SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report Samsung Electronics Co Ltd

Samsung Electronics Co Ltd Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+

FCC ID Filing: A3LSMN935KOR
Purchase on Amazon: Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+

Trouble Viewing? See the or view the HTML Version or PDF in frame
Page 1 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 2 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 3 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 4 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 5 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 6 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 7 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 8 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 9 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 10 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 11 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 12 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 13 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 14 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 15 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 16 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 17 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 18 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 19 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 20 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 21 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 22 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 23 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 24 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 25 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 26 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 27 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 28 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 29 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 30 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 31 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 32 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 33 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 34 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 35 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 36 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 37 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 38 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 39 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 40 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 41 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 42 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 43 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 44 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 45 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 46 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 47 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 48 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 49 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 50 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 51 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 52 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 53 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 54 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 55 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 56 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 57 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 58 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 59 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 60 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 61 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Page 62 of SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd

PCTEST ENGINEERING LABORATORY, INC.
7185 Oakland Mills Road, Columbia, MD 21046 USA
Tel. 410.290.6652 / Fax 410.290.6654
http://www.pctestlab.com
MEASUREMENT REPORT
FCC PART 15.247 Bluetooth
Applicant Name:
Samsung Electronics Co., Ltd.
129, Samsung-ro,
Yeongtong-gu, Suwon-si
Gyeonggi-do, 16677, Korea
Date of Testing:
6/2 - 6/28/2016, 7/14/2016
Test Site/Location:
PCTEST Lab. Columbia, MD, USA
Test Report Serial No.:
1M1703230122-08.A3L
FCC ID:
A3LSMN935KOR
APPLICANT:
Samsung Electronics Co., Ltd.
Application Type:
Certification
Model(s):
SM-N935S, SM-N935K, SM-N935L
EUT Type:
Portable Handset
Max. RF Output Power:
14.243 mW (11.54 dBm) Peak Conducted
Frequency Range:
2402 – 2480MHz (Bluetooth for US)
Type of Modulation:
GFSK, /4-DQPSK, 8DPSK
FCC Classification:
FCC Part 15 Spread Spectrum Transmitter (DSS)
FCC Rule Part(s):
Part 15 Subpart C (15.247)
Test Procedure(s):
ANSI C63.10-2013, KDB 648474 D03 v01r04
This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement
report and was tested in accordance with the measurement procedures specified in ANSI C63.10-2013. Test results reported herein relate
only to the item(s) tested.
I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are
correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for
the qualifications of all persons taking them.
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 1 of 62
V 6.3
03/24/2017
T A B L E
O F
C O N T E N T S
FCC PART 15.247 MEASUREMENT REPORT .................................................................................................. 3
1.0
2.0
3.0
INTRODUCTION......................................................................................................................................4
1.1
Scope ............................................................................................................................................................. 4
1.2
PCTEST Test Location ................................................................................................................................... 4
PRODUCT INFORMATION .....................................................................................................................5
2.1
Equipment Description ................................................................................................................................... 5
2.2
Device Capabilities ......................................................................................................................................... 5
2.3
Test Configuration .......................................................................................................................................... 5
2.4
EMI Suppression Device(s)/Modifications ...................................................................................................... 5
DESCRIPTION OF TESTS ......................................................................................................................6
3.1
Evaluation Procedure ..................................................................................................................................... 6
3.2
AC Line Conducted Emissions ....................................................................................................................... 6
3.3
Radiated Emissions ........................................................................................................................................ 7
3.4
Environmental Conditions .............................................................................................................................. 7
4.0
ANTENNA REQUIREMENTS ..................................................................................................................8
5.0
MEASUREMENT UNCERTAINTY ..........................................................................................................9
6.0
TEST EQUIPMENT CALIBRATION DATA ............................................................................................10
7.0
TEST RESULTS ....................................................................................................................................10
8.0
7.1
Summary ...................................................................................................................................................... 11
7.2
20dB Bandwidth Measurement .................................................................................................................... 12
7.3
Output Power Measurement ........................................................................................................................ 18
7.4
Band Edge Compliance ................................................................................................................................ 29
7.5
Carrier Frequency Separation ...................................................................................................................... 32
7.6
Time of Occupancy ...................................................................................................................................... 34
7.7
Number of Hopping Channels ...................................................................................................................... 36
7.8
Conducted Spurious Emissions.................................................................................................................... 38
7.9
Radiated Spurious Emission Measurements – Above 1GHz ....................................................................... 42
7.10
Radiated Restricted Band Edge Measurements....................................................................................... 50
7.11
Radiated Spurious Emissions Measurements – Below 1GHz .................................................................. 54
7.12
Line Conducted Measurement Data ......................................................................................................... 58
CONCLUSION .......................................................................................................................................62
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 2 of 62
V 6.3
03/24/2017
MEASUREMENT REPORT
FCC Part 15.247
§ 2.1033 General Information
APPLICANT:
Samsung Electronics Co., Ltd.
APPLICANT ADDRESS:
129, Samsung-ro,
Yeongtong-gu, Suwon-si, Gyeonggi-do, 16677, Korea
TEST SITE:
PCTEST ENGINEERING LABORATORY, INC.
TEST SITE ADDRESS:
7185 Oakland Mills Road, Columbia, MD 21046 USA
FCC RULE PART(S):
Part 15 Subpart C (15.247)
BASE MODEL:
SM-N935S
FCC ID:
A3LSMN935KOR
FCC CLASSIFICATION:
Method/System:
FCC Part 15 Spread Spectrum Transmitter (DSS)
066AA, 05A93,
Production
Pre-Production
0548E
Frequency Hopping Spread Spectrum (FHSS)
DATE(S) OF TEST:
6/2 - 6/28/2016
TEST REPORT S/N:
1M1703230122-08.A3L
Test Device Serial No.:
Engineering
Test Facility / Accreditations
Measurements were performed at PCTEST Engineering Lab located in Columbia, MD 21046, U.S.A.




PCTEST facility is an FCC registered (PCTEST Reg. No. 159966) test facility with the
site description report on file and has met all the requirements specified in Section 2.948
of the FCC Rules and Industry Canada (2451B-1).
PCTEST Lab is accredited to ISO 17025 by U.S. National Institute of Standards and
Technology (NIST) under the National Voluntary Laboratory Accreditation Program
(NVLAP Lab code: 100431-0) in EMC, FCC and Telecommunications.
PCTEST Lab is accredited to ISO 17025-2005 by the American Association for
Laboratory Accreditation (A2LA) in Specific Absorption Rate (SAR) testing, Hearing Aid
Compatibility (HAC) testing, CTIA Test Plans, and wireless testing for FCC and Industry
Canada Rules.
PCTEST Lab is a recognized U.S. Conformity Assessment Body (CAB) in EMC and
R&TTE (n.b. 0982) under the U.S.-EU Mutual Recognition Agreement (MRA).

PCTEST TCB is a Telecommunication Certification Body (TCB) accredited to ISO/IEC
Guide 65 by the American National Standards Institute (ANSI) in all scopes of FCC Rules
and Industry Canada Standards (RSS).

PCTEST facility is an IC registered (2451B-1) test laboratory with the site description on
file at Industry Canada.

PCTEST is a CTIA Authorized Test Laboratory (CATL) for AMPS, CDMA, and EvDO
wireless devices and for Over-the-Air (OTA) Antenna Performance testing for AMPS,
CDMA, GSM, GPRS, EGPRS, UMTS (W-CDMA), CDMA 1xEVDO, and CDMA 1xRTT.
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 3 of 62
V 6.3
03/24/2017
1.0
1.1
INTRODUCTION
Scope
Measurement and determination of electromagnetic emissions (EMC) of radio frequency devices including
intentional and/or unintentional radiators for compliance with the technical rules and regulations of the Federal
Communications Commission and the Industry Canada Certification and Engineering Bureau.
1.2
PCTEST Test Location
The map below shows the location of the PCTEST LABORATORY, its proximity to the FCC Laboratory, the
Columbia vicinity, the Baltimore-Washington Internt’l (BWI) airport, the city of Baltimore and the Washington,
DC area. (See Figure 1-1).
These measurement tests were conducted at the PCTEST Engineering Laboratory, Inc. facility located at
7185 Oakland Mills Road, Columbia, MD 21046. The site coordinates are 39o 10’23” N latitude and 76o 49’50”
W longitude. The facility is 0.4 miles North of the FCC laboratory, and the ambient signal and ambient signal
strength are approximately equal to those of the FCC laboratory. The detailed description of the measurement
facility was found to be in compliance with the requirements of § 2.948 according to ANSI C63.4-2014 on
January 22, 2015.
Figure 1-1. Map of the Greater Baltimore and Metropolitan Washington, D.C. area
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 4 of 62
V 6.3
03/24/2017
2.0
2.1
PRODUCT INFORMATION
Equipment Description
The Equipment Under Test (EUT) is the Samsung Portable Handset FCC ID: A3LSMN935KOR. The test
data contained in this report pertains only to the emissions due to the EUT’s Bluetooth transmitter.




2.2
This Bluetooth module has been tested by a Bluetooth Qualification Lab, and we confirm the following:
A) The hopping sequence is pseudorandom
B) All channels are used equally on average
C) The receiver input bandwidth equals the transmit bandwidth
D) The receiver hops in sequence with the transmit signal
15.247(g): In accordance with the Bluetooth Industry Standard, the system is designed to comply with all of the
regulations in Section 15.247 when the transmitter is presented with a continuous data (or information) system.
15.247(h): In accordance with the Bluetooth Industry Standard, the system does not coordinate its channels selection/
hopping sequence with other frequency hopping systems for the express purpose of avoiding the simultaneous
occupancy of individual hopping frequencies by multiple transmitters.
15.247(h): The EUT employs Adaptive Frequency Hopping (AFH) which identifies sources of interference namely
devices operating in 802.11 WLAN and excludes them from the list of available channels. The process of re-mapping
reduces the number of test channels from 79 channels to a minimum number of 20 channels.
Device Capabilities
This device contains the following capabilities:
1900 GPRS/EDGE, 850/1900 WCDMA/HSPA, Multi-band LTE, 802.11b/g/n WLAN, 802.11a/n/ac UNII,
Bluetooth (1x, EDR, LE), NFC, ANT+
2.3
Test Configuration
The Samsung Portable Handset FCC ID: A3LSMN935KOR was tested per the guidance of ANSI C63.102013. ANSI C63.10-2013 was also used to reference the appropriate EUT setup for radiated spurious
emissions testing and AC line conducted testing. See Sections 3.2 for AC line conducted emissions test
setups, 3.3 for radiated emissions test setups, and 7.2, 7.3, 7.4, 7.5, 7.6, 7.7, and 7.8 for antenna port
conducted emissions test setups.
This device supports wireless charging capability and, thus, is subject to the test requirements of KDB 648474
D03 v01r04. Additional radiated spurious emission measurements were performed with the EUT lying flat on a
certified wireless charging pad (WCP) while operating under normal conditions in a simulated call or data
transmission configuration. The worst case radiated emissions data is shown in this report.
2.4
EMI Suppression Device(s)/Modifications
No EMI suppression device(s) were added and no modifications were made during testing.
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 5 of 62
V 6.3
03/24/2017
3.0
3.1
DESCRIPTION OF TESTS
Evaluation Procedure
The measurement procedure described in the American National Standard of Procedures for Compliance
Testing of Unlicensed Wireless Devices (ANSI C63.10-2013) was used in the measurement of the Samsung
Portable Handset FCC ID: A3LSMN935KOR.
Deviation from measurement procedure…………………………………………….....................................None
3.2
AC Line Conducted Emissions
The line-conducted facility is located inside a 10'x16'x9' shielded enclosure. The shielded enclosure is
manufactured by ETS Lindgren RF Enclosures. The shielding effectiveness of the shielded room is in
accordance with MIL-Std-285 or NSA 65-5. A 1m x 1.5m wooden table 80cm high is placed 40cm away from
the vertical wall and 80cm away from the sidewall of the shielded room. Two 10kHz-30MHz, 50/50H LineImpedance Stabilization Networks (LISNs) are bonded to the shielded room floor. Power to the LISNs is
filtered by external high-current high-insertion loss power line filters. The external power line filter is an ETS
Lindgren Model LPRX-4X30 (100dB Attenuation, 14kHz-18GHz) and the two EMI/RFI filters are ETS Lindgren
Model LRW-2030-S1 (100dB Minimum Insertion Loss, 14kHz – 10GHz). These filters attenuate ambient signal
noise from entering the measurement lines. These filters are also bonded to the shielded enclosure.
The EUT is powered from one LISN and the support equipment is powered from the second LISN. If the EUT
is a DC-powered device, power will be derived from the source power supply it normally will be powered from
and this supply line(s) will be connected to the second LISN. All interconnecting cables more than 1 meter
were shortened to a 1 meter length by non-inductive bundling (serpentine fashion) and draped over the back
edge of the test table. All cables were at least 40cm above the horizontal reference groundplane. Power
cables for support equipment were routed down to the second LISN while ensuring that that cables were not
draped over the second LISN.
Sufficient time for the EUT, support equipment, and test equipment was allowed in order for them to warm up
to their normal operating condition. The RF output of the LISN was connected to the spectrum analyzer and
exploratory measurements were made to determine the frequencies producing the maximum emission from
the EUT. The spectrum was scanned from 150kHz to 30MHz with a spectrum analyzer. The detector function
was set to peak mode for exploratory measurements while the bandwidth of the analyzer was set to 10kHz.
The EUT, support equipment, and interconnecting cables were arranged and manipulated to maximize each
emission. Once the worst case emissions have been identified, the one EUT cable configuration/arrangement
and mode of operation that produced these emissions is used for final measurements on the same test site.
The analyzer is set to CISPR quasi-peak and average detectors with a 9kHz resolution bandwidth for final
measurements.
Line conducted emissions test results are shown in Section 7.12. The EMI Receiver mode of the Agilent MXE
was used to perform AC line conducted emissions testing.
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 6 of 62
V 6.3
03/24/2017
3.3
Radiated Emissions
The radiated test facilities consisted of an indoor 3 meter semi-anechoic chamber used for final measurements
and exploratory measurements, when necessary. The measurement area is contained within the semianechoic chamber which is shielded from any ambient interference. The test site inside the chamber is a 6m x
5.2m elliptical, obstruction-free area in accordance with Figure 5.7 of Clause 5 in ANSI C63.4-2014. Absorbers
are arranged on the floor between the turn table and the antenna mast in such a way so as to maximize the
reduction of reflections for measurements above 1GHz. A 72.4cm high PVC support structure is placed on top
of the turntable. A 3” (~7.6cm) sheet of high density polystyrene is used as the table top and is placed on top
of the PVC supports to bring the total height of the table to 80cm. For measurements above 1GHz, a high
density expanded polystyrene block is placed on top of the test table to bring the total table height to 1.5m.
For all measurements, the spectrum was scanned through all EUT azimuths and from 1 to 4 meter receive
antenna height using a broadband antenna from 30MHz up to the upper frequency shown in 15.33(b)(1)
depending on the highest frequency generated or used in the device or on which the device operates or tunes.
For frequencies above 1GHz, linearly polarized double ridge horn antennas were used. For frequencies below
30MHz, a calibrated loop antenna was used. When exploratory measurements were necessary, they were
performed at 1 meter test distance inside the semi-anechoic chamber using broadband antennas, broadband
amplifiers, and spectrum analyzers to determine the frequencies and modes producing the maximum
emissions. Sufficient time for the EUT, support equipment, and test equipment was allowed in order for them
to warm up to their normal operating condition. The test set-up was placed on top of the 1 x 1.5 meter table.
The EUT, support equipment, and interconnecting cables were arranged and manipulated to maximize each
emission. Appropriate precaution was taken to ensure that all emissions from the EUT were maximized and
investigated. The system configuration, mode of operation, turntable azimuth, and receive antenna height was
noted for each frequency found.
Final measurements were made in the semi-anechoic chamber using calibrated, linearly polarized broadband
and horn antennas. The test setup was configured to the setup that produced the worst case emissions. The
spectrum analyzer was set to investigate all frequencies required for testing to compare the highest radiated
disturbances with respect to the specified limits. The turntable containing the EUT was rotated through 360
degrees and the height of the receive antenna was varied 1 to 4 meters and stopped at the azimuth and height
producing the maximum emission. Each emission was maximized by changing the orientation of the EUT
through three orthogonal planes and changing the polarity of the receive antenna, whichever produced the
worst-case emissions.
3.4
Environmental Conditions
The temperature is controlled within range of 15oC to 35oC. The relative humidity is controlled within range of
10% to 75%. The atmospheric pressure is monitored within the range 86-106kPa (860-1060mbar).
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 7 of 62
V 6.3
03/24/2017
4.0
ANTENNA REQUIREMENTS
Excerpt from §15.203 of the FCC Rules/Regulations:
“An intentional radiator antenna shall be designed to ensure that no antenna other than that furnished by the
responsible party can be used with the device. The use of a permanently attached antenna or of an antenna
that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the
provisions of this section.”

The antennas of the Samsung Portable Handset are permanently attached.

There are no provisions for connection to an external antenna.
Conclusion:
The Samsung Portable Handset FCC ID: A3LSMN935KOR unit complies with the requirement of §15.203.
Ch.
Frequency (MHz)
00
2402
39
2441
78
2480
Table 4-1. Frequency/ Channel Operations
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 8 of 62
V 6.3
03/24/2017
5.0
MEASUREMENT UNCERTAINTY
The measurement uncertainties shown below were calculated in accordance with the requirements of
ANSI C63.4-2014. All measurement uncertainty values are shown with a coverage factor of k = 2 to indicate a
95% level of confidence. The measurement data shown herein meets or exceeds the UCISPR measurement
uncertainty values specified in CISPR 16-4-2 and, thus, can be compared directly to specified limits to
determine compliance.
Contribution
Expanded Uncertainty (±dB)
Conducted Bench Top
Measurements
1.13
Conducted Disturbance
3.09
Radiated Disturbance (<1GHz)
4.98
Radiated Disturbance (>1GHz)
5.07
Radiated Disturbance (>18GHz)
5.09
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 9 of 62
V 6.3
03/24/2017
6.0
TEST EQUIPMENT CALIBRATION DATA
Test Equipment Calibration is traceable to the National Institute of Standards and Technology (NIST).
Manufacturer
Model
Description
Cal Date
‐
BT2
Bluetooth Cable Set
10/13/2015
‐
RE1
Radiated Emissions Cable Set (UHF/EHF) 3/4/2016
Agilent
8447D
Broadband Amplifier
6/12/2015
Agilent
N9020A
MXA Signal Analyzer
11/5/2015
Agilent
N4010A
Wireless Connectivity Test Set
Com‐Power
PAM‐103
Pre‐Amplifier (1‐1000MHz)
2/26/2016
Emco
3115
Horn Antenna (1‐18GHz)
3/10/2016
ETS Lindgren
3117
1‐18 GHz DRG Horn (Medium)
4/26/2016
ETS Lindgren
3160‐09
18‐26.5 GHz Standard Gain Horn
6/17/2014
K&L
11SH10‐3075/U18000
High Pass Filter
7/18/2015
Pasternack
NMLC‐1
Line Conducted Emissions Cable (NM)
4/28/2016
Rhode & Schwarz
TS‐PR18
Pre‐Amplifier
3/7/2016
Rohde & Schwarz
CMU200
Base Station Simulator
Rohde & Schwarz
ESU40
EMI Test Receiver (40GHz)
7/17/2015
Rohde & Schwarz
TS‐PR18
1‐18 GHz Pre‐Amplifier
3/7/2016
Rohde & Schwarz
TS‐PR26
18‐26.5 GHz Pre‐Amplifier
3/7/2016
Rohde & Schwarz
ESR26
EMI Test Receiver
3/2/2016
Solar Electronics
8012‐50‐R‐24‐BNC
Line Impedance Stabilization Network
7/30/2015
Sunol
JB5
Bi‐Log Antenna (30M ‐ 5GHz)
3/14/2016
Cal Interval
Cal Due
Serial Number
Annual
Biennial
Annual
Annual
N/A
Annual
Biennial
Biennial
Biennial
Annual
Biennial
Annual
N/A
Annual
Annual
Annual
Annual
Biennial
Biennial
10/13/2016
9/4/2016
6/12/2016
11/5/2016
BT2
RE1
2443A01900
US46470561
GB46170464
441112
9704‐5182
125518
135427
11SH10‐3075/U18000‐2
NMLC‐1
101622
836536/0005
100348
100071
100040
101328
310233
A051107
2/26/2017
3/10/2018
4/26/2018
6/17/2016
7/18/2016
4/28/2017
3/7/2017
7/17/2016
3/7/2017
3/7/2017
3/2/2017
7/30/2017
3/14/2018
Table 6-1. Annual Test Equipment Calibration Schedule
Notes:
1. Equipment with a calibration date of “N/A” shown in this list was not used to make direct calibrated
measurements.
2. For equipment listed above that has a calibration date or calibration due date that falls within the test
date range, care was taken to ensure that this equipment was used after the calibration date and
before the calibration due date.
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 10 of 62
V 6.3
03/24/2017
7.0
TEST RESULTS
7.1
Summary
Company Name:
Samsung Electronics Co., Ltd.
FCC ID:
A3LSMN935KOR
Method/System:
Frequency Hopping Spread Spectrum (FHSS)
Number of Channels:
79
FCC Part
Section(s)
Test Description
Test Limit
Test
Condition
Test
Result
Reference
TRANSMITTER MODE (Tx)
15.247(a)(1)(iii)
20dB Bandwidth
N/A
PASS
Section 7.2
15.247(b)(1)
Peak Transmitter Output
Power
 1 Watt if > 75 nonoverlapping channels used
PASS
Section 7.3
15.247(a)(1)
Channel Separation
> 2/3 of 20 dB BW for systems
with Output Power < 125mW
PASS
Section 7.5
15.247(a)(1)(iii)
Number of Channels
> 15 Channels
PASS
Section 7.7
15.247(a)(1)(iii)
Time of Occupancy
< 0.4 sec in 31.6 sec period
PASS
Section 7.6
15.247(d)
Band Edge / Out-of-Band
Emissions
Conducted > 20dBc
PASS
Section 7.4,
Section 7.8
15.205
15.209
General Field Strength Limits
(Restricted Bands and
Radiated Emission Limits)
Emissions in restricted bands
must meet the radiated limits
detailed in 15.209
RADIATED
PASS
Section 7.9,
Section 7.10,
Section 7.11
15.207
AC Conducted Emissions
150kHz – 30MHz
< FCC 15.207 limits
LINE
CONDUCTED
PASS
Section 7.12
CONDUCTED
Table 7-1. Summary of Test Results
Notes:
1) All modes of operation and data rates were investigated. The test results shown in the following sections
represent the worst case emissions.
2) The analyzer plots shown in this section were all taken with a correction table loaded into the analyzer.
The correction table was used to account for the losses of the cables, directional couplers, and attenuators
used as part of the system to maintain a link between the call box and the EUT at all frequencies of
interest.
3) All antenna port conducted emissions testing was performed on a test bench with the antenna port of the
EUT connected to the spectrum analyzer through calibrated cables, attenuators, and couplers.
4) For conducted spurious emissions, automated test software was used to measure emissions and capture
the corresponding plots necessary to show compliance. The measurement software utilized is PCTEST
“BT Auto,” Version 3.3.
5) For radiated band edge, automated test software was used to measure emissions and capture the
corresponding plots necessary to show compliance. The measurement software utilized is PCTEST
“Chamber Automation,” Version 1.1.5.
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 11 of 62
V 6.3
03/24/2017
7.2
20dB Bandwidth Measurement
§15.247 (a.1.iii)
Test Overview and Limit
The bandwidth at 20dB down from the highest in-band spectral density is measured with a spectrum analyzer
connected to the receive antenna while the EUT is operating in transmission mode at the appropriate
frequencies.
Test Procedure Used
ANSI C63.10-2013 – Section 6.9.2
Test Settings
1. The signal analyzers’ automatic bandwidth measurement capability of the spectrum analyzer was
used to perform the 20dB bandwidth measurement. The “X” dB bandwidth parameter was set to
X = 20. The bandwidth measurement was not influenced by any intermediate power nulls in the
fundamental emission.
2. RBW = 1 – 5% OBW
3. VBW ≥ 3 x RBW
4. Reference level set to keep signal from exceeding maximum input mixer level for linear operation.
5. Detector = Peak
6. Trace mode = max hold
7. Sweep = auto couple
8. The trace was allowed to stabilize
Test Setup
The EUT and measurement equipment were set up as shown in the diagram below.
Figure 7-1. Test Instrument & Measurement Setup
Test Notes
None
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 12 of 62
V 6.3
03/24/2017
20dB Bandwidth Test
Results
Frequency
[MHz]
Data
Rate
[Mbps]
2402
1.0
936.00
Pass
2441
1.0
39
955.90
Pass
2480
1.0
78
961.70
Pass
2402
2.0
1324.00
Pass
2441
2.0
39
1342.00
Pass
2480
2.0
78
1341.00
Pass
2402
3.0
1348.00
Pass
2441
3.0
39
1346.00
Pass
2480
3.0
78
1334.00
Pass
Channel
Measured
No.
Bandwidth
[kHz]
Pass/Fail
Table 7-2. Conducted 20dB Bandwidth Measurements
Plot 7-1. 20dB Bandwidth Plot (Bluetooth, 1Mbps – Ch. 0)
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 13 of 62
V 6.3
03/24/2017
Plot 7-2. 20dB Bandwidth Plot (Bluetooth, 1Mbps – Ch. 39)
Plot 7-3. 20dB Bandwidth Plot (Bluetooth, 1Mbps – Ch. 78)
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 14 of 62
V 6.3
03/24/2017
Plot 7-4. 20dB Bandwidth Plot (Bluetooth, 2Mbps – Ch. 0)
Plot 7-5. 20dB Bandwidth Plot (Bluetooth, 2Mbps – Ch. 39)
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 15 of 62
V 6.3
03/24/2017
Plot 7-6. 20dB Bandwidth Plot (Bluetooth, 2Mbps – Ch. 78)
Plot 7-7. 20dB Bandwidth Plot (Bluetooth, 3Mbps – Ch. 0)
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 16 of 62
V 6.3
03/24/2017
Plot 7-8. 20dB Bandwidth Plot (Bluetooth, 3Mbps – Ch. 39)
Plot 7-9. 20dB Bandwidth Plot (Bluetooth, 3Mbps – Ch. 78)
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 17 of 62
V 6.3
03/24/2017
7.3
Output Power Measurement
§15.247 (b.1)
Test Overview and Limits
Measurement is made while the EUT is operating in non-hopping transmission mode. The powers shown
below were measured using a spectrum analyzer with a Bluetooth signaling test set (Agilent Model: N4010A)
used only to maintain a Bluetooth link with the EUT. Average power data is provided to determine the need for
Bluetooth SAR testing according to KDB 447498 D01 v06. Average power measurements are performed using
the analyzer’s “burst power” function with RBW = 3MHz. The burst power function triggers on a single set
burst set to maximum power and measures the maximum average power on the on-time.
The maximum permissible output power is 1 Watt.
Test Procedure Used
ANSI C63.10-2013 – Section 7.8.5
Test Settings
Peak Power Measurement
1. Span = approximately 5x 20dB bandwidth, centered on hopping channel
2. RBW > 20dB bandwidth of emission being measured
3. VBW ≥ RBW
4. Sweep = auto
5. Detector = peak
6. Trace mode = max hold
7. The trace was allowed to stabilize
Test Setup
The EUT and measurement equipment were set up as shown in the diagram below.
Figure 7-2. Test Instrument & Measurement Setup
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 18 of 62
V 6.3
03/24/2017
Note
This unit was tested with all possible data rates and the highest peak power is reported with the unit
transmitting at 1Mbps.
Final results were obtained using calibrated couplers, attenuators and cables. The following formula was used:
Output Power (dBm) = Raw Analyzer Level (dBm) + Cable Loss (dB) + Loss in Directional Coupler/Insertion
Loss (dB)
Peak Conducted
Power
Avg Conducted
Power
[dBm]
[mW]
[dBm]
[mW]
Frequency
[MHz]
Data
Rate
[Mbps]
Channel
No.
2402
1.0
11.16
13.056
11.10
12.871
2441
1.0
39
11.54
14.243
11.48
14.048
2480
1.0
78
11.21
13.198
11.12
12.948
2402
2.0
8.63
7.295
6.44
4.409
2441
2.0
39
9.31
8.525
7.19
5.232
2480
2.0
78
8.15
6.524
5.76
3.767
2402
3.0
8.94
7.827
6.38
4.346
2441
3.0
39
9.67
9.273
7.24
5.295
2480
3.0
78
8.58
7.211
5.95
3.939
Table 7-3. Conducted Output Power Measurements
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 19 of 62
V 6.3
03/24/2017
Plot 7-10. Peak Conducted Power (1Mbps – Ch. 0)
Plot 7-11. Peak Conducted Power (1Mbps – Ch. 39)
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 20 of 62
V 6.3
03/24/2017
Plot 7-12. Peak Conducted Power (1Mbps – Ch. 78)
Plot 7-13. Peak Conducted Power (2Mbps – Ch. 0)
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 21 of 62
V 6.3
03/24/2017
Plot 7-14. Peak Conducted Power (2Mbps – Ch. 39)
Plot 7-15. Peak Conducted Power (2Mbps – Ch. 78)
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 22 of 62
V 6.3
03/24/2017
Plot 7-16. Peak Conducted Power (3Mbps – Ch. 0)
Plot 7-17. Peak Conducted Power (3Mbps – Ch. 39)
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 23 of 62
V 6.3
03/24/2017
Plot 7-18. Peak Conducted Power (3Mbps – Ch. 78)
Plot 7-19. Average Conducted Power (1Mbps – Ch. 0)
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 24 of 62
V 6.3
03/24/2017
Plot 7-20. Average Conducted Power (1Mbps – Ch. 39)
Plot 7-21. Average Conducted Power (1Mbps – Ch. 78)
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 25 of 62
V 6.3
03/24/2017
Plot 7-22. Average Conducted Power (2Mbps – Ch. 0)
Plot 7-23. Average Conducted Power (2Mbps – Ch. 39)
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 26 of 62
V 6.3
03/24/2017
Plot 7-24. Average Conducted Power (2Mbps – Ch. 78)
Plot 7-25. Average Conducted Power (3Mbps – Ch. 0)
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 27 of 62
V 6.3
03/24/2017
Plot 7-26. Average Conducted Power (3Mbps – Ch. 39)
Plot 7-27. Average Conducted Power (3Mbps – Ch. 78)
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 28 of 62
V 6.3
03/24/2017
7.4
Band Edge Compliance
§15.247 (d)
Test Overview and Limits
EUT operates in hopping and non-hopping transmission mode. Measurement is taken at the highest point
located outside of the emission bandwidth. The maximum permissible out-of-band emission level is
20 dBc.
Test Procedure Used
ANSI C63.10-2013 – Section 6.10.4
Test Settings
1. Start and stop frequency were set such that the band edge would be placed in the center of the plot
2. Span was set large enough so as to capture all out of band emissions near the band edge
3. RBW = 100kHz
4. VBW = 300kHz
5. Detector = Peak
6. Number of sweep points ≥ 2 x Span/RBW
7. Trace mode = max hold
8. Sweep time = auto couple
9. The trace was allowed to stabilize
Test Setup
The EUT and measurement equipment were set up as shown in the diagram below.
Figure 7-3. Test Instrument & Measurement Setup
Test Notes
Out of band conducted spurious emissions at the band edge were investigated for all data rates in hopping
and non-hopping modes. The worst case emissions were found with the EUT transmitting at 3 Mbps. Band
edge emissions were also investigated with the EUT transmitting in all data rates. Plots of the worst case
emissions are shown below.
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 29 of 62
V 6.3
03/24/2017
Plot 7-28. Band Edge Plot (Bluetooth with Hopping Disabled, 3 Mbps – Ch. 0)
Plot 7-29. Band Edge Plot (Bluetooth with Hopping Disabled, 3 Mbps – Ch. 78)
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 30 of 62
V 6.3
03/24/2017
Plot 7-30. Band Edge Plot (Bluetooth with Hopping Enabled, 3 Mbps)
Plot 7-31. Band Edge Plot (Bluetooth with Hopping Enabled, 3 Mbps)
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 31 of 62
V 6.3
03/24/2017
7.5
Carrier Frequency Separation
§15.247 (a.1)
Test Overview and Limit
Measurement is made with EUT operating in hopping mode. The minimum permissible channel separation
for this system is 2/3 the value of the 20dB BW.
Test Procedure Used
ANSI C63.10-2013 – Section 7.8.2
Test Settings
1. Span = Wide enough to capture peaks of two adjacent channels
2. RBW = 30% of channel spacing. Adjust as necessary to best identify center of each individual channel
3. VBW ≥ RBW
4. Sweep = Auto
5. Detector = Peak
6. Trace mode = max hold
7. The trace was allowed to stabilize.
8. Marker-delta function used to determine separation between peaks of the adjacent channels
Test Setup
The EUT and measurement equipment were set up as shown in the diagram below.
Figure 7-4. Test Instrument & Measurement Setup
Test Notes
The EUT complies with the minimum channel separation requirement when it is operating in 1x/EDR mode
using 79 channels and when operating in AFH mode using 20 channels.
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 32 of 62
V 6.3
03/24/2017
Min.
Channel Channel
No.
Separation
[MHz]
Frequency
[MHz]
Data
Rate
[Mbps]
2402
1.0
0.624
2441
1.0
39
0.637
2480
1.0
78
0.641
2402
2.0
0.883
2441
2.0
39
0.895
2480
2.0
78
0.894
2402
3.0
0.899
2441
3.0
39
0.897
2480
3.0
78
0.889
Table 7-4. Minimum Channel Separation
Plot 7-32. Channel Spacing Plot (Bluetooth)
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 33 of 62
V 6.3
03/24/2017
7.6
Time of Occupancy
§15.247 (a.1.iii)
Test Overview and Limit
Measurement is made while EUT is operating in hopping mode with the spectrum analyzer set to zero span.
The maximum permissible time of occupancy is 400 ms within a period of 400ms multiplied by the
number of hopping channels employed.
Test Procedure Used
ANSI C63.10-2013 – Section 7.8.4
Test Settings
1. Span = zero span, centered on a hopping channel
2. RBW ≤ channel spacing and >> 1/T, where T is expected dwell time per channel
3. Sweep = as necessary to capture entire dwell time. Second plot may be required to demonstrate two
successive hops on a channel
4. Trigger is set with appropriate trigger delay to place pulse near the center of the plot
5. Detector = peak
6. Trace mode = max hold
7. Marker-delta function used to determine transmit time per hop
Test Setup
The EUT and measurement equipment were set up as shown in the diagram below.
Figure 7-5. Test Instrument & Measurement Setup
Test Notes
None
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 34 of 62
V 6.3
03/24/2017
Plot 7-33. Time of Occupancy Plot (Bluetooth)
Bluetooth Time of Occupancy Calculation
Typically, Bluetooth 1x/EDR mode has a channel hopping rate of 1600 hops/s. Since 1x/EDR modes use 5
transmit and 1 receive slot, for a total of 6 slots, the Bluetooth transmitter is actually hopping at a rate of 1600 /
6 = 266.67 hops/s/slot
400ms x 79 hopping channels = 31.6 sec (Time of Occupancy Limit)
Worst case BT has 266.67 hops/second (for 1x/EDR modes with DH5 operation)
266.67 hops/second / 79 channels = 3.38 hops/second (# of hops/second on one channel)
3.38 hops/second/channel x 31.6 seconds = 106.67 hops (# hops over a 31.6 second period)
106.67 hops x 2.915 ms/channel = 310.94 ms (worst case dwell time for one channel in 1x/EDR
modes)
With AFH, the number of channels is reduced to a minimum of 20 channels and the channel hopping rate is
reduced by 50% to 800 hops/s. AFH mode also uses 6 total slots so the Bluetooth transmitter hops at a rate of
800 / 6 = 133.3 hops/s/slot
400ms x 20 hopping channels = 8 sec (Time of Occupancy Limit)
Worst case BT has 133.3 hops/second/slot (for AFH mode with DH5 operation)
133.3 hops/s / 20 channels = 6.67 hops/second (# of hops/second on one channel)
6.67 hops/s / channel x 8 seconds = 53.34 hops (# hops over an 8 second period)
53.34 hops x 2.915 ms/channel = 155.48 ms (worst case dwell time for one channel in AFH mode)
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 35 of 62
V 6.3
03/24/2017
7.7
Number of Hopping Channels
§15.247 (a.1.iii)
Test Overview and Limit
Measurement is made while EUT is operating in hopping mode. This frequency hopping system must
employ a minimum of 15 hopping channels.
Test Procedure Used
ANSI C63.10-2013 – Section 7.8.3
Test Settings
1. Span = frequency of band of operation (divided into two plots)
2. RBW < 30% of channel spacing or 20dB bandwidth, whichever is smaller.
3. VBW ≥ RBW
4. Sweep = auto
5. Detector = peak
6. Trace mode = max hold
7. Trace was allowed to stabilize
Test Setup
The EUT and measurement equipment were set up as shown in the diagram below.
Figure 7-6. Test Instrument & Measurement Setup
Test Notes
The frequency spectrum was broken up into two sub-ranges to clearly show all of the hopping frequencies. In
AFH mode, this device operates using 20 channels so the requirement for minimum number of hopping
channels is satisfied.
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 36 of 62
V 6.3
03/24/2017
Plot 7-34. Low End Spectrum Channel Hopping Plot (Bluetooth)
Plot 7-35. High End Spectrum Channel Hopping Plot (Bluetooth)
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 37 of 62
V 6.3
03/24/2017
7.8
Conducted Spurious Emissions
§15.247 (d)
Test Overview and Limit
Conducted out-of-band spurious emissions were investigated from 30MHz up to 25GHz to include the 10th
harmonic of the fundamental transmit frequency. The maximum permissible out-of-band emission level is
20 dBc.
Test Procedure Used
ANSI C63.10-2013 – Section 7.8.8
Test Settings
1. Start frequency was set to 30MHz and stop frequency was set to 25GHz (separated into two plots per
channel)
2. RBW = 1MHz* (See note below)
3. VBW = 3MHz
4. Detector = Peak
5. Trace mode = max hold
6. Sweep time = auto couple
7. The trace was allowed to stabilize
Test Setup
The EUT and measurement equipment were set up as shown in the diagram below.
Figure 7-7. Test Instrument & Measurement Setup
Test Notes
Out-of-band conducted spurious emissions were investigated for all data rates and the worst case emissions
were found with the EUT transmitting at N/AMbps. The display line shown in the following plots is the limit at
20dB below the fundamental emission level measured in a 100kHz bandwidth. However, the traces in the
following plots are measured with a 1MHz RBW to reduce test time, so the display line may not necessarily
appear to be 20dB below the level of the fundamental in a 1MHz bandwidth.
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 38 of 62
V 6.3
03/24/2017
Plot 7-36. Conducted Spurious Plot (Bluetooth, N/AMbps – Ch. 0)
Plot 7-37. Conducted Spurious Plot (Bluetooth, N/AMbps – Ch. 0)
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 39 of 62
V 6.3
03/24/2017
Plot 7-38. Conducted Spurious Plot (Bluetooth, N/AMbps – Ch. 39)
Plot 7-39. Conducted Spurious Plot (Bluetooth, N/AMbps – Ch. 39)
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 40 of 62
V 6.3
03/24/2017
Plot 7-40. Conducted Spurious Plot (Bluetooth, N/AMbps – Ch. 78)
Plot 7-41. Conducted Spurious Plot (Bluetooth, N/AMbps – Ch. 78)
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 41 of 62
V 6.3
03/24/2017
7.9
Radiated Spurious Emission Measurements – Above 1GHz
§15.205 §15.209 §15.247 (d)
Test Overview and Limit
All out of band radiated spurious emissions are measured with a spectrum analyzer connected to a receive
antenna while the EUT is operating at maximum power and at the appropriate frequencies. Only the radiated
emissions of the configuration that produced the worst case emissions are reported in this section.
All out of band emissions appearing in a restricted band as specified in Section 15.205 of the Title 47
CFR must not exceed the limits shown in Table 7-5 per Section 15.209.
Frequency
Field Strength
[V/m]
Measured Distance
[Meters]
500
Above 960.0 MHz
Table 7-5. Radiated Limits
Test Procedure Used
ANSI C63.10-2013 – Section 6.6.4.3
Test Settings
Average Field Strength Measurements per Section 4.1.4.2.3 of ANSI C63.10-2013
1. Analyzer center frequency was set to the frequency of the radiated spurious emission of interest
2. RBW = 1MHz
3. VBW = 1kHz  1/Hz, where  = pulse width in seconds
4. Averaging type was set to RMS to ensure that video filtering was applied in the power domain
5. Detector = peak
6. Sweep time = auto
7. Trace mode = max hold
8. Trace was allowed to stabilize
Peak Field Strength Measurements per Section 4.1.4.2.2 of ANSI C63.10-2013
1. Analyzer center frequency was set to the frequency of the radiated spurious emission of interest
2. RBW is set depending on measurement frequency, as specified in Table 7-6 below
3. VBW = 3MHz
4. Detector = peak
5. Sweep time = auto couple
6. Trace mode = max hold
7. Trace was allowed to stabilize
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 42 of 62
V 6.3
03/24/2017
Frequency
RBW
9 – 150kHz
200 – 300Hz
0.15 – 30MHz
9 – 10kHz
30 – 1000MHz
100 – 120kHz
> 1000MHz
1MHz
Table 7-6. RBW as a Function of Frequency
Test Setup
The EUT and measurement equipment were set up as shown in the diagram below.
Figure 7-8. Radiated Test Setup >1GHz
Test Notes
1. All emissions lying in restricted bands specified in §15.205 are below the limit shown in Table 7-5.
2. No significant radiated emissions were found in the 2310 - 2390MHz restricted band.
3. The antenna is manipulated through typical positions, polarity and length during the tests. The EUT is
manipulated through three orthogonal planes.
4. This unit was tested with its standard battery.
5. The spectrum is measured from 9kHz to the 10th harmonic and the worst-case emissions are reported.
6. The duty cycle correction factor was not applied to noise floor measurements.
7. The wide spectrum spurious emissions plots shown on the following pages are used only for the purpose
of emission identification. Any emissions found to be within 20dB of the limit are fully investigated and the
results are shown in this section.
8. The "-" shown in the following RSE tables are used to denote a noise floor measurement.
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 43 of 62
V 6.3
03/24/2017
Sample Calculation
Field Strength Level [dBV/m] = Analyzer Level [dBm] + 107 + AFCL [dB/m] + Duty Cycle Correction [dB]
AFCL [dB/m] = Antenna Factor [dB/m] + Cable Loss [dB]
Margin [dB] = Field Strength Level [dBV/m] – Limit [dBV/m]
Duty Cycle Correction Factor Calculation
Channel hop rate = 800 hops/second (AFH Mode)
Adjusted channel hop rate for DH5 mode = 133.33 hops/second
Time per channel hop = 1 / 133.33 hops/second = 7.50 ms
Time to cycle through all channels = 7.50 x 20 channels = 150 ms
Number of times transmitter hits on one channel = 100 ms / 150 ms = 1 time(s)
Worst case dwell time = 7.5 ms
Duty cycle correction factor = 20log10(7.5ms/100ms) = -22.5 dB
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 44 of 62
V 6.3
03/24/2017
Radiated Spurious Emission Measurements
§15.205 §15.209 §15.247 (d)
Plot 7-42. Radiated Spurious Plot above 1GHz (BT – Ch. 0, Ant. Pol. H)
Plot 7-43. Radiated Spurious Plot above 1GHz (BT – Ch. 0, Ant. Pol. V)
Plot 7-44. Radiated Spurious Plot above 1GHz (BT – Ch. 39, Ant. Pol. H)
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 45 of 62
V 6.3
03/24/2017
Plot 7-45. Radiated Spurious Plot above 1GHz (BT – Ch. 39, Ant. Pol. V)
Plot 7-46. Radiated Spurious Plot above 1GHz (BT – Ch. 78, Ant. Pol. H)
Plot 7-47. Radiated Spurious Plot above 1GHz (BT – Ch. 78, Ant. Pol. V)
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 46 of 62
V 6.3
03/24/2017
Radiated Spurious Emissions Measurements (Above 18GHz)
§15.209
Plot 7-48. Radiated Spurious Plot above 18GHz (Pol. H)
Plot 7-49. Radiated Spurious Plot above 18GHz (Pol. V)
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 47 of 62
V 6.3
03/24/2017
Radiated Spurious Emission Measurements
§15.205 §15.209 §15.247 (d)
Worst Case Mode:
Worst Case Data Rate:
Measurement Distance:
Operating Frequency:
Channel:
Frequency
[MHz]
Bluetooth
1 Mbps
3 Meters
2402MHz
Ant. Antenna Turntable Analyzer
Detector Pol. Height
Azimuth
Level
[H/V]
[cm]
[degree]
[dBm]
AFCL
[dB/m]
Duty Cycle
Field
Limit
Margin
Correction Strength
[dBμV/m]
[dB]
[dB]
[dBμV/m]
4804.00
Avg
-110.07
40.43
0.00
37.36
53.98
-16.62
4804.00
Peak
-97.82
40.43
0.00
49.61
73.98
-24.37
12010.00
Avg
-109.34
51.20
0.00
48.85
53.98
-5.12
12010.00
Peak
-99.75
51.20
0.00
58.44
73.98
-15.53
Table 7-7. Radiated Measurements
Worst Case Mode:
Worst Case Data Rate:
Measurement Distance:
Operating Frequency:
Channel:
Frequency
[MHz]
Bluetooth
1 Mbps
3 Meters
2441MHz
39
Ant. Antenna Turntable Analyzer
Detector Pol. Height
Azimuth
Level
[H/V]
[cm]
[degree]
[dBm]
AFCL
[dB/m]
Duty Cycle
Field
Limit
Margin
Correction Strength
[dBμV/m]
[dB]
[dB]
[dBμV/m]
4882.00
Avg
-110.80
39.94
0.00
36.14
53.98
-17.84
4882.00
Peak
-96.62
39.94
0.00
50.32
73.98
-23.66
7323.00
Avg
-112.57
43.81
0.00
38.23
53.98
-15.75
7323.00
Peak
-98.74
43.81
0.00
52.06
73.98
-21.92
12205.00
Avg
-109.49
51.21
0.00
48.72
53.98
-5.26
12205.00
Peak
-97.16
51.21
0.00
61.05
73.98
-12.93
Table 7-8. Radiated Measurements
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 48 of 62
V 6.3
03/24/2017
Radiated Spurious Emission Measurements
§15.205 §15.209 §15.247 (d)
Worst Case Mode:
Worst Case Data Rate:
Measurement Distance:
Operating Frequency:
Channel:
Frequency
[MHz]
Bluetooth
1 Mbps
3 Meters
2480MHz
78
Ant. Antenna Turntable Analyzer
Detector Pol. Height
Azimuth
Level
[H/V]
[cm]
[degree]
[dBm]
AFCL
[dB/m]
Duty Cycle
Field
Limit
Margin
Correction Strength
[dBμV/m]
[dB]
[dB]
[dBμV/m]
4960.00
Avg
-110.83
40.02
0.00
36.19
53.98
-17.79
4960.00
Peak
-98.40
40.02
0.00
48.62
73.98
-25.36
7440.00
Avg
-112.71
44.42
0.00
38.70
53.98
-15.27
7440.00
Peak
-99.63
44.42
0.00
51.78
73.98
-22.19
12400.00
Avg
-109.34
51.65
0.00
49.31
53.98
-4.67
12400.00
Peak
-96.63
51.65
0.00
62.02
73.98
-11.96
Table 7-9. Radiated Measurements
Worst Case Mode:
Worst Case Data Rate:
Measurement Distance:
Operating Frequency:
Channel:
Frequency
[MHz]
Bluetooth
1 Mbps
3 Meters
2480MHz
78
Ant. Antenna Turntable Analyzer
Detector Pol. Height
Azimuth
Level
[H/V]
[cm]
[degree]
[dBm]
AFCL
[dB/m]
Duty Cycle
Field
Limit
Margin
Correction Strength
[dBμV/m]
[dB]
[dB]
[dBμV/m]
4960.00
Avg
-110.64
40.02
0.00
36.38
53.98
-17.60
4960.00
Peak
-100.50
40.02
0.00
46.52
73.98
-27.46
7440.00
Avg
-112.53
44.42
0.00
38.88
53.98
-15.09
7440.00
Peak
-100.47
44.42
0.00
50.94
73.98
-23.03
12400.00
Avg
-109.39
51.65
0.00
49.26
53.98
-4.72
12400.00
Peak
-99.94
51.65
0.00
58.71
73.98
-15.27
Table 7-10. Radiated Measurements with WCP
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 49 of 62
V 6.3
03/24/2017
7.10
Radiated Restricted Band Edge Measurements
§15.205 §15.209 §15.247 (d)
The radiated restricted band edge measurements are measured with an EMI test receiver connected to the
receive antenna while the EUT is transmitting. Two different amplitude offsets were used depending on
whether peak or average measurements were measured. The average measurements use a duty cycle
correction factor (DCCF).
The amplitude offset shown in the following plots for average measurements was calculated using the formula:
Offset (dB) = (Antenna Factor + Cable Loss + 10 dB Attenuator) – Preamplifier Gain + DCCF
Worst Case Mode:
Bluetooth
Worst Case Data Rate:
1 Mbps
Measurement Distance:
3 Meters
Operating Frequency:
2480MHz
Channel:
78
* RBW 1 MHz
* VBW 3 kHz
Ref
* Att
99.8 dBµV
Offset
0 dB
SWT 10 ms
Marker 1 [T1 ]
37.46 dBµV
2.483500000 GHz
-7.2 dB
LIMIT CHECK
PASS
SGL
90
1 PK
MAXH
80
LVL
70
PS
60
FCC15CAV
50
SWP
100 of
100
3DB
AC
40
30
20
10
-0.2
Center
2.4835 GHz
Date: 14.JUL.2016
1 MHz/
Span
10 MHz
20:01:56
Plot 7-50. Radiated Restricted Upper Band Edge Measurement (Average)
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 50 of 62
V 6.3
03/24/2017
Radiated Restricted Band Edge Measurements
§15.205 §15.209 §15.247 (d)
The amplitude offset shown in the following plots for peak measurements was calculated using the formula:
Offset (dB) = (Antenna Factor + Cable Loss + 10 dB Attenuator) – Preamplifier Gain
* RBW 1 MHz
* VBW 3 MHz
Ref
122.3 dBµV
120 Offset
* Att
0 dB
SWT 2.5 ms
Marker 2 [T2 ]
63.48 dBµV
2.483516026 GHz
15.3 dB
LIMIT CHECK
PASS
110
SGL
100
LVL
2 PK
MAXH
90
PS
80
FCC15CPK
70
3DB
AC
60
50
40
30
Center
2.4835 GHz
Date: 14.JUL.2016
1 MHz/
Span
10 MHz
20:02:14
Plot 7-51. Radiated Restricted Upper Band Edge Measurement (Peak)
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 51 of 62
V 6.3
03/24/2017
Radiated Restricted Band Edge Measurements
§15.205 §15.209 §15.247 (d)
The amplitude offset shown in the following plots for average measurements was calculated using the formula:
Offset (dB) = (Antenna Factor + Cable Loss + 10 dB Attenuator) – Preamplifier Gain + DCCF
Worst Case Mode:
Bluetooth
Worst Case Data Rate:
1 Mbps
Measurement Distance:
3 Meters
Operating Frequency:
2480MHz
Channel:
78
* RBW 1 MHz
* VBW 1 kHz
Ref
95.9 dBµV
Offset
* Att
10 dB
SWT 50 ms
Marker 1 [T1 ]
31.81 dBµV
2.483500000 GHz
-14.1 dB
LIMIT CHECK
90
PASS
1 PK
MAXH
80
LVL
70
60
PS
FCC15CAV
50
40
3DB
AC
30
20
10
Center
2.4835 GHz
Date: 14.JUN.2016
2 MHz/
Span
20 MHz
12:11:57
Plot 7-52. Radiated Restricted Upper Band Edge Measurement with WCP (Average)
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 52 of 62
V 6.3
03/24/2017
Radiated Restricted Band Edge Measurements
§15.205 §15.209 §15.247 (d)
The amplitude offset shown in the following plots for peak measurements was calculated using the formula:
Offset (dB) = (Antenna Factor + Cable Loss + 10 dB Attenuator) – Preamplifier Gain
* RBW 1 MHz
* VBW 3 MHz
Ref
118.4 dBµV
Offset
* Att
10 dB
SWT 5 ms
Marker 1 [T1 ]
60.10 dBµV
2.483500000 GHz
8.4 dB
LIMIT CHECK
PASS
110
1 PK
MAXH
100
LVL
90
PS
80
FCC15CPK
70
3DB
AC
60
50
40
30
20
Center
2.4835 GHz
Date: 14.JUN.2016
2 MHz/
Span
20 MHz
12:13:04
Plot 7-53. Radiated Restricted Upper Band Edge Measurement with WCP (Peak)
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 53 of 62
V 6.3
03/24/2017
7.11
Radiated Spurious Emissions Measurements – Below 1GHz
§15.209
Test Overview and Limit
All out of band radiated spurious emissions are measured with a spectrum analyzer connected to a receive
antenna while the EUT is operating at its maximum duty cycle, at maximum power, and at the appropriate
frequencies. All data rates and modes were investigated for radiated spurious emissions. Only the radiated
emissions of the configuration that produced the worst case emissions are reported in this section.
All out of band emissions appearing in a restricted band as specified in Section 15.205 of the Title 47
CFR must not exceed the limits shown in Table 7-11 per Section 15.209.
Frequency
Field Strength
[V/m]
Measured Distance
[Meters]
0.009 – 0.490 MHz
0.490 – 1.705 MHz
1.705 – 30.00 MHz
30.00 – 88.00 MHz
88.00 – 216.0 MHz
216.0 – 960.0 MHz
Above 960.0 MHz
2400/F (kHz)
24000/F (kHz)
30
100
150
200
500
300
30
30
Table 7-11. Radiated Limits
Test Procedures Used
ANSI C63.10-2013
Test Settings
Quasi-Peak Field Strength Measurements
1. Analyzer center frequency was set to the frequency of the radiated spurious emission of interest
2. RBW = 120kHz (for emissions from 30MHz – 1GHz)
3. Detector = quasi-peak
4. Sweep time = auto couple
5. Trace mode = max hold
6. Trace was allowed to stabilize
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 54 of 62
V 6.3
03/24/2017
Test Setup
The EUT and measurement equipment were set up as shown in the diagrams below.
Figure 7-9. Radiated Test Setup < 30Mhz
Figure 7-10. Radiated Test Setup < 1GHz
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 55 of 62
V 6.3
03/24/2017
Test Notes
1. All emissions lying in restricted bands specified in §15.205 are below the limit shown in Table 7-11.
2. The broadband receive antenna is manipulated through vertical and horizontal polarizations during the
tests. The EUT is manipulated through three orthogonal planes.
3. This unit was tested with its standard battery.
4. The spectrum is investigated using a peak detector and final measurements are recorded using
CISPR quasi peak detector. The worst-case emissions are reported however emissions whose levels
were not within 20dB of the respective limits were not reported.
5. Emissions were measured at a 3 meter test distance.
6. Emissions are investigated while operating on the center channel of the mode, band, and modulation
that produced the worst case results during the transmitter spurious emissions testing.
7. No spurious emissions were detected within 20dB of the limit below 30MHz.
8. The results recorded using the broadband antenna is known to correlate with the results obtained by
using a tuned dipole with an acceptable degree of accuracy. The VSWR for the measurement antenna
was found to be less than 2:1.
9. The wide spectrum spurious emissions plots shown on the following pages are used only for the
purpose of emission identification. There were no emissions detected in the 30MHz – 1GHz frequency
range, as shown in the subsequent plots.
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 56 of 62
V 6.3
03/24/2017
Radiated Spurious Emissions Measurements (Below 1GHz)
§15.209
Plot 7-54. Radiated Spurious Plot below 1GHz (Pol. H)
Plot 7-55. Radiated Spurious Plot below 1GHz (Pol. V)
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 57 of 62
V 6.3
03/24/2017
7.12
Line Conducted Measurement Data
§15.207
Test Overview and Limit
All AC line conducted spurious emissions are measured with a receiver connected to a grounded LISN while
the EUT is operating at its maximum duty cycle, at maximum power, and at the appropriate frequencies. All
data rates and modes were investigated for conducted spurious emissions. Only the conducted emissions of
the configuration that produced the worst case emissions are reported in this section.
All conducted emissions must not exceed the limits shown in the table below, per Section 15.207.
Frequency of emission
(MHz)
Conducted Limit (dBV)
Quasi-peak
66 to 56*
56
60
0.15 – 0.5
0.5 – 5
5 – 30
Average
56 to 46*
46
50
Table 7-12. Conducted Limits
*Decreases with the logarithm of the frequency.
Test Procedures Used
ANSI C63.10-2013, Section 6.2
Test Settings
Quasi-Peak Field Strength Measurements
1. Analyzer center frequency was set to the frequency of the spurious emission of interest
2. RBW = 9kHz (for emissions from 150kHz – 30MHz)
3. Detector = quasi-peak
4. Sweep time = auto couple
5. Trace mode = max hold
6. Trace was allowed to stabilize
Average Field Strength Measurements
1. Analyzer center frequency was set to the frequency of the spurious emission of interest
2. RBW = 9kHz (for emissions from 150kHz – 30MHz)
3. Detector = RMS
4. Sweep time = auto couple
5. Trace mode = max hold
6. Trace was allowed to stabilize
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 58 of 62
V 6.3
03/24/2017
Test Setup
The EUT and measurement equipment were set up as shown in the diagram below.
Figure 7-11. Test Instrument & Measurement Setup
Test Notes
1.
All modes of operation were investigated and the worst-case emissions are reported using mid channel.
The emissions found were not affected by the choice of channel used during testing.
2.
The limit for an intentional radiator from 150kHz to 30MHz are specified in 15.207.
3.
Corr. (dB) = Cable loss (dB) + LISN insertion factor (dB)
4.
QP/AV Level (dBV) = QP/AV Analyzer/Receiver Level (dBV) + Corr. (dB)
5.
Margin (dB) = QP/AV Limit (dBV) - QP/AV Level (dBV)
6.
Traces shown in plot are made using a peak detector.
7.
Deviations to the Specifications: None.
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 59 of 62
V 6.3
03/24/2017
Line Conducted Measurement Data
§15.207
Plot 7-56. Line-Conducted Test Plot (L1)
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 60 of 62
V 6.3
03/24/2017
Line Conducted Measurement Data
§15.207
Plot 7-57. Line-Conducted Test Plot (N)
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 61 of 62
V 6.3
03/24/2017
8.0
CONCLUSION
The data collected relate only to the item(s) tested and show that the Samsung Portable Handset
FCC ID: A3LSMN935KOR is in compliance with Part 15 Subpart C (15.247) of the FCC Rules.
FCC ID:
A3LSMN935KOR
Test Report S/N:
1M1703230122-08.A3L
FCC Pt. 15.247 BLUETOOTH TEST REPORT
(CERTIFICATION)
Test Dates:
6/2 - 6/28/2016, 7/14/2016
© 2017 PCTEST Engineering Laboratory, Inc.
EUT Type:
Portable Handset
Reviewed by:
Quality Manager
Page 62 of 62
V 6.3
03/24/2017
Download: SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Mirror Download [FCC.gov]SMN935KOR Multi-band GSM/EDGE/UMTS/LTE Phone with Bluetooth, WLAN, RFID and ANT+ Test Report  Samsung Electronics Co Ltd
Document ID3370869
Application ID/Hs70FuUXjkw85L6lmu3NA==
Document DescriptionTest Report
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeTest Report
Display FormatAdobe Acrobat PDF - pdf
Filesize235.1kB (2938699 bits)
Date Submitted2017-04-25 00:00:00
Date Available2017-05-04 00:00:00
Creation Date2017-04-20 18:25:03
Producing SoftwareAcrobat Distiller 10.1.16 (Windows)
Document Lastmod2017-04-25 16:37:17
Document TitleTest Report
Document CreatorPScript5.dll Version 5.2.2

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : 
Create Date                     : 2017:04:20 18:25:03-04:00
Modify Date                     : 2017:04:25 16:37:17-04:00
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2017:04:25 16:37:17-04:00
Producer                        : Acrobat Distiller 10.1.16 (Windows)
Format                          : application/pdf
Creator                         : 
Title                           : 
Document ID                     : uuid:1393c075-e615-4f2d-b67b-2dc47a0e58c9
Instance ID                     : uuid:8558fbbe-2b2e-4995-ae4a-e5d3751d8054
Page Count                      : 62

Facebook Twitter Google+ RSS © FCCID.io 2017