FCC ID Q7V-3F090009X

Wi.232FHSS-250-FCC-R Modular transmitter

by Linx Technologies

Grantee Code: Q7V   Product Code: 3F090009X
Latest application date: 2007-05-30

FCC ID Device Details

FCC IDQ7V-3F090009X
Mirrorsfcc.id | gov | fccid.ai
Grantee CodeQ7V
Product Code3F090009X
Applicant BusinessLinx Technologies 🇺🇸
Related Domains linxtechnologies.com
Equipment ClassWi.232FHSS-250-FCC-R Modular transmitter
Test FirmNebraska Center for Excellence in Electronics

Operating Frequencies

Frequency RangeApplication PurposeFinal Action Date
902.971-926.277 MHzOriginal Equipment2007-05-30

Exhibits

DocumentTypeAvailableFile
Manual revUsers Manual2007-05-30PDF 260.9 KB
Internal photosInternal Photos2007-05-30PDF 426.9 KB
External photosExternal Photos2007-05-30PDF 100.2 KB
External photos 2External Photos2007-05-30PDF 69.2 KB
FCC ID labelID Label/Location Info2007-05-30PDF 46 KB
Set up photosTest Setup Photos2007-05-30PDF 217.2 KB
Test report revisedTest Report2007-05-30PDF 1.2 MB
ATCB commentsCover Letter(s)2007-05-30PDF 56.1 KB
Request for ConfidentialityCover Letter(s)2007-05-30PDF 231.4 KB
Request for Modular ApprovalCover Letter(s)2007-05-30PDF 397.9 KB
rf exposureRF Exposure Info2007-05-30PDF 7.7 KB

Application Information

Application IDx2dYgiCrH+QqsnpdNv/pgA==
Final Action Date2007-05-30
Application PurposeOriginal Equipment
Applicant FRN0009060302
Model-3F090009X
Frequency Range902.971-926.277 MHz
Equipment ClassDSS - Part 15 Spread Spectrum Transmitter
Device DescriptionWi.232FHSS-250-FCC-R Modular transmitter
Responsible PartyShawn Hogan, Director of Engineering, shwnho@linxtechnologies.com , 541-472-3709
Test FirmAaron Steggs, Nebraska Center for Excellence in Electronics, asteggs@nceelabs.com , 4023236233
TCB Emailhotline@AmericanTCB.com
TCB ScopeA4: UNII devices & low power transmitters using spread spectrum techniques
Short-Term ConfidentialityNo
Long-Term ConfidentialityYes
Grant DeferralNo
Modular EquipmentSingle Modular Approval
Composite DeviceNo
Composite PartNo
Cognitive RadioNo
Authorization WaiverNo
Authorization Waiver ApprovedNo
Section 5301 CertificationYes
Related OET Knowledge DataBase InquiryNo
Grant CommentsPower Output listed is Conducted. Modular approval. This module is approved for use in mobile only configurations. This module must be installed by the OEM or OEM integrator. Instructions on installation of this module may not be provided to the end user. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter. The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.

Applications

Application IDDatePurpose
x2dYgiCrH+QqsnpdNv/pgA==2007-05-30Original Equipment

Equipment Authorization

FrequencyOutputRules
902.971-926.277 MHz0.225000015C

Grants

TCB Grant - Application x2dYgiCrH+QqsnpdNv/pgA==

TCB GRANT OF EQUIPMENT
AUTHORIZATION
TCB
Certification
Issued Under the Authority of the
Federal Communications Commission
By:

  ACB, Inc.
6731 Whittier Avenue Suite C110
McLean, VA 22101
Date of Grant: 05/30/2007

Application Dated: 05/29/2007
Linx Technologies
159 Ort Lane
Merlin, OR 97532
 
Attention: Shawn Hogan , Director of Engineering

NOT TRANSFERABLE
EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below.
 
FCC IDENTIFIER:  Q7V-3F090009X
Name of Grantee:  Linx Technologies
Equipment Class: Part 15 Spread Spectrum Transmitter
Notes: Wi.232FHSS-250-FCC-R Modular transmitter
Modular Type: Single Modular
Grant Notes  FCC Rule Parts Frequency
Range (MHZ)
Output
Watts
Frequency
Tolerance
Emission
Designator
15C 902.971  -  926.277 0.225  

Power Output listed is Conducted. Modular approval. This module is approved for use in mobile only configurations. This module must be installed by the OEM or OEM integrator. Instructions on installation of this module may not be provided to the end user. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter. The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.

EAS Grant - Application x2dYgiCrH+QqsnpdNv/pgA==

COPY FEDERAL COMMUNICATIONS
COMMISSION
WASHINGTON, D.C. 20554

GRANT OF EQUIPMENT
AUTHORIZATION
COPY
Certification

Linx Technologies
159 Ort Lane
Merlin, OR 97532
United States
  Date of Grant: 05/30/2007

Application Dated: 05/29/2007
 
Attention: Shawn Hogan , Director of Engineering

NOT TRANSFERABLE
EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below.
 
FCC IDENTIFIER:  Q7V-3F090009X
Name of Grantee:  Linx Technologies
Equipment Class: Part 15 Spread Spectrum Transmitter
Notes: Wi.232FHSS-250-FCC-R Modular transmitter
Modular Type: Single Modular
Grant Notes  FCC Rule Parts Frequency
Range (MHZ)
Output
Watts
Frequency
Tolerance
Emission
Designator
15C 902.971  -  926.277 0.225  

Power Output listed is Conducted. Modular approval. This module is approved for use in mobile only configurations. This module must be installed by the OEM or OEM integrator. Instructions on installation of this module may not be provided to the end user. Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with this transmitter. The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.



Mail To:


EA327173