EMMYW163 WLAN/Bluetooth/NFC host-based multiradio module EMMY-W1 Cover Letter Modular Approval Request (per DA 00-1407) u-blox AG

u-blox AG WLAN/Bluetooth/NFC host-based multiradio module EMMY-W1

Page 1 of EMMYW163 WLAN/Bluetooth/NFC host-based multiradio module EMMY-W1 Cover Letter Modular Approval Request (per DA 00-1407) u-blox AG
Page 2 of EMMYW163 WLAN/Bluetooth/NFC host-based multiradio module EMMY-W1 Cover Letter Modular Approval Request (per DA 00-1407) u-blox AG

RF_734_00, Issue 1
Modular Approval Request FCC (per DA 00-1407)
FCC ID: XPYEMMYW163
Items to be covered
1. The modular transmitter must have its own RF shielding.
Answer from applicant
Yes
2.
The modular transmitter must have buffered modulation/data inputs (if such inputs
are provided) to ensure that the module will comply with Part 15 requirements
under conditions of excessive data rates or over-modulation.
Yes
3.
The modular transmitter must have its own power supply regulation.
Yes
4.
The modular transmitter must comply with the antenna requirements of Section
15.203 and 15.204(c). The antenna must either be permanently attached or employ
a “unique” antenna coupler (at all connections between the module and the antenna,
including the cable)..
Yes
The modular transmitter must be tested in a stand-alone configuration, i.e., the
module must not be inside another device during testing. This is intended to
demonstrate that the module is capable of complying with Part 15 emission limits
regardless of the device into which it is eventually installed.
Yes
6.
The modular transmitter must be labeled with its own FCC ID number, and, if the
FCC ID is not visible when the module is installed inside another device, then the
outside of the device into which the module is installed must also display a label
referring to the enclosed module. This exterior label can use wording such as the
following: “Contains Transmitter Module FCC ID: XYZMODEL1” or “Contains
FCC ID: XYZMODEL1.” Any similar wording that expresses the same meaning
may be used. The Grantee may either provide such a label, an example of which
must be included in the application for equipment authorization, or, must provide
adequate instructions along with the module which explain this requirement. In the
latter case, a copy of these instructions must be included in the application for
equipment authorization.
Yes
7.
The modular transmitter must comply with any specific rule or operating
requirements applicable to the transmitter and the manufacturer must provide
adequate instructions along with the module to explain any such requirements. A
copy of these instructions must be included in the application for equipment
authorization. For example, there are very strict operational and timing
requirements that must be met before a transmitter is authorized for operation under
Section 15.231. For instance, data transmission is prohibited, except for operation
under Section 15.231(e), in which case there are separate field strength level and
timing requirements. Compliance with these requirements must be assured.
Yes
8.
The modular transmitter must comply with any applicable RF exposure
requirements. For example, FCC Rules in Sections 2.1091, 2.1093 and specific
Sections of Part 15, including 15.319(i), 15.407(f), 15.253(f) and 15.255(g),
require that Unlicensed PCS, UNII and millimeter wave devices perform routine
environmental evaluation for RF Exposure to demonstrate compliance. In
addition, spread spectrum transmitters operating under Section 15.247 are
required to address RF Exposure compliance in accordance with Section
15.247(b)(4). Modular transmitters approved under other Sections of Part 15,
when necessary, may also need to address certain RF Exposure concerns,
typically by providing specific installation and operating instructions for users,
installers and other interested parties to ensure compliance.
Yes
5.
Note: If compliance with one or more of the numbered requirements, listed above, cannot be
demonstrated, it may be possible to obtain a “Limited Modular Approval” (LMA).
Name and surname of applicant (or authorized representative):
Imad Hjije
RF_734_00, Issue 1
Date: 11/22/2016
Signature:
Download: EMMYW163 WLAN/Bluetooth/NFC host-based multiradio module EMMY-W1 Cover Letter Modular Approval Request (per DA 00-1407) u-blox AG
Mirror Download [FCC.gov]EMMYW163 WLAN/Bluetooth/NFC host-based multiradio module EMMY-W1 Cover Letter Modular Approval Request (per DA 00-1407) u-blox AG
Document ID3228825
Application IDigYAcwqWApk2iPG9ivheFw==
Document DescriptionModular Approval Cover Letter
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeCover Letter(s)
Display FormatAdobe Acrobat PDF - pdf
Filesize16.48kB (206011 bits)
Date Submitted2016-12-15 00:00:00
Date Available2017-02-16 00:00:00
Creation Date2016-11-22 16:10:10
Producing SoftwareMicrosoft® Word 2016
Document Lastmod2016-11-22 16:10:10
Document TitleModular Approval Request (per DA 00-1407)
Document CreatorMicrosoft® Word 2016
Document Author: bvos

Source Exif Data [exif.tools]:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 2
Language                        : en-US
Tagged PDF                      : Yes
XMP Toolkit                     : 3.1-701
Producer                        : Microsoft® Word 2016
Title                           : Modular Approval Request (per DA 00-1407)
Creator                         : bvos
Creator Tool                    : Microsoft® Word 2016
Create Date                     : 2016:11:22 16:10:10+01:00
Modify Date                     : 2016:11:22 16:10:10+01:00
Document ID                     : uuid:8C63DF10-8880-4C50-9A09-5B65D81D3E6C
Instance ID                     : uuid:8C63DF10-8880-4C50-9A09-5B65D81D3E6C
Author                          : bvos