FCC ID ACJFZA3A20A

Power out is conducted at the antenna terminal. Single Modular Approval. This device is to be used only for mobile and fixed application; and must not be co- located or operating in conjunction with any other antenna or transmitter, except in accordance with FCC multitransmitter evaluation procedures as documented in this filing. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. OEM integrators must insure that the end user has no manual instructions to remove or install this module. For mobile operating configurations the antenna gain, including cable loss, must not exceed the gains documented in this filing for, as defined in 2.1091 for satisfying RF exposure compliance. Under no conditions may an antenna gain be used that would exceed the ERP and/or EIRP power limits as specified in Part 22/24/27. The Grantee is responsible for providing the documentation required for modular use. This device has 1.4 MHz, 3 MHz, 5 MHz, 10 MHz, 15 MHz and 20 MHz bandwidth modes for LTE Bands 2/4/66; 1.4 MHz, 3 MHz, 5 MHz and 10 MHz bandwidth modes for LTE Bands 5/12; 1.4 MHz, 3 MHz, 5 MHz, 10 MHz and 15 MHz bandwidth modes for LTE Band 26; 5 MHz and 10 MHz bandwidth modes for LTE Bands 13/14/30; 5 MHz, 10 MHz, 15 MHz and 20 MHz bandwidth modes for LTE Bands 7/41. This device also supports CA UL on the LTE Bands 7/41.

Power out is conducted at the antenna terminal. Single Modular Approval. This device is to be used only for mobile and fixed application; and must not be co- located or operating in conjunction with any other antenna or transmitter, except in accordance with FCC multitransmitter evaluation procedures as documented in this filing. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. OEM integrators must insure that the end user has no manual instructions to remove or install this module. For mobile operating configurations the antenna gain, including cable loss, must not exceed the gains documented in this filing for, as defined in 2.1091 for satisfying RF exposure compliance. Under no conditions may an antenna gain be used that would exceed the ERP and/or EIRP power limits as specified in Part 22/24/27. The Grantee is responsible for providing the documentation required for modular use. This device has 1.4 MHz, 3 MHz, 5 MHz, 10 MHz, 15 MHz and 20 MHz bandwidth modes for LTE Bands 2/4/66; 1.4 MHz, 3 MHz, 5 MHz and 10 MHz bandwidth modes for LTE Bands 5/12; 1.4 MHz, 3 MHz, 5 MHz, 10 MHz and 15 MHz bandwidth modes for LTE Band 26; 5 MHz and 10 MHz bandwidth modes for LTE Bands 13/14/30; 5 MHz, 10 MHz, 15 MHz and 20 MHz bandwidth modes for LTE Bands 7/41. This device also supports CA UL on the LTE Bands 7/41.

Power out is conducted at the antenna terminal. Single Modular Approval. This device is to be used only for mobile and fixed application; and must not be co- located or operating in conjunction with any other antenna or transmitter, except in accordance with FCC multi-transmitter evaluation procedures as documented in this filing. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. OEM integrators must insure that the end user has no manual instructions to remove or install this module. For mobile operating configurations the antenna gain, including cable loss, must not exceed the gains documented in this filing for, as defined in 2.1091 for satisfying RF exposure compliance. Under no conditions may an antenna gain be used that would exceed the ERP and/or EIRP power limits as specified in Part 22/24/27. The Grantee is responsible for providing the documentation required for modular use. This device has 1.4 MHz, 3 MHz, 5 MHz, 10 MHz, 15 MHz and 20 MHz bandwidth modes for LTE Bands 2/4/66; 1.4 MHz, 3 MHz, 5 MHz and 10 MHz bandwidth modes for LTE Bands 5/12; 1.4 MHz, 3 MHz, 5 MHz, 10 MHz and 15 MHz bandwidth modes for LTE Band 26; 5 MHz and 10 MHz bandwidth modes for LTE Bands 13/14/30; 5 MHz, 10 MHz, 15 MHz and 20 MHz bandwidth modes for LTE Bands 7/41. This device also supports CA UL on the LTE Bands 7/41.

Power out is conducted at the antenna terminal. Single Modular Approval. This device is to be used only for mobile and fixed application; and must not be co- located or operating in conjunction with any other antenna or transmitter, except in accordance with FCC multi-transmitter evaluation procedures as documented in this filing. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. OEM integrators must insure that the end user has no manual instructions to remove or install this module. For mobile operating configurations the antenna gain, including cable loss, must not exceed the gains documented in this filing for, as defined in 2.1091 for satisfying RF exposure compliance. Under no conditions may an antenna gain be used that would exceed the ERP and/or EIRP power limits as specified in Part 22/24/27. The Grantee is responsible for providing the documentation required for modular use. This device has 1.4 MHz, 3 MHz, 5 MHz, 10 MHz, 15 MHz and 20 MHz bandwidth modes for LTE Bands 2/4/66; 1.4 MHz, 3 MHz, 5 MHz and 10 MHz bandwidth modes for LTE Bands 5/12; 1.4 MHz, 3 MHz, 5 MHz, 10 MHz and 15 MHz bandwidth modes for LTE Band 26; 5 MHz and 10 MHz bandwidth modes for LTE Bands 13/14/30; 5 MHz, 10 MHz, 15 MHz and 20 MHz bandwidth modes for LTE Bands 7/41. This device also supports CA UL on the LTE Bands 7/41.

Power out is conducted at the antenna terminal. Single Modular Approval. This device is to be used only for mobile and fixed application; and must not be co- located or operating in conjunction with any other antenna or transmitter, except in accordance with FCC multi-transmitter evaluation procedures as documented in this filing. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. OEM integrators must insure that the end user has no manual instructions to remove or install this module. For mobile operating configurations the antenna gain, including cable loss, must not exceed the gains documented in this filing for, as defined in 2.1091 for satisfying RF exposure compliance. Under no conditions may an antenna gain be used that would exceed the ERP and/or EIRP power limits as specified in Part 22/24/27. The Grantee is responsible for providing the documentation required for modular use. This device has 1.4 MHz, 3 MHz, 5 MHz, 10 MHz, 15 MHz and 20 MHz bandwidth modes for LTE Bands 2/4/66; 1.4 MHz, 3 MHz, 5 MHz and 10 MHz bandwidth modes for LTE Bands 5/12; 1.4 MHz, 3 MHz, 5 MHz, 10 MHz and 15 MHz bandwidth modes for LTE Band 26; 5 MHz and 10 MHz bandwidth modes for LTE Bands 13/14/30; 5 MHz, 10 MHz, 15 MHz and 20 MHz bandwidth modes for LTE Bands 7/41. This device also supports CA UL on the LTE Bands 7/41.

Power out is conducted at the antenna terminal. Single Modular Approval. This device is to be used only for mobile and fixed application; and must not be co- located or operating in conjunction with any other antenna or transmitter, except in accordance with FCC multi-transmitter evaluation procedures as documented in this filing. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. OEM integrators must insure that the end user has no manual instructions to remove or install this module. For mobile operating configurations the antenna gain, including cable loss, must not exceed the gains documented in this filing for, as defined in 2.1091 for satisfying RF exposure compliance. Under no conditions may an antenna gain be used that would exceed the ERP and/or EIRP power limits as specified in Part 22/24/27. The Grantee is responsible for providing the documentation required for modular use. This device has 1.4 MHz, 3 MHz, 5 MHz, 10 MHz, 15 MHz and 20 MHz bandwidth modes for LTE Bands 2/4/66; 1.4 MHz, 3 MHz, 5 MHz and 10 MHz bandwidth modes for LTE Bands 5/12; 1.4 MHz, 3 MHz, 5 MHz, 10 MHz and 15 MHz bandwidth modes for LTE Band 26; 5 MHz and 10 MHz bandwidth modes for LTE Bands 13/14/30; 5 MHz, 10 MHz, 15 MHz and 20 MHz bandwidth modes for LTE Bands 7/41. This device also supports CA UL on the LTE Bands 7/41.