PG2132 LTE Phone Test Report FCC RF Sonim Technologies, Inc.

Sonim Technologies, Inc. LTE Phone

Page 1 of PG2132 LTE Phone Test Report FCC RF Sonim Technologies, Inc.
Page 2 of PG2132 LTE Phone Test Report FCC RF Sonim Technologies, Inc.
Page 3 of PG2132 LTE Phone Test Report FCC RF Sonim Technologies, Inc.
Page 4 of PG2132 LTE Phone Test Report FCC RF Sonim Technologies, Inc.
Page 5 of PG2132 LTE Phone Test Report FCC RF Sonim Technologies, Inc.
Page 6 of PG2132 LTE Phone Test Report FCC RF Sonim Technologies, Inc.
Page 7 of PG2132 LTE Phone Test Report FCC RF Sonim Technologies, Inc.
Page 8 of PG2132 LTE Phone Test Report FCC RF Sonim Technologies, Inc.
Page 9 of PG2132 LTE Phone Test Report FCC RF Sonim Technologies, Inc.
Page 10 of PG2132 LTE Phone Test Report FCC RF Sonim Technologies, Inc.
Page 11 of PG2132 LTE Phone Test Report FCC RF Sonim Technologies, Inc.
Page 12 of PG2132 LTE Phone Test Report FCC RF Sonim Technologies, Inc.
Page 13 of PG2132 LTE Phone Test Report FCC RF Sonim Technologies, Inc.
Page 14 of PG2132 LTE Phone Test Report FCC RF Sonim Technologies, Inc.
Page 15 of PG2132 LTE Phone Test Report FCC RF Sonim Technologies, Inc.
Page 16 of PG2132 LTE Phone Test Report FCC RF Sonim Technologies, Inc.
Page 17 of PG2132 LTE Phone Test Report FCC RF Sonim Technologies, Inc.
Page 18 of PG2132 LTE Phone Test Report FCC RF Sonim Technologies, Inc.
Page 19 of PG2132 LTE Phone Test Report FCC RF Sonim Technologies, Inc.
Page 20 of PG2132 LTE Phone Test Report FCC RF Sonim Technologies, Inc.
Page 21 of PG2132 LTE Phone Test Report FCC RF Sonim Technologies, Inc.

FCC RF Test Report
Report No. : FZ792101
DYNAMIC FREQUENCY SELECTION
DFS Test Report
APPLICANT
EQUIPMENT
BRAND NAME
MODEL NAME
Sonim Technologies, Inc.
LTE Phone
Sonim
XP5800(PC2111)
FCC ID
STANDARD
CLASSIFICATION
: WYPPC2100
: FCC Part 15 Subpart E
: (NII) Unlicensed National Information Infrastructure
The product was received on Sep. 21, 2017 and completely tested on Oct. 09, 2017. We,
Sporton International (Kunshan) Inc., would like to declare that the tested sample has been
evaluated in accordance with the procedures and shown to be compliant with the applicable
technical standards.
The test results in this report apply exclusively to the tested model / sample. Without written
approval of Sporton International (Kunshan) Inc., the test report shall not be reproduced
except in full.
Approved by: James Huang / Manager
Sporton International (Kunshan) Inc.
No.3-2 Ping-Xiang Rd, Kunshan Development Zone Kunshan City Jiangsu Province 215335
China
Sporton International (Kunshan) Inc.
TEL : +86-512-57900158
FAX : +86-512-57900958
FCC ID : WYPPC2100
Page Number
: 1 of 21
Report Issued Date : Dec. 04, 2017
Report Version
: Rev. 01
FCC RF Test Report
Report No. : FZ792101
TABLE OF CONTENTS
REVISION HISTORY.......................................................................................................................................... 3
SUMMARY OF DYNAMIC FREQUENCY SELECTION TEST.......................................................................... 4
GENERAL DESCRIPTION .......................................................................................................................... 5
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
REQUIREMENTS AND PARAMETERS FOR DFS TEST .......................................................................... 9
2.1
2.2
2.3
2.4
Applicability of DFS Requirements ................................................................................................... 9
Interference Threshold values, Master or Client incorporating In-Service Monitoring ................... 11
DFS Response requirement values ................................................................................................ 11
Short Pulse Radar Test Waveforms ............................................................................................... 12
CALIBRATION SETUP AND DFS TEST RESULTS ................................................................................ 13
3.1
3.2
Applicant ........................................................................................................................................... 5
Manufacturer ..................................................................................................................................... 5
Feature of Equipment Under Test .................................................................................................... 5
Product Specification of Equipment Under Test ............................................................................... 6
Testing Site ....................................................................................................................................... 7
Applied Standards ............................................................................................................................ 7
Support Unit used in test configuration and system ......................................................................... 8
Test tool software version ................................................................................................................. 8
Calibration of Radar Waveform ...................................................................................................... 13
In-Service Monitoring: Channel Move Time, Channel Closing Transmission Time and
Non-Occupancy Period ................................................................................................................... 15
LIST OF MEASURING EQUIPMENT ........................................................................................................ 21
APPENDIX A. SETUP PHOTOGRAPHS
Sporton International (Kunshan) Inc.
TEL : +86-512-57900158
FAX : +86-512-57900958
FCC ID : WYPPC2100
Page Number
: 2 of 21
Report Issued Date : Dec. 04, 2017
Report Version
: Rev. 01
FCC RF Test Report
Report No. : FZ792101
REVISION HISTORY
REPORT NO.
VERSION
FZ792101
Rev. 01
Sporton International (Kunshan) Inc.
TEL : +86-512-57900158
FAX : +86-512-57900958
FCC ID : WYPPC2100
DESCRIPTION
Initial issue of report
ISSUED DATE
Dec. 04, 2017
Page Number
: 3 of 21
Report Issued Date : Dec. 04, 2017
Report Version
: Rev. 01
FCC RF Test Report
Report No. : FZ792101
SUMMARY OF DYNAMIC FREQUENCY SELECTION TEST
UNII
UNII Band 2-A
5250-5350MHz
UNII Band 2-C
5470-5725MHz
Bandwidth
and
Channel
40MHz
(CH102)
5510MHz
Description
Measured
Limit
Result
Channel Move Time
474.816ms
10 sec
Pass
Channel Closing
Transmission time
Non-Occupancy
Period and Client
Beacon Test
<200ms +
200 ms +
4.0 ms
aggregate of 60 ms over
(aggregate)
remaining 10 s period
No transmission
or Beacons
30 minutes
occurred
Pass
Pass
Note: Since the product is client without radar detection function, only Channel Move Time, Channel
Closing Transmission Time and Non-Occupancy Period Test are required to be performed.
Sporton International (Kunshan) Inc.
TEL : +86-512-57900158
FAX : +86-512-57900958
FCC ID : WYPPC2100
Page Number
: 4 of 21
Report Issued Date : Dec. 04, 2017
Report Version
: Rev. 01
FCC RF Test Report
Report No. : FZ792101
1 General Description
1.1 Applicant
Sonim Technologies, Inc.
1825 S. Grant St., Suite 200., San Mateo, CA, 94402
1.2 Manufacturer
Sonim Technologies (Shenzhen) Limited
2nd Floor, No. 2 Building Phase B, Daqian Industrial park, Longchang Road, 67 District, Baoan,
Shenzhen, P. R. China
1.3 Feature of Equipment Under Test
Product Feature
Equipment
Brand Name
Model Name
FCC ID
EUT supports Radios application
IMEI Code
HW Version
SW Version
EUT Stage
LTE Phone
Sonim
XP5800(PC2111)
WYPPC2100
CDMA/EV-DO/GSM/GPRS/EGPRS/WCDMA/HSPA/
DC-HSDPA/HSPA+(16QAM uplink is not supported)/LTE
WLAN 2.4GHz 802.11b/g/n HT20/HT40
WLAN 5GHz 802.11a/n HT20/HT40
Bluetooth v3.0 + EDR/ v 4.0 LE/ v 4.2 LE
Conducted: 001080001908574
Conduction: 001080001912444, 001080001912451
Radiation: 001080001912568, 001080001912576
5SA.0.0-00-7.1.2-00.25.01
Identical Prototype
Remark: The above EUT's information was declared by manufacturer. Please refer to the specifications
or user's manual for more detailed description.
Sporton International (Kunshan) Inc.
TEL : +86-512-57900158
FAX : +86-512-57900958
FCC ID : WYPPC2100
Page Number
: 5 of 21
Report Issued Date : Dec. 04, 2017
Report Version
: Rev. 01
FCC RF Test Report
1.4
Report No. : FZ792101
Product Specification of Equipment Under Test
Product Specification subjective to this standard
DFS Function
Tx/Rx Channel Frequency Range
EUT support WLAN function
Type of Modulation
Sporton International (Kunshan) Inc.
TEL : +86-512-57900158
FAX : +86-512-57900958
FCC ID : WYPPC2100
Client without radar detection function
5260 MHz ~ 5320 MHz
5500 MHz ~ 5720 MHz
<5260 MHz ~ 5320 MHz>
802.11a
802.11n HT20
802.11n HT40
<5500 MHz ~ 5720 MHz >
802.11a
802.11n HT20
802.11n HT40
802.11a/n : OFDM (BPSK / QPSK / 16QAM / 64QAM)
Page Number
: 6 of 21
Report Issued Date : Dec. 04, 2017
Report Version
: Rev. 01
FCC RF Test Report
Report No. : FZ792101
1.5 Testing Site
Sporton Lab is accredited to ISO 17025 by National Voluntary Laboratory Accreditation Program
(NVLAP code: 600155-0) and the FCC designation No is CN5013.
Test Site
Sporton International (Kunshan) Inc.
No.3-2 Ping-Xiang Rd, Kunshan Development Zone Kunshan City Jiangsu
Province 215335 China
Test Site Location
TEL : 86-512-57900158
FAX : 86-512-57900958
FCC Test Firm
Sporton Site No.
Registration No.
Test Site No.
DFS01-KS
630927
Note: The test site complies with ANSI C63.4 2014 requirement.
1.6 Applied Standards
According to the specifications of the manufacturer, the EUT must comply with the requirements of the
following standards:

FCC Part 15 Subpart E

FCC KDB 905462 D02 UNII DFS Compliance Procedures New Rules

FCC KDB 905462 D03 UNII Clients Without Radar Detection New Rules
Remark: All test items were verified and recorded according to the standards and without any deviation
during the test.
Sporton International (Kunshan) Inc.
TEL : +86-512-57900158
FAX : +86-512-57900958
FCC ID : WYPPC2100
Page Number
: 7 of 21
Report Issued Date : Dec. 04, 2017
Report Version
: Rev. 01
FCC RF Test Report
Report No. : FZ792101
1.7 Support Unit used in test configuration and system
Item Equipment Trade Name
Model Name
FCC ID
Air-AP1262N-A-K9
LDK102073
HW / FW Version
Power Cord
HW: v02
1.
WLAN AP
Cisco
Shielded, 1.8 m
FW: 12.4(25d)JA1
AC I/P:
Unshielded, 1.2 m
2.
Notebook
Lenovo
Edge E335
PPD-AR5B95
N/A
DC O/P:
Shielded, 1.8 m
1.8 Test tool software version
Item
Trade Name
Model Name
FW Version
1.
KEY-SIGHT
N7607B Signal Studio
3.0.0.0
Sporton International (Kunshan) Inc.
TEL : +86-512-57900158
FAX : +86-512-57900958
FCC ID : WYPPC2100
Page Number
: 8 of 21
Report Issued Date : Dec. 04, 2017
Report Version
: Rev. 01
FCC RF Test Report
Report No. : FZ792101
2 Requirements and Parameters for DFS Test
2.1 Applicability of DFS Requirements
EUT is client and operates as client without radar detection function.
Table 1: Applicability of DFS Requirements Prior to Use of a Channel
Operational Mode
Requirement
Master
Client
Client With
Without Radar
Radar
Detection
Detection
Non-Occupancy Period
Yes
Not required
Yes
DFS Detection Threshold
Yes
Not required
Yes
Channel Availability Check Time
Yes
Not required
Not required
U-NII Detection Bandwidth
Yes
Not required
Yes
Table 2: Applicability of DFS requirements during normal operation
Operational Mode
Requirement
Master
Client
Client
Without Radar
With Radar
Detection
Detection
DFS Detection Threshold
Yes
Not required
Yes
Channel Closing Transmission Time
Yes
Yes
Yes
Channel Move Time
Yes
Yes
Yes
U-NII Detection Bandwidth
Yes
Not required
Yes
Client Beacon Test
N/A
Yes
Yes
Sporton International (Kunshan) Inc.
TEL : +86-512-57900158
FAX : +86-512-57900958
FCC ID : WYPPC2100
Page Number
: 9 of 21
Report Issued Date : Dec. 04, 2017
Report Version
: Rev. 01
FCC RF Test Report
Report No. : FZ792101
Operational Mode
Additional requirements for devices
Master or
with multiple bandwidth modes
Client With
Client
Without Radar Detection
Radar Detection
U-NII Detection Bandwidth and
All BW modes
Statistical Performance Check
must be tested
Channel Move Time and Channel
Test using widest BW
Closing Transmission Time
mode available
All other tests
Any single BW mode
Not required
Test using the widest
BW mode available
for the link
Not required
Note
Frequencies selected for statistical performance check (Section 7.8.4) should include
several frequencies within the radar detection bandwidth and frequencies near the edge of
the radar detection bandwidth. For 802.11 devices it is suggested to select frequencies in
each of the bonded 20 MHz channels and the channel center frequency.
Sporton International (Kunshan) Inc.
TEL : +86-512-57900158
FAX : +86-512-57900958
FCC ID : WYPPC2100
Page Number
: 10 of 21
Report Issued Date : Dec. 04, 2017
Report Version
: Rev. 01
FCC RF Test Report
Report No. : FZ792101
2.2 Interference Threshold values, Master or Client incorporating
In-Service Monitoring
Maximum Transmit Power
Value (see notes 1 and 2)
≥ 200 milliwatt
-64 dBm
< 200 milliwatt
-62 dBm
Note 1: This is the level at the input of the receiver assuming a 0 dBi receive antenna.
Note 2: Throughout these test procedures an additional 1 dB has been added to the amplitude of the
test transmission waveforms to account for variations in measurement equipment. This will ensure
that the test signal is at or above the detection threshold level to trigger a DFS response.
The radar Detection Threshold, lowest antenna gain is the parameter of Interference radar DFS
detection threshold, The Interference Detection Threshold is the ( -62dBm) + (0) [dBi]+ 1 dB= -61 dBm.
2.3 DFS Response requirement values
Parameter
Value
Non-occupancy period
Minimum 30 minutes
Channel Availability Check Time
60 seconds
Channel Move Time
10 seconds See Note 1.
Channel Closing Transmission Time
200 milliseconds + an aggregate of 60 milliseconds over
remaining 10 second period. See Notes 1 and 2.
U-NII Detection Bandwidth
Minimum 100% of the 99% power bandwidth. See Note 3.
Note 1: The instant that the Channel Move Time and the Channel Closing Transmission Time begins
is as follows:
• For the Short pulse radar Test Signals this instant is the end of the Burst.
• For the Frequency Hopping radar Test Signal, this instant is the end of the last radar Burst
generated.
• For the Long Pulse radar Test Signal this instant is the end of the 12 second period defining the
radar transmission.
Note 2: The Channel Closing Transmission Time is comprised of 200 milliseconds starting at the
beginning of the Channel Move Time plus any additional intermittent control signals required to
facilitate Channel changes (an aggregate of 60 milliseconds) during the remainder of the 10 second
period. The aggregate duration of control signals will not count quiet periods in between
transmissions.
Note 3: During the U-NII Detection Bandwidth detection test, radar type 0 is used and for each
frequency step the minimum percentage of detection is 90%. Measurements are performed with no
data traffic.
Sporton International (Kunshan) Inc.
TEL : +86-512-57900158
FAX : +86-512-57900958
FCC ID : WYPPC2100
Page Number
: 11 of 21
Report Issued Date : Dec. 04, 2017
Report Version
: Rev. 01
FCC RF Test Report
Report No. : FZ792101
2.4 Short Pulse Radar Test Waveforms
As the EUT is a Client Device with no Radar Detection, only one type radar pulse is required for the
testing. Radar Pulse type 0 was used in the evaluation of the Client device for the purpose of
measuring the Channel Move Time and the Channel Closing Transmission Time.
Radar
Type
Minimum
Pulse
Width
PRI (µsec)
Number of Pulses
(µsec)
Percentage of
Minimum
Successful
Trials
Detection
1428
1-5
150-230
6-10
11-20
18
60%
30
60%
30
23-29
60%
30
200-500
16-18
60%
30
200-500
12-16
60%
30
80%
120
Test A
Test B
Aggregate (Radar Types 1-4)
Test A: 15 unique PRI values randomly selected from the list of 23 PRI values in Table 5a
Test B: 15 unique PRI values randomly selected within the range of 518-3066 μsec, with a minimum
increment of 1 μsec, excluding PRI values selected in Test A
A minimum of 30 unique waveforms are required for each of the short pulse radar types 2 through 4.
For short pulse radar type 1, the same waveform is used a minimum of 30 times. If more than 30
waveforms are used for short pulse radar types 2 through 4, then each additional waveform must also
be unique and not repeated from the previous waveforms.
If more than 30 waveforms are used for Short Pulse Radar Type 1, then each additional waveform is
generated with Test B and must also be unique and not repeated from the previous waveforms in Tests
A or B.
The aggregate is the average of the percentage of successful detections of short pulse radar types 1-4.
Sporton International (Kunshan) Inc.
TEL : +86-512-57900158
FAX : +86-512-57900958
FCC ID : WYPPC2100
Page Number
: 12 of 21
Report Issued Date : Dec. 04, 2017
Report Version
: Rev. 01
FCC RF Test Report
Report No. : FZ792101
3 Calibration Setup and DFS Test Results
3.1 Calibration of Radar Waveform
3.1.1 Radar Waveform Calibration Procedure
The Interference Radar Detection Threshold Level is (-62dBm) + (0) [dBi]+ 1 dB= -61dBm that had
been taken into account the output power range and antenna gain. The following equipment setup was
used to calibrate the radiated Radar Waveform. A vector signal generator was utilized to establish the
test signal level for radar type 0. During this process there were no transmissions by either the Master
or Client Device. The spectrum analyzer was switched to the zero span (Time Domain) at the frequency
of the Radar Waveform generator. Peak detection was used. The spectrum analyzer resolution
bandwidth (RBW) and video bandwidth (VBW) were set to 3 MHz to measure the type 0 radar
waveform. The spectrum analyzer had offset -5.82dB to compensate receiving horn antenna gain
10.32dBi and RF cable loss 4.5dB. The vector signal generator amplitude was set so that the power
level measured at the spectrum analyzer was (-62dBm) + (0) [dBi]+ 1 dB= -61 dBm. Capture the
spectrum analyzer plots on short pulse radar waveform.
3.1.2 Radiated Calibration Setup
3.1.3 Calibration Deviation
There is no deviation with the original standard.
Sporton International (Kunshan) Inc.
TEL : +86-512-57900158
FAX : +86-512-57900958
FCC ID : WYPPC2100
Page Number
: 13 of 21
Report Issued Date : Dec. 04, 2017
Report Version
: Rev. 01
FCC RF Test Report
Report No. : FZ792101
3.1.4 Radar Waveform Calibration Result
<40MHz / 5510 MHz> Radar Type 0
Radar / DFS detection threshold level and the burst of pulses on the Channel frequency
Sporton International (Kunshan) Inc.
TEL : +86-512-57900158
FAX : +86-512-57900958
FCC ID : WYPPC2100
Page Number
: 14 of 21
Report Issued Date : Dec. 04, 2017
Report Version
: Rev. 01
FCC RF Test Report
Report No. : FZ792101
3.2 In-Service Monitoring: Channel Move Time, Channel Closing
Transmission Time and Non-Occupancy Period
3.2.1 Limit of In-Service Monitoring
The EUT has In-Service Monitoring function to continuously monitor the radar signals, If radar is
detected, it must leave the channel (Shutdown). The Channel Move Time to cease all transmissions on the
current Channel upon detection of a Radar Waveform above the DFS Detection Threshold within 10 sec. The
total duration of Channel Closing Transmission Time is comprised of 200 milliseconds starting at the
beginning of the Channel Move Time plus any additional intermittent control signals required to facilitate
Channel changes (an aggregate of 60 milliseconds) during the remainder of the 10 second period. The
aggregate duration of control signals will not count quiet periods in between transmissions.
Non-Occupancy Period time is 30 minute during which a Channel will not be utilized after a Radar
Waveform is detected on that Channel. The non-associated Client Beacon Test is during the 30 minutes
observation time. The EUT should not make any transmissions in the DFS band after EUT power up.
Sporton International (Kunshan) Inc.
TEL : +86-512-57900158
FAX : +86-512-57900958
FCC ID : WYPPC2100
Page Number
: 15 of 21
Report Issued Date : Dec. 04, 2017
Report Version
: Rev. 01
FCC RF Test Report
Report No. : FZ792101
3.2.2 Test Procedures
1.
The radar pulse generator is setup to provide a pulse at frequency that the Master and Client are
operating. A type 0 radar pulse with a 1us pulse width and a 1428 us PRI is used for the testing.
2.
The vector signal generator is adjusted to provide the radar burst (18 pulses) at a level of
approximately -62dBm at the antenna of the Master device.
3.
A trigger is provided from the pulse generator to the DFS monitoring system in order to capture
the traffic and the occurrence of the radar pulse.
4.
A U-NII device operating as a Client Device will associate with the Master at Channel. The
MPEG file “TestFile.mpg” specified by the FCC is streamed from the “file computer” through the
Master to the Client Device and played in full motion video using Media Player Classic Ver.
6.4.8.6 in order to properly load the network for the entire period of the test.
5.
When a radar Burst with a level equal to the DFS Detection Threshold + 1dB is generated on the
Operating Channel of the U-NII device. At time T0 the Radar Waveform generator sends a Burst
of pulse of the radar waveform at Detection Threshold + 1dB.
6.
Observe the transmissions of the EUT at the end of the radar Burst on the Operating Channel.
Measure and record the transmissions from the EUT during the observation time (Channel Move
Time). One 12 seconds plot is reported for the Short Pulse Radar Types 1. The plot for the Short
Pulse Radar Types start at the end of the radar burst. The Channel Move Time will be calculated
based on the zoom in 600ms plot of the Short Pulse Radar Type.
7.
Measurement of the aggregate duration of the Channel Closing Transmission Time method.
With the spectrum analyzer set to zero span tuned to the center frequency of the EUT operating
channel at the radar simulated frequency, peak detection, and max hold, the dwell time per bin is
given by: Dwell (0.4ms)= S (12000ms) / B (30000); where Dwell is the dwell time per spectrum
analyzer sampling bin, S is the sweep time and B is the number of spectrum analyzer sampling
bins. An upper bound of the aggregate duration of the intermittent control signals of Channel
Closing Transmission Time is calculated by: C (ms)= N X Dwell (0.4 ms); where C is the Closing
Time, N is the number of spectrum analyzer sampling bins (intermittent control signals) showing
a U-NII transmission and Dwell is the dwell time per bin.
8.
Measure the EUT for more than 30 minutes following the channel move time to verify that no
transmissions or beacons occur on this Channel.
Sporton International (Kunshan) Inc.
TEL : +86-512-57900158
FAX : +86-512-57900958
FCC ID : WYPPC2100
Page Number
: 16 of 21
Report Issued Date : Dec. 04, 2017
Report Version
: Rev. 01
FCC RF Test Report
Report No. : FZ792101
3.2.3 Test Setup
Radiated Test Setup Photo
3.2.4 Test Deviation
There is no deviation with the original standard.
Sporton International (Kunshan) Inc.
TEL : +86-512-57900158
FAX : +86-512-57900958
FCC ID : WYPPC2100
Page Number
: 17 of 21
Report Issued Date : Dec. 04, 2017
Report Version
: Rev. 01
FCC RF Test Report
Report No. : FZ792101
3.2.5 Result of Channel Move Time, Channel Closing Transmission Time and
Non-Occupancy Period for Client Beacon Test
Test Mode :
Client without radar detection
Test Engineer : George Peng
BW / Channel
40MHz / 5510MHz
Temperature :
25.2℃
Relative Humidity : 43%
Test Item
Test Result
Limit
Pass/Fail
Channel Move Time
474.816 ms
< 10s
Pass
< 260ms
Pass
≥ 30 min
Pass
Channel Closing Transmission Time
200ms +
4.0 ms
Non-Occupancy Period
≥ 30
Note: The Channel Closing Transmission Time is comprised of 200 milliseconds starting at the beginning of
the Channel Move Time plus any additional intermittent control signals required to facilitate a Channel move
(an aggregate of 60 milliseconds) during the remainder of the 10 seconds period. The aggregate duration of
control signals will not count quiet periods in between transmissions.
Sporton International (Kunshan) Inc.
TEL : +86-512-57900158
FAX : +86-512-57900958
FCC ID : WYPPC2100
Page Number
: 18 of 21
Report Issued Date : Dec. 04, 2017
Report Version
: Rev. 01
FCC RF Test Report
Report No. : FZ792101
3.2.6 Channel Move Time, Channel Closing Transmission Time and Non-Occupancy
Period for Client Beacon Test Plots
<40MHz / 5510> In-Service Monitoring
Channel Move Time &
Channel Closing Transmission Time
Non-Occupancy Period
Non-associated test
Master was off. (beacon test)
Note:
Dwell (0.4 ms)= Sweep Time (12000 ms) / Sweep Point Bins (30000)
Channel Closing Transmission Time (200 +4.0 ms) = 200 + Number (10 X Dwell (0.4 ms) < 260ms
Sporton International (Kunshan) Inc.
TEL : +86-512-57900158
FAX : +86-512-57900958
FCC ID : WYPPC2100
Page Number
: 19 of 21
Report Issued Date : Dec. 04, 2017
Report Version
: Rev. 01
FCC RF Test Report
Report No. : FZ792101
3.2.7 Data Traffic and Noise Floor Plots
EUT data traffic (Client)
Access Point data traffic (Master)
Noise Floor (No transmission)
Sporton International (Kunshan) Inc.
TEL : +86-512-57900158
FAX : +86-512-57900958
FCC ID : WYPPC2100
Page Number
: 20 of 21
Report Issued Date : Dec. 04, 2017
Report Version
: Rev. 01
FCC RF Test Report
Report No. : FZ792101
4 List of Measuring Equipment
Instrument
Manufacturer
Model No.
Serial No.
Characteristics
Spectrum
Analyzer
R&S
FSV7
101472
10Hz~7GHz
Signal
Generator
Key-Sight
N5182B
Signal
Generator
R&S
Horn Antenna
Calibration
Date
Due Date
Remark
Jan. 19, 2017 Oct. 09, 2017
Jan. 18, 2018
DFS
(DFS01-KS)
MY56200417
100KHz ~ 6GHz Mar. 16, 2017 Oct. 09, 2017
Mar. 15, 2018
DFS
(DFS01-KS)
SMJ100A
101908
100KHz ~ 6GHz Jan. 19, 2017 Oct. 09, 2017
Jan. 18, 2018
DFS
(DFS01-KS)
BEIJING
XIBAO
XB-WDB-A18
040505
1GHz ~ 18GHz Jan. 22, 2017 Oct. 09, 2017
Jan. 21, 2018
DFS
(DFS01-KS)
Horn Antenna
Com-Power
AHA-118
701030
1GHz ~ 18GHz Oct. 24, 2016 Oct. 09, 2017
Oct. 23, 2017
DFS
(DFS01-KS)
RF cable
SUCOFLEX
104;106
52119/6
MY9623/4
1GHz ~ 18GHz Oct. 08, 2017 Oct. 09, 2017
Oct. 07, 2018
DFS
(DFS01-KS)
Sporton International (Kunshan) Inc.
TEL : +86-512-57900158
FAX : +86-512-57900958
FCC ID : WYPPC2100
Test Date
Page Number
: 21 of 21
Report Issued Date : Dec. 04, 2017
Report Version
: Rev. 01
Download: PG2132 LTE Phone Test Report FCC RF Sonim Technologies, Inc.
Mirror Download [FCC.gov]PG2132 LTE Phone Test Report FCC RF Sonim Technologies, Inc.
Document ID3671041
Application IDfVl0VQ2MlqcD42xE+TbzGQ==
Document DescriptionTest Report Reference XP5800 NII DFS
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeTest Report
Display FormatAdobe Acrobat PDF - pdf
Filesize64.27kB (803433 bits)
Date Submitted2017-12-11 00:00:00
Date Available2017-12-13 00:00:00
Creation Date2017-12-04 18:18:19
Producing SoftwareMicrosoft® Word 2010
Document Lastmod2017-12-04 19:05:57
Document TitleFCC RF Test Report
Document CreatorMicrosoft® Word 2010
Document Author: WBU Documentation Depr.

Source Exif Data [exif.tools]:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Author                          : WBU Documentation Depr.
Create Date                     : 2017:12:04 18:18:19+08:00
Creator                         : Microsoft® Word 2010
Modify Date                     : 2017:12:04 19:05:57+08:00
Producer                        : Microsoft® Word 2010
Title                           : FCC RF Test Report
Has XFA                         : No
Language                        : zh-CN
Tagged PDF                      : Yes
Page Count                      : 21