FCC ID FKGX11BKB

This device is to be used only for mobile and fixed application; and must not be co-located or operating in conjunction with any other antenna or transmitter, except in accordance with FCC multi-transmitter evaluation procedure as documented in this filling. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. OEM integrators must insure that the end user has no manual instructions to remove or install this module. For mobile operating configurations the antenna gain, including cable loss, must not exceed the gains documented in this filling for , as defined in 2.1091 for satisfying RF exposure compliance. Under no conditions may an antenna gain be used that would exceed the ERP and/or EIRP power limits as specified in Part 22/24/27.

The Grantee is responsible for providing the documentation required for modular use.

The device has 1.4 MHz, 3 MHz, 5 MHz, 10 MHz, 15 MHz and 20 MHz bandwidth modes for LTE Bands 2/4/66; 1.4 MHz, 3 MHz, 5 MHz and 10 MHz bandwidth modes for LTE Bands 5/12; 1.4 MHz, 3 MHz, 5 MHz, 10 MHz and 15 MHz bandwidth modes for LTE Band 26; 5 MHz and 10 MHz bandwidth modes for LTE Bands 13/30; 5 MHz, 10 MHz, 15 MHz and 20 MHz bandwidth modes for LTE Bands 7/41. This device supports CA UL on the LTE Bands 7/41.

C2PC for subjected approval module is being used in a specific host (Product: Fully- Rugged Tablet PC, Brand name/ model: DURABOOK/ X11XXXXXX(X=0~9,A~Z,a~z, Blank), U11XXXXXX(X=0~9,A~Z,a~z, Blank), R11 (R5) and power reduce per tune-up procedure is applied in order to comply with exposure requirements, this grant is based on grant which issued at 04/17/2018.

This device is to be used only for mobile and fixed application; and must not be co-located or operating in conjunction with any other antenna or transmitter, except in accordance with FCC multi-transmitter evaluation procedure as documented in this filling. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. OEM integrators must insure that the end user has no manual instructions to remove or install this module. For mobile operating configurations the antenna gain, including cable loss, must not exceed the gains documented in this filling for , as defined in 2.1091 for satisfying RF exposure compliance. Under no conditions may an antenna gain be used that would exceed the ERP and/or EIRP power limits as specified in Part 22/24/27.

The Grantee is responsible for providing the documentation required for modular use.

The device has 1.4 MHz, 3 MHz, 5 MHz, 10 MHz, 15 MHz and 20 MHz bandwidth modes for LTE Bands 2/4/66; 1.4 MHz, 3 MHz, 5 MHz and 10 MHz bandwidth modes for LTE Bands 5/12; 1.4 MHz, 3 MHz, 5 MHz, 10 MHz and 15 MHz bandwidth modes for LTE Band 26; 5 MHz and 10 MHz bandwidth modes for LTE Bands 13/30; 5 MHz, 10 MHz, 15 MHz and 20 MHz bandwidth modes for LTE Bands 7/41. This device supports CA UL on the LTE Bands 7/41.

C2PC for subjected approval module is being used in a specific host (Product: Fully- Rugged Tablet PC, Brand name/ model: DURABOOK/ X11XXXXXX(X=0~9,A~Z,a~z, Blank), U11XXXXXX(X=0~9,A~Z,a~z, Blank), R11 (R5) and power reduce per tune-up procedure is applied in order to comply with exposure requirements, this grant is based on grant which issued at 04/17/2018.

This device is to be used only for mobile and fixed application; and must not be co-located or operating in conjunction with any other antenna or transmitter, except in accordance with FCC multi-transmitter evaluation procedure as documented in this filling. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. OEM integrators must insure that the end user has no manual instructions to remove or install this module. For mobile operating configurations the antenna gain, including cable loss, must not exceed the gains documented in this filling for, as defined in 2.1091 for satisfying RF exposure compliance. Under no conditions may an antenna gain be used that would exceed the ERP and/or EIRP power limits as specified in Part 22/24/27. The Grantee is responsible for providing the documentation required for modular use.

The device has 1.4 MHz, 3 MHz, 5 MHz, 10 MHz, 15 MHz and 20 MHz bandwidth modes for LTE Bands 2/4/66; 1.4 MHz, 3 MHz, 5 MHz and 10 MHz bandwidth modes for LTE Bands 5/12; 1.4 MHz, 3 MHz, 5 MHz, 10 MHz and 15 MHz bandwidth modes for LTE Band 26; 5 MHz and 10 MHz bandwidth modes for LTE Bands 13/30; 5 MHz, 10 MHz, 15 MHz and 20 MHz bandwidth modes for LTE Bands 7/41. This device supports CA UL on the LTE Bands 7/41.

This device is to be used only for mobile and fixed application; and must not be co-located or operating in conjunction with any other antenna or transmitter, except in accordance with FCC multi-transmitter evaluation procedure as documented in this filling. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. OEM integrators must insure that the end user has no manual instructions to remove or install this module. For mobile operating configurations the antenna gain, including cable loss, must not exceed the gains documented in this filling for, as defined in 2.1091 for satisfying RF exposure compliance. Under no conditions may an antenna gain be used that would exceed the ERP and/or EIRP power limits as specified in Part 22/24/27. The Grantee is responsible for providing the documentation required for modular use.

The device has 1.4 MHz, 3 MHz, 5 MHz, 10 MHz, 15 MHz and 20 MHz bandwidth modes for LTE Bands 2/4/66; 1.4 MHz, 3 MHz, 5 MHz and 10 MHz bandwidth modes for LTE Bands 5/12; 1.4 MHz, 3 MHz, 5 MHz, 10 MHz and 15 MHz bandwidth modes for LTE Band 26; 5 MHz and 10 MHz bandwidth modes for LTE Bands 13/30; 5 MHz, 10 MHz, 15 MHz and 20 MHz bandwidth modes for LTE Bands 7/41. This device supports CA UL on the LTE Bands 7/41.

Power out is conducted at the antenna terminal. Single Modular Approval. Permissive Change to cover LTE Band 48, as documented in this filing. This device is to be used only for mobile and fixed application; and must not be co- located or operating inconjunction with any other antenna or transmitter, except in accordance with FCC multi- transmitter evaluationprocedures as documented in this filing. End-users and installers must be provided with antenna installationinstructions and transmitter operating conditions for satisfying RF exposure compliance. OEM integrators mustinsure that the end user has no manual instructions to remove or install this module. For mobile operatingconfigurations the antenna gain, including cable loss, must not exceed the gains documented in this filing for, asdefined in 2.1091 for satisfying RF exposure compliance. Under no conditions may an antenna gain be used thatwould exceed the EIRP power limits as specified in Part 96. The Grantee is responsible for providing thedocumentation required for modular use. This device also supports some other bands including: LTE Bands 2/4/5/7/12/13/26/30/41/66.

Power out is conducted at the antenna terminal. Single Modular Approval. Permissive Change to cover LTE Band 48, as documented in this filing. This device is to be used only for mobile and fixed application; and must not be co- located or operating inconjunction with any other antenna or transmitter, except in accordance with FCC multi- transmitter evaluationprocedures as documented in this filing. End-users and installers must be provided with antenna installationinstructions and transmitter operating conditions for satisfying RF exposure compliance. OEM integrators mustinsure that the end user has no manual instructions to remove or install this module. For mobile operatingconfigurations the antenna gain, including cable loss, must not exceed the gains documented in this filing for, asdefined in 2.1091 for satisfying RF exposure compliance. Under no conditions may an antenna gain be used thatwould exceed the EIRP power limits as specified in Part 96. The Grantee is responsible for providing thedocumentation required for modular use. This device also supports some other bands including: LTE Bands 2/4/5/7/12/13/26/30/41/66.