FCC ID VMISWADS-456CAM
IP Camera
by Swann Communications Pty Ltd
Grantee Code: VMI Product Code: SWADS456CAM
Latest application date: 2014-04-23
FCC ID Device Details
Operating Frequencies
| Frequency Range | Application Purpose | Final Action Date |
|---|---|---|
| 2412-2462 MHz | Original Equipment | 2014-04-23 |
Exhibits
| Document | Type | Available | File |
|---|---|---|---|
| Addendum | Users Manual | 2014-04-23 | PDF 21.9 KB |
| Manual | Users Manual | 2014-04-23 | PDF 3 MB |
| Int | Internal Photos | 2014-04-23 | PDF 377.5 KB |
| Ext | External Photos | 2014-04-23 | PDF 407.1 KB |
| Label | ID Label/Location Info | 2014-04-23 | PDF 298.4 KB |
| Setup | Test Setup Photos | 2014-04-23 | PDF 165.2 KB |
| Test Report r1 | Test Report | 2014-04-23 | PDF 751.1 KB |
| Authorization | Cover Letter(s) | 2014-04-23 | PDF 86.3 KB |
| Confid | Cover Letter(s) | 2014-04-23 | PDF 88.8 KB |
| DofC | Cover Letter(s) | 2014-04-23 | PDF 177 KB |
| RFx | RF Exposure Info | 2014-04-23 | PDF 30.7 KB |
| Block Metadata only | Block Diagram | PDF 84.8 KB | |
| Schema Metadata only | Schematics | PDF 2.4 MB | |
| Chipset Metadata only | Operational Description | PDF 148.2 KB | |
| Ops Metadata only | Operational Description | PDF 30.5 KB | |
| RF Module Metadata only | Operational Description | PDF 295.2 KB |
Application Information
| Application ID | 801wM32LApePuM/rTP753Q== |
|---|---|
| Final Action Date | 2014-04-23 |
| Application Purpose | Original Equipment |
| Applicant FRN | 0024573800 |
| Model | SWADS-456CAM |
| Frequency Range | 2412-2462 MHz |
| Equipment Class | DTS - Digital Transmission System |
| Device Description | IP Camera |
| Responsible Party | James Cain, VP Quality Assurance, james@swann.com  , 61 3 84124611 |
| Technical Contact | Mark Koop, Teleconformity, mark.koop@teleconformity.com  , (31)848395876 |
| Test Firm | TOM XUE, Shenzhen Microtest Technology Co.,Ltd., info@51mti.com  , 86-755-88850135 |
| TCB Email | certification@micomlabs.com  |
| TCB Scope | A4: UNII devices & low power transmitters using spread spectrum techniques |
| Short-Term Confidentiality | No |
| Long-Term Confidentiality | Yes |
| Grant Deferral | No |
| Modular Equipment | Does not apply |
| Composite Device | No |
| Composite Part | No |
| Cognitive Radio | No |
| Authorization Waiver | No |
| Authorization Waiver Approved | No |
| Section 5301 Certification | Yes |
| Related OET Knowledge DataBase Inquiry | No |
| Grant Comments | Power Output listed is Conducted. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter within a device, except in accordance with accepted multi-transmitter product procedures. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. |
Applications
| Application ID | Date | Purpose |
|---|---|---|
| 801wM32LApePuM/rTP753Q== | 2014-04-23 | Original Equipment |
Grants
TCB Grant - Application 801wM32LApePuM/rTP753Q==
| TCB | GRANT OF EQUIPMENT AUTHORIZATION |
TCB |
| Certification | ||
| Issued Under the Authority of the | ||
| Federal Communications Commission | ||
| By: |
|
MiCOM Labs 575 Boulder Court Pleasanton, CA 94566 |
Date of Grant: 04/23/2014 Application Dated: 04/23/2014 |
| Swann Communications Pty Ltd |
| Unit 5B |
| 706 Lorimer Street |
| Port Melbourne, 3207 Australia |
| Attention: James Cain , VP Quality Assurance |
| NOT TRANSFERABLE |
| EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below. |
| FCC IDENTIFIER: | VMISWADS-456CAM |
| Name of Grantee: | Swann Communications Pty Ltd |
| Equipment Class: | Digital Transmission System |
| Notes: | IP Camera |
| Grant Notes | FCC Rule Parts | Frequency Range (MHZ) | Output Watts | Frequency Tolerance | Emission Designator |
| 20 | 15C | 2412.0 - 2462.0 | 0.0577 |
| Power Output listed is Conducted. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter within a device, except in accordance with accepted multi-transmitter product procedures. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. |
| 20: | All electrical and mechanical devices employed for spurious radiation suppression, including any modifications made during certification testing, must be incorporated in each unit marketed. |
EAS Grant - Application 801wM32LApePuM/rTP753Q==
| COPY |
FEDERAL COMMUNICATIONS COMMISSION WASHINGTON, D.C. 20554 GRANT OF EQUIPMENT AUTHORIZATION |
COPY |
| Certification |
|
Swann Communications Pty Ltd Unit 5B 706 Lorimer Street Port Melbourne, 3207 Australia |
Date of Grant: 04/23/2014 Application Dated: 04/23/2014 |
| Attention: James Cain , VP Quality Assurance |
| NOT TRANSFERABLE |
| EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below. |
| FCC IDENTIFIER: | VMISWADS-456CAM |
| Name of Grantee: | Swann Communications Pty Ltd |
| Equipment Class: | Digital Transmission System |
| Notes: | IP Camera |
| Modular Type: | Does not apply |
| Grant Notes | FCC Rule Parts | Frequency Range (MHZ) | Output Watts | Frequency Tolerance | Emission Designator |
| 20 | 15C | 2412.0 - 2462.0 | 0.0577 |
| Power Output listed is Conducted. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter within a device, except in accordance with accepted multi-transmitter product procedures. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. |
| 20: | All electrical and mechanical devices employed for spurious radiation suppression, including any modifications made during certification testing, must be incorporated in each unit marketed. |
| Mail To: |