GC750070 Twister Tracks Dual Lane Set Test Report SZEM1806005161CR FCC ID RPT Mindscope Products Inc.

Mindscope Products Inc. Twister Tracks Dual Lane Set

FCC ID Filing: YKGGC750070

Page 1 of GC750070 Twister Tracks Dual Lane Set Test Report SZEM1806005161CR FCC ID  RPT Mindscope Products Inc.
Page 2 of GC750070 Twister Tracks Dual Lane Set Test Report SZEM1806005161CR FCC ID  RPT Mindscope Products Inc.
Page 3 of GC750070 Twister Tracks Dual Lane Set Test Report SZEM1806005161CR FCC ID  RPT Mindscope Products Inc.
Page 4 of GC750070 Twister Tracks Dual Lane Set Test Report SZEM1806005161CR FCC ID  RPT Mindscope Products Inc.
Page 5 of GC750070 Twister Tracks Dual Lane Set Test Report SZEM1806005161CR FCC ID  RPT Mindscope Products Inc.
Page 6 of GC750070 Twister Tracks Dual Lane Set Test Report SZEM1806005161CR FCC ID  RPT Mindscope Products Inc.
Page 7 of GC750070 Twister Tracks Dual Lane Set Test Report SZEM1806005161CR FCC ID  RPT Mindscope Products Inc.
Page 8 of GC750070 Twister Tracks Dual Lane Set Test Report SZEM1806005161CR FCC ID  RPT Mindscope Products Inc.
Page 9 of GC750070 Twister Tracks Dual Lane Set Test Report SZEM1806005161CR FCC ID  RPT Mindscope Products Inc.
Page 10 of GC750070 Twister Tracks Dual Lane Set Test Report SZEM1806005161CR FCC ID  RPT Mindscope Products Inc.
Page 11 of GC750070 Twister Tracks Dual Lane Set Test Report SZEM1806005161CR FCC ID  RPT Mindscope Products Inc.
Page 12 of GC750070 Twister Tracks Dual Lane Set Test Report SZEM1806005161CR FCC ID  RPT Mindscope Products Inc.
Page 13 of GC750070 Twister Tracks Dual Lane Set Test Report SZEM1806005161CR FCC ID  RPT Mindscope Products Inc.
Page 14 of GC750070 Twister Tracks Dual Lane Set Test Report SZEM1806005161CR FCC ID  RPT Mindscope Products Inc.
Page 15 of GC750070 Twister Tracks Dual Lane Set Test Report SZEM1806005161CR FCC ID  RPT Mindscope Products Inc.
Page 16 of GC750070 Twister Tracks Dual Lane Set Test Report SZEM1806005161CR FCC ID  RPT Mindscope Products Inc.
Page 17 of GC750070 Twister Tracks Dual Lane Set Test Report SZEM1806005161CR FCC ID  RPT Mindscope Products Inc.
Page 18 of GC750070 Twister Tracks Dual Lane Set Test Report SZEM1806005161CR FCC ID  RPT Mindscope Products Inc.
Page 19 of GC750070 Twister Tracks Dual Lane Set Test Report SZEM1806005161CR FCC ID  RPT Mindscope Products Inc.
Page 20 of GC750070 Twister Tracks Dual Lane Set Test Report SZEM1806005161CR FCC ID  RPT Mindscope Products Inc.

SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
No. 1 Workshop, M-10, Middle section, Science & Technology Park,
Shenzhen, Guangdong, China 518057
Telephone:
Fax:
Email:
Report No.: SZEM180600516101
Page:
1 of 20
+86 (0) 755 2601 2053
+86 (0) 755 2671 0594
ee.shenzhen@sgs.com
TEST REPORT
Application No.:
SZEM1806005161CR(SGS SZ No.:T51810240003EM)
Applicant:
Mindscope Products Inc.
Address of Applicant:
Buyer/Manufacturer:
9525, Glendale, California, 91226, United States
Mindscope Products Inc.
Supplier/Importer:
Mindscope Products Inc.
Equipment Under Test (EUT):
EUT Name:
Twister Tracks Dual Lane Set, Twister Tracks Dual Lane Add On Vehicles
Model No.:
♣
TTDL11, TTDLS2♣
Please refer to section 2 of this report which indicates which model was
actually tested and which were electrically identical.
FCC ID:
YKGGC750070
Country of Origin:
Country of Destination:
CHINA
Requested Age Grading:
United States
3+
Standard(s) :
47 CFR Part 15, Subpart C 15.227
Date of Receipt:
2018-06-14
Date of Test:
2018-06-15
Date of Issue:
2018-06-20
Test Result:
Pass*
* In the configuration tested, the EUT complied with the standards specified above.
Keny Xu
EMC Laboratory Manager
The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report.
If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new
system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International
Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International
Electrical Approvals in writing.
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM180600516101
Page:
2 of 20
Revision Record
Version
Chapter
01
Date
2018-06-20
Modifier
Remark
Original
Authorized for issue by:
Gebin Sun /Project Engineer
Eric Fu /Reviewer
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM180600516101
Page:
3 of 20
Test Summary
Radio Spectrum Technical Requirement
Item
Standard
Method
Requirement
Result
Antenna Requirement
47 CFR Part 15,
Subpart C 15.227
N/A
47 CFR Part 15, Subpart
C 15.203
Pass
Radio Spectrum Matter Part
Item
Standard
Method
Requirement
Result
20dB Bandwidth
47 CFR Part 15,
Subpart C 15.227
ANSI C63.10 (2013)
Section 6.9
47 CFR Part 15, Subpart
C 15.215
Pass
Field Strength of the
Fundamental Signal
(15.227(a))
47 CFR Part 15,
Subpart C 15.227
ANSI C63.10 (2013)
Section 6.4
47 CFR Part 15, Subpart
C 15.227(a)
Pass
Radiated Emissions
47 CFR Part 15,
Subpart C 15.227
ANSI C63.10 (2013)
Section 6.4&6.5
47 CFR Part 15, Subpart
C 15.227(b) & C 15.209
Pass
Declaration of EUT Family Grouping:
Model No.: TTDL11, TTDLS2
Only the model TTDL11 was tested, since the electrical circuit design, layout, components used,
internal wiring and functions were identical for all the above models, with only difference on model No.,
colour and appearance.
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM180600516101
Page:
4 of 20
Contents
Page
COVER PAGE ............................................................................................................................................1
TEST SUMMARY .......................................................................................................................................3
CONTENTS ................................................................................................................................................4
GENERAL INFORMATION ........................................................................................................................5
4.1
4.2
4.3
4.4
4.5
4.6
4.7
DETAILS OF E.U.T. ...............................................................................................................................5
DESCRIPTION OF SUPPORT UNITS .........................................................................................................5
MEASUREMENT UNCERTAINTY ..............................................................................................................5
TEST LOCATION....................................................................................................................................6
TEST FACILITY......................................................................................................................................6
DEVIATION FROM STANDARDS ...............................................................................................................6
ABNORMALITIES FROM STANDARD CONDITIONS .....................................................................................6
EQUIPMENT LIST ......................................................................................................................................7
RADIO SPECTRUM TECHNICAL REQUIREMENT .................................................................................9
6.1
ANTENNA REQUIREMENT ......................................................................................................................9
6.1.1 Test Requirement: .........................................................................................................................9
6.1.2 Conclusion .....................................................................................................................................9
RADIO SPECTRUM MATTER TEST RESULTS .....................................................................................10
7.1
20DB BANDWIDTH ..............................................................................................................................10
7.1.1 E.U.T. Operation ..........................................................................................................................10
7.1.2 Test Setup Diagram .....................................................................................................................10
7.1.3 Measurement Procedure and Data.............................................................................................10
7.2
FIELD STRENGTH OF THE FUNDAMENTAL SIGNAL (15.227(A))...............................................................12
7.2.1 E.U.T. Operation ..........................................................................................................................12
7.2.2 Test Setup Diagram .....................................................................................................................12
7.2.3 Measurement Procedure and Data.............................................................................................12
7.3
RADIATED EMISSIONS .........................................................................................................................15
7.3.1 E.U.T. Operation ..........................................................................................................................16
7.3.2 Test Setup Diagram .....................................................................................................................16
7.3.3 Measurement Procedure and Data.............................................................................................16
PHOTOGRAPHS ......................................................................................................................................19
8.1
8.2
8.3
FIELD STRENGTH OF THE FUNDAMENTAL SIGNAL (15.227(A)) TEST SETUP ...........................................19
RADIATED EMISSIONS(30MHZ-1GHZ) TEST SETUP .............................................................................19
EUT CONSTRUCTIONAL DETAILS (EUT PHOTOS).................................................................................20
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM180600516101
Page:
5 of 20
General Information
4.1 Details of E.U.T.
Power supply:
3V DC(1.5V x 2 "AA" Size Batteries) for TX
Sample Type:
Portable production
Antenna Type:
Integral
Frequency Range:
27.145MHz
4.2 Description of Support Units
The EUT has been tested as an independent unit.
4.3 Measurement Uncertainty
No.
Item
Measurement Uncertainty
Radio Frequency
± 7.25 x 10-8
Duty cycle
± 0.37%
Occupied Bandwidth
± 3%
RF conducted power
± 0.75dB
RF power density
± 2.84dB
Conducted Spurious emissions
± 0.75dB
RF Radiated power
Radiated Spurious emission test
Temperature test
± 4.5dB (below 1GHz)
± 4.8dB (above 1GHz)
± 4.5dB (Below 1GHz)
± 4.8dB (Above 1GHz)
± 1°C
10
Humidity test
± 3%
11
Supply voltages
± 1.5%
12
Time
± 3%
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM180600516101
Page:
6 of 20
4.4 Test Location
All tests were performed at:
SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen Branch
No. 1 Workshop, M-10, Middle Section, Science & Technology Park, Shenzhen, Guangdong, China.
518057.
Tel: +86 755 2601 2053
Fax: +86 755 2671 0594
No tests were sub-contracted.
4.5 Test Facility
The test facility is recognized, certified, or accredited by the following organizations:
• CNAS (No. CNAS L2929)
CNAS has accredited SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch EMC
Lab to ISO/IEC 17025:2005 General Requirements for the Competence of Testing and Calibration
Laboratories (CNAS-CL01 Accreditation Criteria for the Competence of Testing and Calibration
Laboratories) for the competence in the field of testing.
• A2LA (Certificate No. 3816.01)
SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory is accredited by the
American Association for Laboratory Accreditation(A2LA). Certificate No. 3816.01.
• VCCI
The 3m Fully-anechoic chamber for above 1GHz, 10m Semi-anechoic chamber for below 1GHz,
Shielded Room for Mains Port Conducted Interference Measurement and Telecommunication Port
Conducted Interference Measurement of SGS-CSTC Standards Technical Services Co., Ltd. have
been registered in accordance with the Regulations for Voluntary Control Measures with Registration
No.: G-20026, R-14188, C-12383 and T-11153 respectively.
• FCC –Designation Number: CN1178
SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory has been recognized
as an accredited testing laboratory.
Designation Number: CN1178. Test Firm Registration Number: 406779.
• Industry Canada (IC)
Two 3m Semi-anechoic chambers and the 10m Semi-anechoic chamber of SGS-CSTC Standards
Technical Services Co., Ltd. Shenzhen Branch EMC Lab have been registered by Certification and
Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 4620C-1,
4620C-2, 4620C-3.
4.6 Deviation from Standards
None
4.7 Abnormalities from Standard Conditions
None
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM180600516101
Page:
7 of 20
Equipment List
20dB Bandwidth
Equipment
Manufacturer
Model No
Inventory No
Cal Date
Cal Due Date
DC Power Supply
ZhaoXin
RXN-305D
SEM011-02
2017-09-27
2018-09-26
Spectrum Analyzer
Rohde & Schwarz
FSU43
SEM004-08
2018-04-02
2019-04-01
Measurement Software
JS Tonscend
JS1120-2
BT/WIFI V2.
N/A
N/A
N/A
Coaxial Cable
SGS
N/A
SEM031-01
2017-07-13
2018-07-12
Attenuator
Weinschel Associates
WA41
SEM021-09
N/A
N/A
Signal Generator
KEYSIGHT
N5173B
SEM006-05
2017-09-27
2018-09-26
Power Meter
Rohde & Schwarz
NRVS
SEM014-02
2017-09-27
2018-09-26
Field Strength of the Fundamental Signal (15.227(a))
Equipment
Manufacturer
Model No
Inventory No
Cal Date
Cal Due Date
3m Semi-Anechoic
Chamber
ETS-LINDGREN
N/A
SEM001-01
2017-08-05
2020-08-04
Measurement Software
AUDIX
e3 V8.2014-627
N/A
N/A
N/A
Coaxial Cable
SGS
N/A
SEM025-01
2017-07-13
2018-07-12
EMI Test Receiver
Agilent Technologies
N9038A
SEM004-05
2017-09-27
2018-09-26
BiConiLog Antenna (263000MHz)
ETS-LINDGREN
3142C
SEM003-01
2017-06-27
2020-06-26
Pre-amplifier (0.11300MHz)
Agilent Technologies
8447D
SEM005-01
2018-04-02
2019-04-01
Pre-amplifier
Sonoma Instrument
Co
310N
SEM005-04
2018-04-13
2019-04-12
Active Loop Antenna
ETS-Lindgren
6502
SEM003-08
2017-08-22
2020-08-21
Radiated Emissions(9kHz-30MHz)
Equipment
Manufacturer
Model No
Inventory No
Cal Date
Cal Due Date
10m Semi-Anechoic
Chamber
SAEMC
FSAC1018
SEM001-03
2018-03-31
2021-03-30
Measurement Software
AUDIX
e3 V8.2014-627
N/A
N/A
N/A
Coaxial Cable
SGS
N/A
SEM029-01
2017-07-13
2018-07-12
EMI Test Receiver
(9kHz-3GHz)
Rohde & Schwarz
ESCI
SEM004-01
2018-04-02
2019-04-01
Trilog-Broadband
Antenna(30MHz-1GHz)
Schwarzbeck
VULB9168
SEM003-18
2016-01-26
2019-01-25
Pre-amplifier
Sonoma Instrument
Co
310N
SEM005-04
2018-04-13
2019-04-12
Active Loop Antenna
ETS-Lindgren
6502
SEM003-08
2017-08-22
2020-08-21
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM180600516101
Page:
8 of 20
Radiated Emissions(30MHz-1GHz)
Equipment
Manufacturer
Model No
Inventory No
Cal Date
Cal Due Date
3m Semi-Anechoic
Chamber
ETS-LINDGREN
N/A
SEM001-01
2017-08-05
2020-08-04
Measurement Software
AUDIX
e3 V8.2014-627
N/A
N/A
N/A
Coaxial Cable
SGS
N/A
SEM025-01
2017-07-13
2018-07-12
EMI Test Receiver
Agilent Technologies
N9038A
SEM004-05
2017-09-27
2018-09-26
BiConiLog Antenna (263000MHz)
ETS-LINDGREN
3142C
SEM003-01
2017-06-27
2020-06-26
Pre-amplifier (0.11300MHz)
Agilent Technologies
8447D
SEM005-01
2018-04-02
2019-04-01
General used equipment
Equipment
Manufacturer
Model No
Inventory No
Cal Date
Cal Due Date
Humidity/ Temperature
Indicator
Shanghai
Meteorological
Industry Factory
ZJ1-2B
SEM002-03
2017-09-29
2018-09-28
Humidity/ Temperature
Indicator
Shanghai
Meteorological
Industry Factory
ZJ1-2B
SEM002-04
2017-09-29
2018-09-28
Humidity/ Temperature
Indicator
Mingle
N/A
SEM002-08
2017-09-29
2018-09-28
Barometer
Changchun
Meteorological
Industry Factory
DYM3
SEM002-01
2018-04-08
2019-04-07
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM180600516101
Page:
9 of 20
Radio Spectrum Technical Requirement
6.1 Antenna Requirement
6.1.1 Test Requirement:
47 CFR Part 15, Subpart C 15.203
6.1.2 Conclusion
Standard Requirement:
An intentional radiator shall be designed to ensure that no antenna other than that furnished by the
responsible party shall be used with the device. The use of a antenna that uses a unique coupling to
the intentional radiator, the manufacturer may design the unit permanently attached antenna or of an
so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or
electrical connector is prohibited.
EUT Antenna:
The antenna is integrated on the main PCB and no consideration of replacement.
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM180600516101
Page:
10 of 20
Radio Spectrum Matter Test Results
7.1 20dB Bandwidth
Test Requirement
47 CFR Part 15, Subpart C 15.215
Test Method:
ANSI C63.10 (2013) Section 6.9
7.1.1 E.U.T. Operation
Operating Environment:
Atmospheric Pressure: 1010
Temperature:
24.2 °C
Humidity: 59.4 % RH
Test mode
a:TX mode_Keep the EUT in transmitting with modulation mode.
7.1.2 Test Setup Diagram
mbar
7.1.3 Measurement Procedure and Data
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM180600516101
Page:
11 of 20
Mode:a
* RBW 300 Hz
* VBW 1 kHz
Ref -10 dBm
* Att
10 dB
SWT 780 ms
-10
Marker 1 [T1 ]
-45.31
27.138410000
Marker 2 [T1 ]
-21.74
27.143730000
-20
1 PK
VIEW
-30
-40
D1 -41.74 dBm
Delta 1 [T1 ]
2.50 dB
10.570000000 kHz
dBm
MHz
dBm
MHz
-50
-60
3DB
-70
-80
-90
-100
-110
Center 27.1438 MHz
7 kHz/
Span 70 kHz
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM180600516101
Page:
12 of 20
7.2 Field Strength of the Fundamental Signal (15.227(a))
Test Requirement
Test Method:
Measurement Distance:
Limit:
47 CFR Part 15, Subpart C 15.227(a)
ANSI C63.10 (2013) Section 6.4
3m
≤ 10000 microvolts/meter at 3 meters, the emission limit is based on
measurement instrumentation employing an average Detector:. The
provisions in §15.35 for limiting peak emissions apply.
7.2.1 E.U.T. Operation
Operating Environment:
Temperature:
23.4 °C
Atmospheric Pressure: 1010
Humidity: 56 % RH
Test mode
a:TX mode_Keep the EUT in transmitting with modulation mode.
7.2.2 Test Setup Diagram
mbar
7.2.3 Measurement Procedure and Data
For testing performed with the loop antenna, the center of the loop was positioned 1 m above the
ground and positioned with its plane vertical at the specified distance from the EUT. During testing
the loop was rotated about its vertical axis for maximum response at each azimuth and also
investigated with the loop positioned in the horizontal plane. Only the worst position of vertical was
shown in the report.
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM180600516101
Page:
13 of 20
Mode:a; Polarization:Horizontal
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM180600516101
Page:
14 of 20
Mode:a; Polarization:Vertical
Remark:
1) The field strength is calculated by adding the Antenna Factor, Cable Factor & Preamplifier. The basic
equation with a sample calculation is as follows:
Final Test Level =Receiver Reading + Antenna Factor + Cable Factor – Preamplifier Factor
2) As shown in this section,the field strength limits are based on average limits. However,the peak field
strength of any emission was not exceed the maximum permitted average limits specified. So, only above
measurement data were shown in the report.
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM180600516101
Page:
15 of 20
7.3 Radiated Emissions
Test Requirement
47 CFR Part 15, Subpart C 15.227(b) & C 15.209
Test Method:
ANSI C63.10 (2013) Section 6.4&6.5
Measurement Distance: 3m
Limit:
Frequency(MHz)
Field strength(microvolts/meter)
Measurement distance(meters)
0.009-0.490
2400/F(kHz)
300
0.490-1.705
24000/F(kHz)
30
1.705-30.0
30
30
Remark: The emission limits shown in the above table are based on measurements employing a CISPR
quasi-peak detector except for the frequency bands 9-90kHz and 110-490kHz. Radiated emission limits in
these two bands are based on measurements employing an average detector.
Frequency(MHz)
Field
strength(microvolts/meter)
Measurement
distance(meters)
30-88
100
88-216
150
216-960
200
Above 960
500
Remark: The emission limits shown in the above table are based on measurements employing a
CISPR quasi-peak detector except for above 1000MHz. Radiated emission limits above 1000MHz is
based on measurements employing an average detector.
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM180600516101
Page:
16 of 20
7.3.1 E.U.T. Operation
Operating Environment:
Temperature:
23.4 °C
Atmospheric Pressure: 1010
Humidity: 59.9 % RH
Test mode
a:TX mode_Keep the EUT in transmitting with modulation mode.
7.3.2 Test Setup Diagram
mbar
7.3.3 Measurement Procedure and Data
a. The EUT was placed on the top of a rotating table 0.8 meters above the ground for below 1GHz at
a 3 meter semi-anechoic chamber. The table was rotated 360 degrees to determine the position of
the highest radiation.
b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on
the top of a variable-height antenna tower.
c. The antenna height is varied from one meter to four meters above the ground to determine the
maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set
to make the measurement.
d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was
tuned to heights from 1 meter to 4 meters (for the test frequency of below 30MHz, the antenna was
tuned to heights 1 meter) and the rotatable table was turned from 0 degrees to 360 degrees to find
the maximum reading.
e. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum
Hold Mode.
f. If the emission level of the EUT in peak mode was 10dB lower than the limit specified, then testing
could be stopped and the peak values of the EUT would be reported. Otherwise the emissions that
did not have 10dB margin would be re-tested one by one using peak, quasi-peak or average method
as specified and then reported in a data sheet.
g. The radiation measurements are performed in X, Y, Z axis positioning. And found the X axis
positioning which it is worse case, only the test worst case mode is recorded in the report.
Remark: Level= Read Level+ Cable Loss+ Antenna Factor- Preamp Factor
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM180600516101
Page:
17 of 20
Mode:a; Polarization:Horizontal
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM180600516101
Page:
18 of 20
Mode:a; Polarization:Vertical
Remark:
The disturbance below 30MHz was very low, and the above harmonics were the highest point could be found
when testing, so only the above harmonics had been displayed.
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM180600516101
Page:
19 of 20
Photographs
8.1 Field Strength of the Fundamental Signal (15.227(a)) Test Setup
8.2 Radiated Emissions(30MHz-1GHz) Test Setup
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
SGS-CSTC Standards Technical Services Co., Ltd.
Shenzhen Branch
Report No.: SZEM180600516101
Page:
20 of 20
8.3 EUT Constructional Details (EUT Photos)
Please refer to external and internal photos for details.
- End of the Report -
This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for
electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of
liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention
only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and
obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the
content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s)
tested and such sample(s) are retained for 30 days only.
Download: GC750070 Twister Tracks Dual Lane Set Test Report SZEM1806005161CR FCC ID  RPT Mindscope Products Inc.
Mirror Download [FCC.gov]GC750070 Twister Tracks Dual Lane Set Test Report SZEM1806005161CR FCC ID  RPT Mindscope Products Inc.
Document ID3912341
Application ID/6nMQ4qzSygTbgap33CQHQ==
Document DescriptionTest Report
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeTest Report
Display FormatAdobe Acrobat PDF - pdf
Filesize249.85kB (3123185 bits)
Date Submitted2018-07-04 00:00:00
Date Available2018-07-04 00:00:00
Creation Date2018-07-02 13:45:21
Producing SoftwareGPL Ghostscript 8.64
Document Lastmod2018-07-02 05:45:25
Document TitleSZEM1806005161CR FCC ID RPT
Document CreatorPScript5.dll Version 5.2.2
Document Author: Wendy_Jiang

Source Exif Data [exif.tools]:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Print high-res
Page Count                      : 20
Create Date                     : 2018:07:02 13:45:21+08:00
Title                           : Microsoft Word - SZEM1806005161CR FCC ID  RPT.doc
Producer                        : GPL Ghostscript 8.64
Author                          : Wendy_Jiang
Creator                         : PScript5.dll Version 5.2.2
Modify Date                     : 2018:07:02 05:45:25Z

Facebook Twitter Google+ RSS © FCCID.io 2018