi-transmitter product procedures. Only those antenna(s) shown in the filing may be used with this device. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. |
Applications
| Application ID | Date | Purpose |
|---|---|---|
| E+Jaelpt4JfZhdm8FITzfQ== | 2011-08-30 | Original Equipment |
| 71TmdKOpV/KtQUS3EsU8IA== | 2011-08-30 | Original Equipment |
Equipment Authorization
Grants
TCB Grant - Application E+Jaelpt4JfZhdm8FITzfQ==
| TCB | GRANT OF EQUIPMENT AUTHORIZATION |
TCB |
| Certification | ||
| Issued Under the Authority of the | ||
| Federal Communications Commission | ||
| By: |
|
ACB, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 |
Date of Grant: 08/30/2011 Application Dated: 08/29/2011 |
| Zebra Technologies Corporation |
| 1 Zebra Plaza |
| Holtsville, NY 11742 |
| Attention: Mark Luksich , DMTS, Regulatory Engineering |
| NOT TRANSFERABLE |
| EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below. |
| FCC IDENTIFIER: | UZ7XWING1 |
| Name of Grantee: | Zebra Technologies Corporation |
| Equipment Class: | Digital Transmission System |
| Notes: | XWING1 |
| Modular Type: | Single Modular |
| Grant Notes | FCC Rule Parts | Frequency Range (MHZ) | Output Watts | Frequency Tolerance | Emission Designator |
| CC | 15C | 2412.0 - 2472.0 | 0.269 | ||
| CC | 15C | 5745.0 - 5825.0 | 0.166 |
| Power Output listed is conducted. Modular Approval. For EMC compliance the power levels on channels 12 and 13 must be reduced to the levels shown in the filing. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and not be co-located with any other transmitters except in accordance with FCC multi-transmitter product procedures. Only those antenna(s) shown in the filing may be used with this device. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. |
| CC: | This device is certified pursuant to two different Part 15 rules sections. |
EAS Grant - Application E+Jaelpt4JfZhdm8FITzfQ==
| COPY |
FEDERAL COMMUNICATIONS COMMISSION WASHINGTON, D.C. 20554 GRANT OF EQUIPMENT AUTHORIZATION |
COPY |
| Certification |
|
Zebra Technologies Corporation 1 Zebra Plaza Holtsville, NY 11742 United States |
Date of Grant: 08/30/2011 Application Dated: 08/29/2011 |
| Attention: Mark Luksich , DMTS, Regulatory Engineering |
| NOT TRANSFERABLE |
| EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below. |
| FCC IDENTIFIER: | UZ7XWING1 |
| Name of Grantee: | Zebra Technologies Corporation |
| Equipment Class: | Digital Transmission System |
| Notes: | XWING1 |
| Modular Type: | Single Modular |
| Grant Notes | FCC Rule Parts | Frequency Range (MHZ) | Output Watts | Frequency Tolerance | Emission Designator |
| CC | 15C | 2412.0 - 2472.0 | 0.269 | ||
| CC | 15C | 5745.0 - 5825.0 | 0.166 |
| Power Output listed is conducted. Modular Approval. For EMC compliance the power levels on channels 12 and 13 must be reduced to the levels shown in the filing. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and not be co-located with any other transmitters except in accordance with FCC multi-transmitter product procedures. Only those antenna(s) shown in the filing may be used with this device. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. |
| CC: | This device is certified pursuant to two different Part 15 rules sections. |
| Mail To: | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| TCB | GRANT OF EQUIPMENT AUTHORIZATION |
TCB |
| Certification | ||
| Issued Under the Authority of the | ||
| Federal Communications Commission | ||
| By: |
|
ACB, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 |
Date of Grant: 08/30/2011 Application Dated: 08/29/2011 |
| Zebra Technologies Corporation |
| 1 Zebra Plaza |
| Holtsville, NY 11742 |
| Attention: Mark Luksich , DMTS, Regulatory Engineering |
| NOT TRANSFERABLE |
| EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below. |
| FCC IDENTIFIER: | UZ7XWING1 |
| Name of Grantee: | Zebra Technologies Corporation |
| Equipment Class: | Unlicensed National Information Infrastructure TX |
| Notes: | XWING1 |
| Modular Type: | Single Modular |
| Grant Notes | FCC Rule Parts | Frequency Range (MHZ) | Output Watts | Frequency Tolerance | Emission Designator |
| CC | 15E | 5180.0 - 5240.0 | 0.027 | ||
| CC | 15E | 5260.0 - 5320.0 | 0.069 | ||
| CC | 15E | 5500.0 - 5700.0 | 0.072 |
| Power Output listed is conducted. Modular Approval. In the 5150MHz to 5250MHz frequency range this device is restricted to indoor use. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and not be co-located with any other transmitters except in accordance with FCC multi-transmitter product procedures. Only those antenna(s) shown in the filing may be used with this device. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. This device operates as a non-beam forming 1x1 SISO device. |
| CC: | This device is certified pursuant to two different Part 15 rules sections. |
EAS Grant - Application 71TmdKOpV/KtQUS3EsU8IA==
| COPY |
FEDERAL COMMUNICATIONS COMMISSION WASHINGTON, D.C. 20554 GRANT OF EQUIPMENT AUTHORIZATION |
COPY |
| Certification |
|
Zebra Technologies Corporation 1 Zebra Plaza Holtsville, NY 11742 United States |
Date of Grant: 08/30/2011 Application Dated: 08/29/2011 |
| Attention: Mark Luksich , DMTS, Regulatory Engineering |
| NOT TRANSFERABLE |
| EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below. |
| FCC IDENTIFIER: | UZ7XWING1 |
| Name of Grantee: | Zebra Technologies Corporation |
| Equipment Class: | Unlicensed National Information Infrastructure TX |
| Notes: | XWING1 |
| Modular Type: | Single Modular |
| Grant Notes | FCC Rule Parts | Frequency Range (MHZ) | Output Watts | Frequency Tolerance | Emission Designator |
| CC | 15E | 5180.0 - 5240.0 | 0.027 | ||
| CC | 15E | 5260.0 - 5320.0 | 0.069 | ||
| CC | 15E | 5500.0 - 5700.0 | 0.072 |
| Power Output listed is conducted. Modular Approval. In the 5150MHz to 5250MHz frequency range this device is restricted to indoor use. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and not be co-located with any other transmitters except in accordance with FCC multi-transmitter product procedures. Only those antenna(s) shown in the filing may be used with this device. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. This device operates as a non-beam forming 1x1 SISO device. |
| CC: | This device is certified pursuant to two different Part 15 rules sections. |
| Mail To: |