FCC ID YE3600-BE200NG

This device supports 20, 40, 80,160, and 320 MHz BW modes. This module is approved in portable configurations with PIFA reference antenna (4.88 to 5.02 dBi) at 45mm minimum test separation distance. Power Density and SAR testing was performed to demonstrate RF exposure compliance.

This filing meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference antennas: PIFA reference antenna (4.88 to 5.02 dBi), Dipole reference antenna (4.49 to 5.02 dBi) and Monopole reference antenna (4.79 to 4.91 dBi). The minimum gain approved with the UNII-5 to UNII-8 bands is -2.0 dBi. Permissive change as specified under 47 CFR 2.1043 of the FCC rules to rules to installed the single module into a host (LT360PA, LT360xxxxx, x=0-9, A~Z, - or null, or . or /), changed the antenna and the RF power of the module will be reduced by software at the time of production and cannot be adjusted by the end user. Considering these changes, retests were performed on Conducted Emissions at AC Power Line (150kHz-30MHz), Radiated Spurious Emissions, SAR and CBP. All test results are demonstrated to compliance.

This device supports 20, 40, 80,160, and 320 MHz BW modes. This module is approved in portable configurations with PIFA reference antenna (4.88 to 5.02 dBi) at 45mm minimum test separation distance. Power Density and SAR testing was performed to demonstrate RF exposure compliance.

This filing meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference antennas: PIFA reference antenna (4.88 to 5.02 dBi), Dipole reference antenna (4.49 to 5.02 dBi) and Monopole reference antenna (4.79 to 4.91 dBi). The minimum gain approved with the UNII-5 to UNII-8 bands is -2.0 dBi.

Permissive change as specified under 47 CFR 2.1043 of the FCC rules to rules to installed the single module into a host (DT312PA, DT312xxxxx, DT302xxxxx, 302MDxxxxx, DT323xxxxx, 323MDxxxxx, x=0-9, A~Z, - or null, or . or /), changed the antenna and the RF power of the module will be reduced by software at the time of production and cannot be adjusted by the end user. Considering these changes, retests were performed on Conducted Emissions at AC Power Line (150kHz-30MHz), Radiated Spurious Emissions, SAR and CBP. All test results are demonstrated to compliance.

This module is approved in portable configurations with PIFA reference antenna (2.95 dBi) at 43mm minimum test separation distance. SAR testing was performed to demonstrate portable RF compliance for the PIFA antenna.

This filing meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference antennas: PIFA reference antenna (2.95 dBi), Dipole reference antenna (2.95 dBi) and Monopole reference antenna (2.83 dBi).

Permissive change as specified under 47 CFR 2.1043 of the FCC rules to installed the single module into a host (DT302PA, DA302xxxxx, x=0-9, A~Z, - or null, or . or /), changed the antenna and the RF power of the host product will be reduced by software at the time of production and cannot be adjusted by the end user. Considering these changes, retests were performed on Conducted Emissions at AC Power Line (150kHz-30MHz), Radiated Spurious Emissions and SAR test. SAR compliance for body operating conditions is limited to the specific configurations tested for this filing. End-users must be informed of the body requirements to satisfy RF exposure compliance. The highest reported Body SAR value is 1.37W/kg. The highest reported SAR for simultaneous transmission is 1.40W/kg.

This module is approved in portable configurations with PIFA reference antenna (2.95 dBi) at 43mm minimum test separation distance. SAR testing was performed to demonstrate portable RF compliance for the PIFA antenna.

This filing meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference antennas: PIFA reference antenna (2.95 dBi), Dipole reference antenna (2.95 dBi) and Monopole reference antenna (2.83 dBi).

Permissive change as specified under 47 CFR 2.1043 of the FCC rules to installed the single module into a host (DT302PA, DA302xxxxx, x=0-9, A~Z, - or null, or . or /), changed the antenna and the RF power of the host product will be reduced by software at the time of production and cannot be adjusted by the end user. Considering these changes, retests were performed on Conducted Emissions at AC Power Line (150kHz-30MHz), Radiated Spurious Emissions and SAR test. SAR compliance for body operating conditions is limited to the specific configurations tested for this filing. End-users must be informed of the body requirements to satisfy RF exposure compliance. The highest reported Body SAR value is 1.20W/kg. The highest reported SAR for simultaneous transmission is 1.40W/kg.

This module is approved in portable configurations with PIFA reference antenna (2.95 dBi) at 43mm minimum test separation distance. SAR testing was performed to demonstrate portable RF compliance for the PIFA antenna.

This filing meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference antennas: PIFA reference antenna (2.95 dBi), Dipole reference antenna (2.95 dBi) and Monopole reference antenna (2.83 dBi). Permissive change as specified under 47 CFR 2.1043 of the FCC rules to rules to installed the single module into a host (LT360PA, LT360xxxxx, x=0-9, A~Z, - or null, or . or /), changed the antenna and the RF power of the module will be reduced by software at the time of production and cannot be adjusted by the end user. Considering these changes, retests were performed on Conducted Emissions at AC Power Line (150kHz-30MHz), Radiated Spurious Emissions and SAR. All test results are demonstrated to compliance.

This device supports 20, 40, 80,160, and 320 MHz BW modes. This module is approved in portable configurations with PIFA reference antenna (4.88 to 5.02 dBi) at 45mm minimum test separation distance. Power Density and SAR testing was performed to demonstrate RF exposure compliance.

This filing meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference antennas: PIFA reference antenna (4.88 to 5.02 dBi), Dipole reference antenna (4.49 to 5.02 dBi) and Monopole reference antenna (4.79 to 4.91 dBi). The minimum gain approved with the UNII-5 to UNII-8 bands is -2.0 dBi.

Permissive change as specified under 47 CFR 2.1043 of the FCC rules to rules to installed the single module into a host (DT311YA, DT311xxxxx, x=0-9, A~Z, - or null, or . or /), changed the antenna and the RF power of the module will be reduced by software at the time of production and cannot be adjusted by the end user. Considering these changes, retests were performed on Conducted Emissions at AC Power Line (150kHz-30MHz), Radiated Spurious Emissions, SAR and CBP. All test results are demonstrated to compliance.

Modular Approval. Power Output listed is conducted for UNII-1 to UNII-3 and EIRP for UNII-4 bands. UNII-4 band is for indoor operation only. The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. Grantee must provide installation and operating instructions for complying with FCC multi-transmitter product procedures. This module is approved in mobile/portable configurations. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter. Grantee must coordinate with OEM integrator to determine applicable host configurations to ensure RF exposure compliance, including simultaneous transmission SAR requirements according to published KDB 616217 supplement documentation. When all conditions of this filing cannot be met installation of this device into specific final products may require the submission of a permissive change application, containing appropriate data demonstrating compliance, or a new application. This transmitter has 20MHz, 40MHz, 80MHz, 160 MHz bandwidth modes as described in this filing. Device is a client only device containing a 2 x 2 MIMO configuration, enabled for either 2.4 or 5 GHz band operations as described in this filing. OEM/Host integrator must be provided with antenna installation instructions and transmitter operating conditions to satisfy RF exposure compliance. OEM/Host integrator is responsible for complying with the instructions and requirements for each transmitter they choose to integrate into a host product. The highest reported Body and Simultaneous SAR values are 0.77 W/kg and 1.58 W/kg respectively. This module is approved in portable configurations with PIFA reference antenna (5.11 to 5.15 dBi) at 43mm minimum test separation distance. SAR testing was performed to demonstrate portable RF compliance for the PIFA antenna.

This filing meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference antennas: PIFA reference antenna (5.11 to 5.15 dBi), Dipole reference antenna (4.03 to 5.15 dBi) and Monopole reference antenna (4.43 to 4.95 dBi).

This module is approved in portable configurations with PIFA reference antenna (2.95 dBi) at 43mm minimum test separation distance. SAR testing was performed to demonstrate portable RF compliance for the PIFA antenna.

This filing meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference antennas: PIFA reference antenna (2.95 dBi), Dipole reference antenna (2.95 dBi) and Monopole reference antenna (2.83 dBi).

Permissive change as specified under 47 CFR 2.1043 of the FCC rules to rules to installed the single module into a host (DT312PA, DT312xxxxx, DT302xxxxx, 302MDxxxxx, DT323xxxxx, 323MDxxxxx, x=0-9, A~Z, - or null, or . or /), changed the antenna and the RF power of the module will be reduced by software at the time of production and cannot be adjusted by the end user. Considering these changes, retests were performed on Conducted Emissions at AC Power Line (150kHz-30MHz), Radiated Spurious Emissions and SAR. All test results are demonstrated to compliance.

This module is approved in portable configurations with PIFA reference antenna (2.95 dBi) at 43mm minimum test separation distance. SAR testing was performed to demonstrate portable RF compliance for the PIFA antenna.

This filing meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference antennas: PIFA reference antenna (2.95 dBi), Dipole reference antenna (2.95 dBi) and Monopole reference antenna (2.83 dBi).

Permissive change as specified under 47 CFR 2.1043 of the FCC rules to rules to installed the single module into a host (DT301YA, DT301xxxxx, x=0-9, A~Z, - or null, or . or /), changed the antenna and the RF power of the module will be reduced by software at the time of production and cannot be adjusted by the end user. Considering these changes, retests were performed on Conducted Emissions at AC Power Line (150kHz-30MHz), Radiated Spurious Emissions and SAR. All test results are demonstrated to compliance.

Power Output listed is conducted. Modular Approval filing. The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. Grantee must provide installation and operating instructions for complying with FCC multi-transmitter product procedures. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter. End-users and installers must be provided with transmitter operating conditions for satisfying RF exposure compliance. The highest reported Body and Simultaneous SAR values are 0.05 W/kg and 1.36 W/kg respectively. This module is approved in portable configurations with PIFA reference antenna (2.95 dBi) at 43mm minimum test separation distance. SAR testing was performed to demonstrate portable RF compliance for the PIFA antenna.

This filing meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference antennas: PIFA reference antenna (2.95 dBi), Dipole reference antenna (2.95 dBi) and Monopole reference antenna (2.83 dBi).

This module is approved in portable configurations with PIFA reference antenna (2.95 dBi) at 43mm minimum test separation distance. SAR testing was performed to demonstrate portable RF compliance for the PIFA antenna.

This filing meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference antennas: PIFA reference antenna (2.95 dBi), Dipole reference antenna (2.95 dBi) and Monopole reference antenna (2.83 dBi). Permissive change as specified under 47 CFR 2.1043 of the FCC rules to rules to installed the single module into a host (LT360PA, LT360xxxxx, x=0-9, A~Z, - or null, or . or /), changed the antenna and the RF power of the module will be reduced by software at the time of production and cannot be adjusted by the end user. Considering these changes, retests were performed on Conducted Emissions at AC Power Line (150kHz-30MHz), Radiated Spurious Emissions and SAR. All test results are demonstrated to compliance.

This module is approved in portable configurations with PIFA reference antenna (2.95 dBi) at 43mm minimum test separation distance. SAR testing was performed to demonstrate portable RF compliance for the PIFA antenna.

This filing meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference antennas: PIFA reference antenna (2.95 dBi), Dipole reference antenna (2.95 dBi) and Monopole reference antenna (2.83 dBi).

This module is approved in portable configurations with PIFA reference antenna (5.11 to 5.15 dBi) at 43mm minimum test separation distance. SAR testing was performed to demonstrate portable RF compliance for the PIFA antenna.

This filing meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference antennas: PIFA reference antenna (5.11 to 5.15 dBi), Dipole reference antenna (4.03 to 5.15 dBi) and Monopole reference antenna (4.43 to 4.95 dBi).

Permissive change as specified under 47 CFR 2.1043 of the FCC rules to installed the single module into a host (DT323PA, DA323xxxxx, x=0-9, A~Z, - or null, or . or /), changed the antenna and the RF power of the host product will be reduced by software at the time of production and cannot be adjusted by the end user. Considering these changes, retests were performed on Conducted Emissions at AC Power Line (150kHz-30MHz), Radiated Spurious Emissions, DFS and SAR test. SAR compliance for body operating conditions is limited to the specific configurations tested for this filing. End-users must be informed of the body requirements to satisfy RF exposure compliance. The highest reported Body SAR value is 0.38W/kg.

This device supports 20, 40, 80,160, and 320 MHz BW modes. This module is approved in portable configurations with PIFA reference antenna (4.88 to 5.02 dBi) at 45mm minimum test separation distance. Power Density and SAR testing was performed to demonstrate RF exposure compliance.

This filing meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference antennas: PIFA reference antenna (4.88 to 5.02 dBi), Dipole reference antenna (4.49 to 5.02 dBi) and Monopole reference antenna (4.79 to 4.91 dBi). The minimum gain approved with the UNII-5 to UNII-8 bands is -2.0 dBi.

Permissive change as specified under 47 CFR 2.1043 of the FCC rules to rules to installed the single module into a host (DT301YA, DT301xxxxx, x=0-9, A~Z, - or null, or . or /), changed the antenna and the RF power of the module will be reduced by software at the time of production and cannot be adjusted by the end user. Considering these changes, retests were performed on Conducted Emissions at AC Power Line (150kHz-30MHz), Radiated Spurious Emissions, SAR and CBP. All test results are demonstrated to compliance.

This module is approved in portable configurations with PIFA reference antenna (2.95 dBi) at 43mm minimum test separation distance. SAR testing was performed to demonstrate portable RF compliance for the PIFA antenna.

This filing meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference antennas: PIFA reference antenna (2.95 dBi), Dipole reference antenna (2.95 dBi) and Monopole reference antenna (2.83 dBi).

Permissive change as specified under 47 CFR 2.1043 of the FCC rules to rules to installed the single module into a host (DT311YA, DT311xxxxx, x=0-9, A~Z, - or null, or . or /), changed the antenna and the RF power of the module will be reduced by software at the time of production and cannot be adjusted by the end user. Considering these changes, retests were performed on Conducted Emissions at AC Power Line (150kHz-30MHz), Radiated Spurious Emissions and SAR. All test results are demonstrated to compliance.

Power Output listed is conducted. Modular Approval. Power output has been reduced at the upper band-edge channels as shown in filings under this FCC ID. The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. Grantee must provide installation and operating instructions for complying with FCC multi-transmitter product procedures. This module is approved in mobile/portable configurations. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter. Grantee must coordinate with OEM integrator to determine applicable host configurations to ensure RF exposure compliance, including simultaneous transmission SAR requirements according to published KDB 616217 Supplement documentation. When all conditions of this filing cannot be met installation of this device into specific final products may require the submission of a permissive change application, containing appropriate data demonstrating compliance, or a new application. OEM/Host integrator must be provided with antenna installation instructions and transmitter operating conditions to satisfy RF exposure compliance. Device is a client only device containing a 2 x 2 MIMO configuration, enabled for either 2.4 or 5 GHz band operations as described in this filing. OEM/Host integrator is responsible for complying with the instructions and requirements for each transmitter they choose to integrate into a host product. The highest reported Body and Simultaneous SAR values are 0.45 W/kg and 1.36 W/kg respectively. This module is approved in portable configurations with PIFA reference antenna (2.95 dBi) at 43mm minimum test separation distance. SAR testing was performed to demonstrate portable RF compliance for the PIFA antenna.

This filing meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference antennas: PIFA reference antenna (2.95 dBi), Dipole reference antenna (2.95 dBi) and Monopole reference antenna (2.83 dBi).

Permissive change as specified under 47 CFR 2.1043 of the FCC rules to installed the single module into a host (DT302PA, DA302xxxxx, x=0-9, A~Z, - or null, or . or /), changed the antenna and the RF power of the host product will be reduced by software at the time of production and cannot be adjusted by the end user. Considering these changes, retests were performed on Conducted Emissions at AC Power Line (150kHz-30MHz), Radiated Spurious Emissions and SAR test. SAR compliance for body operating conditions is limited to the specific configurations tested for this filing. End-users must be informed of the body requirements to satisfy RF exposure compliance. The highest reported Body SAR value is 1.20W/kg. The highest reported SAR for simultaneous transmission is 1.40W/kg.

This device supports 20, 40, 80,160, and 320 MHz BW modes.

This module is approved in portable configurations with PIFA reference antenna (4.88 to 5.02 dBi) at 45mm minimum test separation distance. Power Density and SAR testing was performed to demonstrate RF exposure compliance.

This filing meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference antennas: PIFA reference antenna (4.88 to 5.02 dBi), Dipole reference antenna (4.49 to 5.02 dBi) and Monopole reference antenna (4.79 to 4.91 dBi). The minimum gain approved with the UNII-5 to UNII-8 bands is -2.0 dBi.

Permissive change as specified under 47 CFR 2.1043 of the FCC rules to installed the single module into a host (DT302PA, DA302xxxxx, x=0-9, A~Z, - or null, or . or /), changed the antenna and the RF power of the host product will be reduced by software at the time of production and cannot be adjusted by the end user. Considering these changes, retests were performed on Conducted Emissions at AC Power Line (150kHz-30MHz), Radiated Spurious Emissions, CBP and SAR test. SAR compliance for body operating conditions is limited to the specific configurations tested for this filing. End-users must be informed of the body requirements to satisfy RF exposure compliance. The highest reported Body SAR value is 1.15W/kg. The highest reported SAR for simultaneous transmission is 1.40W/kg.

This module is approved in portable configurations with PIFA reference antenna (5.11 to 5.15 dBi) at 43mm minimum test separation distance. SAR testing was performed to demonstrate portable RF compliance for the PIFA antenna.

This filing meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference antennas: PIFA reference antenna (5.11 to 5.15 dBi), Dipole reference antenna (4.03 to 5.15 dBi) and Monopole reference antenna (4.43 to 4.95 dBi).

Permissive change as specified under 47 CFR 2.1043 of the FCC rules to installed the single module into a host (DT302PA, DA302xxxxx, x=0-9, A~Z, - or null, or . or /), changed the antenna and the RF power of the host product will be reduced by software at the time of production and cannot be adjusted by the end user. Considering these changes, retests were performed on Conducted Emissions at AC Power Line (150kHz-30MHz), Radiated Spurious Emissions, DFS and SAR test. SAR compliance for body operating conditions is limited to the specific configurations tested for this filing. End-users must be informed of the body requirements to satisfy RF exposure compliance. The highest reported Body SAR value is 1.19W/kg. The highest reported SAR for simultaneous transmission is 1.40W/kg.

This module is approved in portable configurations with PIFA reference antenna (2.95 dBi) at 43mm minimum test separation distance. SAR testing was performed to demonstrate portable RF compliance for the PIFA antenna.

This filing meets MPE requirements of KDB 447498 and can be used in mobile configurations for the following reference antennas: PIFA reference antenna (2.95 dBi), Dipole reference antenna (2.95 dBi) and Monopole reference antenna (2.83 dBi).

Permissive change as specified under 47 CFR 2.1043 of the FCC rules to installed the single module into a host (DT323PA, DA323xxxxx, x=0-9, A~Z, - or null, or . or /), changed the antenna and the RF power of the host product will be reduced by software at the time of production and cannot be adjusted by the end user. Considering these changes, retests were performed on Conducted Emissions at AC Power Line (150kHz-30MHz), Radiated Spurious Emissions and SAR test. SAR compliance for body operating conditions is limited to the specific configurations tested for this filing. End-users must be informed of the body requirements to satisfy RF exposure compliance. The highest reported Body SAR value is 0.74W/kg.